Related Manuals for Jetson Safara Max JSAFX-NAV
Summary of Contents for Jetson Safara Max JSAFX-NAV
- Page 1 Safara Max Kids' 24V Ride-On A guide for your ride. IMPORTANT: READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE. MODELS: JSAFX-NAV | JSAFX-PUR...
- Page 3 Jetson's top two riding rules: Be safe. Have fun!
-
Page 4: Table Of Contents
Contents Safety Warnings ......................4 Warranty Coverage . - Page 5 Attaching the Steering Wheel ..................4 8 Inserting the Seat Base ....................5 1 Attaching the Seats .....................5 2 Attaching the Side Mirrors ........
-
Page 6: Safety Warnings
Safety Warnings • Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use. • Failure to use correct charger can result in fire and explosion. •... - Page 7 • Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death. • If the brake loosens, please adjust with a hexagon wrench, or please contact the Jetson Care Team. • Replace worn or broken parts immediately.
- Page 8 For all maintenance repairs and needs beyond the capability of the consumer, which may include but not be limited to: such as proper maintenance of brakes, control cables, bearing adjustments, wheel adjustments, lubrication, reflectors, tires and handlebar and seat adjustments, please contact the Jetson Care Team for assistance at: ridejetson.com/chat ridejetson.com/support...
-
Page 9: Warranty Coverage
Your new Jetson product is warranted against defects in materials and workmanship as indicated on ridejetson.com/warranty for a period of time from the date of original retail purchase when used in accordance with Jetson's user manuals (refer to ridejetson.com/support). Under this warranty, you will be able to direct your claims to Jetson even in situations where you purchased the Jetson Product from one of our authorized retailers. -
Page 11: About Your Safara Max
1. About your Safara Max Identifying Your Safara Max Model & Using This Manual OUR PRODUCTION PROCESSES HAVE CHANGED THROUGHOUT THE LIFE OF THE SAFARA MAX, AFFECTING THE ASSEMBLY STEPS THAT THE CUSTOMER NEEDS TO TAKE IN ORDER TO GET THE PRODUCT READY FOR USE. TO DETERMINE WHICH STEPS IN THIS MANUAL ARE APPLICABLE TO YOU, YOU’LL FIRST NEED TO IDENTIFY WHICH MODEL OF THE SAFARA MAX YOU HAVE. -
Page 12: What's In The Box
What's in the Box BODY FRONT AXLE WITH STEP REAR TAILSTOCK—SIDE SEAT WITH SEATBELT (X2) STEERING BRACKET FRAME (X2; LEFT & RIGHT) (X2; LEFT & RIGHT) DASHBOARD REAR AXLE GEAR BOX & ROD STEERING WHEEL STEERING ROD REMOTE CONTROL (X2; LEFT & RIGHT) SIDE MIRROR FRONT FENDER FRONT WHEEL (X2) - Page 13 LOOSE IN THE BOX FOR MODELS ONLY; PRE-ATTACHED ON THE BODY FOR MODELS NOTE: IMAGES MAY NOT REFLECT EXACT APPEARANCE OF ACTUAL PRODUCT.
- Page 14 HARDWARE: NOTE: SOME HARDWARE USED FOR ASSEMBLY IS PRE-ATTACHED ON PARTS OF THE SAFARA MAX. LOCATIONS AND INSTRUCTIONS FOR USE OF PRE-ASSEMBLED HARDWARE ARE NOTED IN THE ASSEMBLY DIRECTIONS. LARGE NUT SMALL NUT WASHER SCREW CURVED PIN STRAIGHT PIN (INCLUDING (INCLUDING (INCLUDING (INCLUDING...
