Related Manuals for SolarEast PowerCool-LFP-HV Series
Summary of Contents for SolarEast PowerCool-LFP-HV Series
- Page 1 PowerCool-LFP-HV series Operation Manual Version: 1.0 版本：1.0 Jiangsu SolarEast Energy Storage Technology Co., Ltd...
- Page 2 All brands and product names are trademarks or registered trademarks of their respective holders. This Manual introduces PowerCool-LFP-HV manufactured by SolarEast. Please read this manual before you install the product and follow the instructions carefully during the installation process. Should you have any confusion, please contact SolarEast for advice and clarification.
-
Page 3: Table Of Contents
CONTENTS 1 . Introduction 1.1Content and Structure of this Document This document is valid for PowerCool-LFP-HV battery system. 1. Introduction …………………………………………………………………………………… 1 This document describes the product information, and guidance for installation, as well as APP 1.1 Content and Structure of this Document ……………………………………………… 1 configuration and commissioning. -
Page 4: Definition Of Abbreviations And Nouns
・If the battery is stored for long time, it is required to charge it every six months, and the recom- NOTICE mended SOC should be 50%~55%. The battery shall not be stored for more than 12 months if the NOTICE indicates a situation which, if not avoided, can result in property damage. storage temperature is -10 ~ 25℃, not more than 6 months if the storage temperature is 25 ~ 35 Warning electric shock. -
Page 5: System Introduction
The final right of interpretation is reserved by If the battery is wet or submerged in water, do not try to access it. Contact customer service for Jiangsu SolarEast Energy Storage Technology Co., Ltd. technical assistance. -
Page 6: Application Scenario
1) Battery Control Box Display Panel 3.2 Application scenario If WiFi is to be reconnected, press the button and hold for 5s till the WIFI icon on the screen flashes, and then proceed with WiFi connection on App by following the procedures set out in Section 5.17 and 5.21 below. -
Page 7: Package Items
4.3 Installation location Make sure that the installation location meets the following conditions: ・The floor is flat and level; ・There are no flammable or explosive materials nearby; ・The ambient temperature is within the range from 0°C to 50°C; ・The temperature and humidity (<60%RH) are maintained at a constant level; ・There is minimal dust and dirt in the area.;... -
Page 8: Cables Connection
4) Tighten M6*12 screws into the threaded holes on both sides of Battery Control Box and each 2) Place battery pack in the right place of the pedestal. CAUTION: align the battery pack and pack. pedestal before putting it on, make sure the couplings are on the same line to avoid any structur- al damage. -
Page 9: Power On
5.1 Download our APP： BAT- BAT+ APP for iOS: Open up the APP Store, type in 'SolarEast PowerCool' in the Search tab to search and download. APP for Android: Open up the Google Play, type in 'SolarEast PowerCool' in the Search tab to search and download. - Page 10 5.5 Click ‘get a verification code’ and retrieve it from the mailbox. Insert the verification code 5.3 Click ‘Register’ and go to this page to select identity received on this page, set the password, check ‘I agree’ and click ‘Enter’. 5.4 Go to this page after selecting identity, insert the email address to be signed in and click 5.6 Click ‘Service Agreement’...
- Page 11 5.9 On this page, you can reset password by inserting the new password twice, and then click 5.7 Click to switch language and go to the front page. 5.10 The picture demonstrates a distributor’s account. 5.8 Click ‘Retrieve the password’ and go to this page, you may insert the account number, obtain It shows such figures as the number of devices installed, total installed capacity, newly increased a verification code via email, input the verification code and click ‘Next step’.
- Page 12 5.11 Click ‘System installed’ on the front page, you can view the systems you created. You may 5.13 Click any item on the system list, you will go to the ‘System information’ page, where you search by system name, email or address. may view and edit system information.
- Page 13 5.15 Click ‘+’ on the ‘Battery list’ page and then you may add a new device by scanning its tag 5.17 Scan tag code and go to ‘Add device’ page, and then click ‘Wireless connection’ for WIFI code. configuration. 5.18 Click on "How to Add a Device" to view the step-by-step instructions for adding a device. 5.16 Find our label code on the side of the device and scan it.
- Page 14 On this page, click on "Wireless LAN" to access the Wi-Fi configuration page and connect to 5.19 On the system WIFI page, you can find the device WIFI name based on its SN code. Device WIFI name: SOLAREAST-(device SN code) the device's Wi-Fi.
- Page 15 5.21 When the network is successfully configured, a prompt will pop out. 5.23 You may check the operating information of the device and view the upgrade protocol. Click ‘Bind device information’ button, and return to device list page when the binding is done. 5.22 Click any item on the battery list you will go to the device details page, where you can view such data as battery SOC, battery temperature, voltage, power, current, operating information, 5.24 View alarm data...
- Page 16 5.25 View cell running data 5.27 You are allowed to change avatar, name and contact on ‘Account settings’ page. 5.28 On ‘Installer management’ page, you may view installers under your name. Click each 5.26 [Distributor account] ‘My’ page features the following functions: checking personal information, viewing messages, installer to view the details.
- Page 17 5.29 You may view client details by clicking ‘Client management’. By clicking the system list, you 5.31 On this page you may report problems encountered and view historical feedback. may view the system information. 5.30 Language and temperature unit switching 5.32 On ‘FAQ’...
- Page 18 5.33 View APP version details. 5.35 On this page, you may change password or email address. You may also view list of shared information, log off, view service agreement and privacy agreement, clear cache and cookies, and log out. 5.34 ‘About us’ pages shows company profile and contact information of the supplier. 5.36 On ‘Account and security’...
-
Page 19: Maintenance
5.37 On account cancellation page, you are allowed to cancel your account. 6.Maintenance 6.1 Capacity calibration It is better to fully charge-discharge the battery for the capacity calibration at least once every six months (if available). Please conduct the calibration maintenance according to the following steps: 1)Make sure there is a relatively stable power supply source to charge the battery at a maximum charge current of 50A, e.g.
Need help?
Do you have a question about the PowerCool-LFP-HV Series and is the answer not in the manual?
Questions and answers