Advertisement
~
0
Using the
operation
buttons under the remote control unit cover
The
buttons which
are
visible after
the
remote
control urilt coYer
has
been
removed
Include
some buttons
which
do
not
operate
at £111,
or only
operate
when
certain
types
of
signals
are
being
input, when the ON
SCREEN
button
is
set
to OFF.
Refer
to the
table shown
below for details
or,
when the various buttons
can
be operated.
-~•o--o.
Cover
.::::::.M
Input
aignal
ON SCREEN
button
aetting
VIDEOIS-VIDEO bUtton
RGB/YPaP,
button
BLUE
button
MONO
button
SYNC button
APT
FREQ
button
CLAMP
button
COLOR
TEMP
button
GAIN/BIAS/RGB oottons
PIN
button
CENT
button
SIZE
button
0 ISP
STD
button
DEGAUSS
button
LANDING
button
STORE
button
ID SET button/Numeric buttons
0--can
be
operated
x·••caMot
be
operated
B\Jttona undemealll
cover
0G{t)
0•0
CD
CD
CD
CO
CD
CD
(D
CD
<D
CD
>P\'t)<
Video
signal
$-VIDEO
algnal
AGBslgnal
ON
OFF
ON
OFF
ON
OFF
0
0
0
0
X
X
X
X
X
X
0
X
0
X
0
X
X
X
0
X
0
X
X
X
X
X
X
X
0
)(
X
X
X
X
X
X
X
X
X
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
0
0
0
0
0
0
X
0
X
0
X
0
)(
0
X
0
X
0
X
0
X
0
X
YP,P, aignal
ON
OFF'
X
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
X
0
0
0
)(
0
X
0
X
Monitor
ID function
When using
muttiple
mon~ors
togelher, indMdual
monitors can
be
operated separately using
the
acceesory
remote
control
untt
by
assigning
an
ID numberto
each
monitor.
Monitors
are
assigned
an
IO
number, and then
th is number
is
specified when you
wish to
operate
the
monitor.
Setting
ID
numbers
• Setting of
ID
numbers i;
carried
out using the accessory remote
conlrol
unit.
• 10
numbers
can
be
set from 100
to 1099.
•
II the
10
number is
set
to
"O",
the
monitor can
be
operated regardless of the ID number
specif,ed.
• The
10
number
is
set
to -0- at the lime
of shipment
from
the factory.
Setting procedure (Ex*mpl9:
To set
the
ID number
to "'
8")
~~
Lru
~
D
[]J
I
I
~g
, ..
,I
I
[fil
D
~
~
D
I
'8
8
l
l
1
~
69
r.~
I
©Press
the
ON
SCREEN
button
to
set
the
on-screen
display to
ON.
®
Press ltle ID SET
button
continuously for approximately
3
seconds
or
more to
switoh to
10
number
setting
mode.
NOTE:
•
When
ID
number
setting
mode is active.
the
on-screen_ displays
appear in
pale blue
color.
•
When IO number
setting
mode
Is aclive,
nooe
of the
buttons
wor1< excepl the POWER
button,
10
SET button
and
the
num&ric
buttons.
@Use
the
numeric
buttons
to
set
the
10
number.
(1)
Press
the
"1" button.
(2) Press
the
·~
button.
NOTE:
•
If
you
would like
to canoe!
the
se1ting
before
tt
is
c001pklte,
press the POWER button
to
tum off the power.
The ID number setting value will
then
return
to
its original
value.
©Once the
ID number has been
set
to
"19', press
the ID
SET
button.
The
ID number
will then
be
stored in
memory
and the on-
screen display
wiM
appear in green.
NOTE:
•
After
an ID number has been
set,
the ID number
specified
will
be automatically switch
ed to
"O'.
Refer
to
the
following
page
for
details on hOw
to
specify
an
10
number.
~
•
a:
c.)
5l
~
Advertisement