-
Page 15: Specs & Features
Specs & Features • MAX SPEED IN FAST MODE: 5 MPH • MAX SPEED IN LOW MODE: 1.9 MPH • RUN TIME: 1 - 2 HOURS • BATTERY: RECHARGEABLE 24V, 7AH • REMOTE CONTROL BATTERIES: 2 AAA BATTERIES (NOT INCLUDED) •... -
Page 16: Online Resources
Online Resources Scan for our most updated Safara Max onboarding materials and support resources. -
Page 17: Getting Started Starting Notes
2. Getting Started Starting Notes · REMOVE ALL PACKAGING BEFORE BEGINNING ASSEMBLY. · THE DIRECTIONS GIVEN IN THIS MANUAL—RIGHT, LEFT, FRONT/FORWARD, AND REAR/BACK—ARE ORIENTED AS THE RIDER WOULD SEE THEM WHEN SEATED IN THE SAFARA MAX. THE "RIGHT SIDE," FOR EXAMPLE, IS THE SIDE WHERE THE RIDER’S RIGHT HAND AND FOOT WILL BE. -
Page 18: Attaching The Front Bumper
Attaching the Front Bumper 1. TURN THE BODY UPSIDE DOWN SO THAT THE UNDERSIDE IS FACING UP. 2. FLIP THE FRONT BUMPER UPSIDE DOWN AND POSITION IT IN FRONT OF THE BODY SUCH THAT THE 7 PEGS AND 5 TABS IN THE BUMPER ARE ALIGNED WITH THE 7 PEG HOLES AND 5 TAB SLOTS IN THE BODY. - Page 19 4. FROM THE INSIDE OF THE BODY, INSERT 1 SCREW INTO EACH ALIGNED PEG HOLE AND PEG BY TWISTING IT IN CLOCKWISE. TIGHTEN EACH SCREW BY TWISTING IT CLOCKWISE WITH THE PHILLIPS-HEAD SCREWDRIVER. (7 TOTAL) 5. CHECK THAT THE FRONT BUMPER IS SECURED TO THE BODY. PEG IN PEG HOLE SCREW...
-
Page 20: Attaching The Rear Bumper
Attaching the Rear Bumper 1. FLIP THE REAR BUMPER UPSIDE DOWN AND POSITION IT IN FRONT OF THE BODY SUCH THAT THE 7 PEGS AND 6 TABS IN THE BUMPER ARE ALIGNED WITH THE 7 PEG HOLES AND 6 TAB SLOTS IN THE BODY. 2. - Page 21 3. FROM THE INSIDE OF THE BODY, INSERT 1 SCREW INTO EACH ALIGNED PEG HOLE AND PEG BY TWISTING IT IN CLOCKWISE. TIGHTEN EACH SCREW BY TWISTING IT CLOCKWISE WITH THE PHILLIPS-HEAD SCREWDRIVER. (7 TOTAL) 4. CHECK THAT THE REAR BUMPER IS SECURED TO THE BODY. PEG IN PEG HOLE REAR BUMPER (G)
-
Page 22: Attaching The Side Fenders
Attaching the Side Fenders 1. PLACE THE FENDERS ALONGSIDE THE BODY AS FOLLOWS: • FRONT LEFT FENDER ("K-L") AT THE FRONT OF THE BODY ON THE LEFT ("L") SIDE • FRONT RIGHT FENDER ("K-R") AT THE FRONT OF THE BODY ON THE RIGHT ("R") SIDE •... - Page 23 FRONT OF BODY FRONT FENDER (K-R) FRONT FENDER (K-L) TAB HOLE TAB HOLE RIGHT (R) SIDE OF BODY LEFT (L) SIDE OF BODY TAB HOLE TAB HOLE REAR FENDER (L-R) REAR FENDER (L-L) REAR OF BODY...
- Page 24 5. FROM THE INSIDE OF THE BODY, INSERT 1 SCREW INTO ALIGNED PEG HOLE AND PEG BY TWISTING IT IN CLOCKWISE. TIGHTEN EACH SCREW BY TWISTING IT CLOCKWISE WITH THE PHILLIPS-HEAD SCREWDRIVER. (4 TOTAL) 6. REPEAT STEPS 3 - 5 WITH THE OTHER FENDERS. 7.
- Page 25 FRONT OF BODY FRONT FENDER (K-R) FRONT FENDER (K-L) PHILLIPS-HEAD SCREWDRIVER SCREW PEG HOLE REAR FENDER (L-R) REAR FENDER (L-L) REAR OF BODY...
-
Page 26: Attaching The Steps
Attaching the Steps 1. PLACE THE LEFT STEP ("M-L") ON THE LEFT ("L") SIDE OF THE BODY AND THE RIGHT STEP ("M-R") ON THE RIGHT ("R") SIDE OF THE BODY. 2. WORKING WITH THE LEFT STEP, FLIP THE STEP UPSIDE DOWN SUCH THAT IT CURVES INTO THE FRAME AND THE TABS ARE ON THE EDGE CLOSER TO THE GROUND. - Page 27 TAB SLOT TAB SLOT STEP (M-R) STEP (M-L) PED HOLE PEG HOLE...
