Advertisement
I\)
I\.)
Using the
SYSTEM
CONTROL connectors
The SYSTEM CONTROL oonnectors can be used to connect a AG-VC205 video/computer interface so that the
mon~or can be controlled using a personal computer.
Rear of mon ilor
~fil~~
Example of SYSTEM CONTROL signal connections
Perao nal computer
CJ
Monitor
AG-VC205
video/computer
interface
SYSTEM CONTIIOL connectors
©@
IN
OUT
SYSTEM
CONTROL
Monitor
©
OUT
:~
NOTE:
•
Special software d8Signed for use with this monitor is required in order to use the SYSTEM CONTROL
connectors to control \he monitor using a personal computer. Please oontact the place of purchase for
further details.
•
Read the instruction manuals for the AG-VC205 video/oompu\er interface and the computer being
connected in addition to this instruction manual.
•
In \his system. the monitor is controlled by uni-directional communication.
Using
the MULTI
IN
connector
The
MULTI
IN oonnector on this mon~or incorporates a stereo mini pin jack for audio signals and a high-density D-
sub 15-pin connec·:or. The high-density D-sub 15-pin connector can be connected to a RGB signaVYP,P, signal
source
or
a video
Signal
source, and allows the input selection lo be swttched exlerna0y.
Rear
of
monitor
tiigh-density D·SU b 15-
pi n connector {female) •
MULTI
IN connector
stereo
mini
pin
jacl<
SeeJI from the outside
S~nal
specificati'ons
!or h Ign-<1ensity
D-sub
15-pin
connector
-
-
...
- -
..
Pin
No.
Signal
Name
Pin
No.
SlgnalName
Pin No.
Signal Name
Q)
R/Pn
®
GND (ground)
®
Video
®
G/Y
(Z)
G
ND
(g rouncf)
@
R1
@
B/Pa
®
G
ND
(ground)
@
HD/SYNC
@)
R2
®
NC
(not connected)
®
VD
@
GND
(ground)
@l
GND
(ground)
@
NC
(not connected)
•·Signa
I
connections
Example
of
video
signal equipm6f11:
;-~
~_-_-_-_-_-_-._-~---_-_-_-_-_-_-_-_-_-~--·:
• I
l
•• :
ll;(]1:
Pe1$onal computer
E-~~1
Multi
J.-ser
disc
player
__
~
11 :,
t~
_3l
Video
VTR
NOTE:
•
If the
synchronizing
signal used for RGB signal orYPoP, signal input is a compostte sync signal,
connect pin 'lo. 13;
if
it is a separate sync signal, oonnect the horizontal sync signal to pin No. 13 and
connect the vertical sync signal to pin No. 14.
•
Read
the
instruction manuals tor the AG.VC205 video/computer interface and the computer being
connected in addttion to this instruction manual.
•
Swttciiing between the video signal source and RGB/YP,P, signal source connected to the high-
density D-sub 15-pin connector can be controlled externally via pin No. 4 (R2) and pin No. 12 (R1).
Refer
to
the following page for detailS.
•
Only
a
single audio signal system can be input via the stereo mini pin jack to the right of the high-
density D-sub 15-pin connector.
•
If
a RGB
signal or YPsP, signal source is connected, you will need to set the RGB/YP,P, button
underneath
the
remote control unit cowr in accordance with which type of signal is being input.
•
If
or
MULTI
has been selected using the input selection buttons on the remote control untt of the
monitor control panel on the front of the monitor, the RGB signals or YPoP, signals from the signal
source connected to the high-density D-sub 15-pin MULTI IN connector will be received and displayed.
C
-;-I
s::
w
~
0
:e
Advertisement
