Advertisement
MSPECIFICATIONS
Output Impedance
1kQ
Recommended Load Impedance... 10 kQ or greater
* OdBu = 0.775 Vrms
* In the itterest of product unprovement, the specifications and/or appearance of this unit
are subject to
change without prior notice.
Copyright © BOSS CORPORATION
MIPANEL DESCRIPTION
240 :option) to this jack.
battery.
BM BYPASS ¢ -B™..
'
a.
tt»
+448
\
) {
) Cayeasse ® (
)
a
ei
ArB MIE
%
NM _
Coveassd?
SS
o 920
OUTPUT SELECT
adaptor may damage the unit.
@AC Adaptor Out Jack
Connect an AC adaptor
( BOSS PSA-120,
220 or
* Use of an AC adaptor
eliminates the need
for
*Be
sure
to use
the
specified
AC
adaptor
(PSA-120,
220 or 240).
Using
any
other
Instructions
Thank
you
for
purchasing
the
BOSS
LS-2 Line
Selector.
To make the best use of the unit, please
read the instructions caretully.
@The
LS-2
provides
two
separate
line-loop
oul-
puts.
@The
LS-2 features
6 different
modes
(including
effect
loop
selector
and
line
selector)
that
enhance its versatility.
@£Each line has an indicator, allowing you to easily
determine the current state of the unit.
* These indicators also serve as a battery check.
When they become dim (or do not light at all),
replace the battery immediately.
@Level Contro! Knobs A/B
Each knob controls the output level of the corre-
sponding line ( A/B ). The output level is variable
from —co( muted ) to +20qB.
%* When
a knob
is set to the center
position, the
input and output levels are equal.
When an AC adaptor is being used to power the
LS-2,
power
can
also
be
supplied
to
another
compact effect unit by connecting a paralleled DC
cord ( PCS-20A : option ) to this jack.
*When
you
are
using
battery
power,
the
AC
Adaptor Out Jack does not function.
* When
using the PSA-120,
220 or 240,
be sure
that the total current draw of the LS-2 and any
external effect unit does not exceed 200mA.
© output
Line Selector
@Line Indicators A/B
The appropriate indicator lights when
the corre-
8
sponding line ( A/B ) is selected.
@Send Jacks ( A/B )
These jacks send the signals received by the Input
Jack when the corresponding
line ( A/B ) is in
use.
@oOutput Jack
Connect
an amplifier or other effect unit to this
jack.
@Pedal Switch
This switch selects the line to be used.
LS-2
ane
Amurbassg
©
7
"oN
kee
OE
Pine
®
Bet
cae soordrecie
© SEND — E)- RETURNE-
~ B- RETURNG
|F
€ output
INPUT €
Line Selector
LS-2
nc 8 barren wd
POWERED
@Thumb Screw
Loosen
this screw
to open
the pedal for battery
replacement.
For a
detailed
explanation,
see
"Battery Replacement".
@Mode Selector Switch
This switch
selects
the operating
mode.
For a
detailed explanation, see "MODE DESCRIPTION',
@Return Jacks A/B
These jacks feed the signal from the correspond-
ing line ( A/B ) into the unit.
@input Jack
Connect an electric/electronic musical instrument
(such as an electric guitar) to this jack.
* Connecting
a plug to the input Jack
automati-
cally turns the unit on. Disconnect the plug from
the Input Jack when the unit is not in use.
Line Selector
Advertisement