- Page 28 4. FROM THE INSIDE OF THE BODY, INSERT 1 SCREW INTO EACH ALIGNED PEG HOLE AND PEG BY TWISTING IT IN CLOCKWISE. TIGHTEN EACH SCREW BY TWISTING IT CLOCKWISE WITH THE PHILLIPS-HEAD SCREWDRIVER. (3 TOTAL) 5. REPEAT STEPS 2 - 4 WITH THE RIGHT STEP. 6.
- Page 29 LEFT (L) SIDE OF BODY RIGHT (R) SIDE OF BODY PHILLIPS-HEAD SCREWDRIVER SCREW STEP (M-R) STEP (M-L)
-
Page 30: Assembling The Front Axle
Assembling the Front Axle 1. USING A WRENCH, LOOSEN AND REMOVE THE LARGE NUTS FROM THE VERTICAL CONNECTORS ON THE FRONT AXLE BY TWISTING THEM OFF COUNTERCLOCKWISE. 2. SLIDE 1 WASHER OFF OF EACH SIDE OF THE AXLE, LEAVING 1 REMAINING ON THE AXLE. SET THE HARDWARE ASIDE. WRENCH LARGE NUT WASHER... - Page 31 FRONT AXLE STEERING BRACKET WASHER VERTICAL CONNECTOR FRONT OF BODY 3. CAREFULLY FLIP THE FRONT AXLE UPSIDE-DOWN (TAKING CARE THAT THE REMAINING WASHERS DO NOT FRONT SLIDE OFF OF THE VERTICAL CROSSBAR CONNECTORS) AND POSITION IT OVER THE BODY SUCH THAT: WASHER •...
- Page 32 7. CHECK THAT THE FRONT AXLE IS SECURED TO THE BODY.
-
Page 33: Attaching The Front Wheels
Attaching the Front Wheels 1. REMOVE THE LARGE NUT FROM EACH SIDE OF THE FRONT AXLE BY TWISTING IT OFF COUNTERCLOCKWISE. 2. REMOVE THE WASHER FROM EACH SIDE AND SET IT ASIDE WITH THE NUT. SET THE HARDWARE ASIDE. WASHER FRONT AXLE LARGE NUT WRENCH... - Page 34 3. LEADING WITH THE FLAT SIDE OF THE WHEEL, SLIDE ONE FRONT WHEEL ONTO EACH FRONT AXLE. 4. SLIDE A REMOVED WASHER BACK ONTO EACH SIDE OF THE AXLE. 5. TWIST A REMOVED LARGE NUT CLOCKWISE ONTO THE END OF EACH AXLE. USE THE WRENCH TO TIGHTEN THE NUTS ONTO THE AXLE.
- Page 35 6. LEADING WITH THE OPEN SIDE OF THE HUB CAB AND ALIGNING EACH OF THE 5 TABS ON THE HUBCAP WITH THE TAB SLOTS IN THE WHEEL, POP A HUBCAP INTO PLACE IN THE CENTER OF EACH REAR WHEEL OVER THE NUT. HUB CAP (Q) HUB CAP (Q) FRONT AXLE...
- Page 36 7. CHECK THAT THE WHEELS ARE SECURE ON THE AXLE AND THE HUB CAPS ARE SECURE ON THE WHEELS.
-
Page 37: Assembling The Rear Axle & Gear Boxes
Assembling the Rear Axle & Gear Boxes 1. LOOSEN AND REMOVE THE LARGE NUTS ON THE END OF THE REAR AXLE BY TWISTING THEM OFF COUNTERCLOCKWISE WITH THE WRENCH. 2. REMOVE THE WASHERS FROM THE AXLE. REAR AXLE (I) LARGE NUT WASHER WRENCH... - Page 38 REAR AXLE (I) REAR AXLE TUBE 3. FROM ONE SIDE OF THE BODY, SLIDE THE REAR AXLE THROUGH THE REAR AXLE TUBE.
- Page 39 RIGHT SIDE OF BODY LEFT SIDE OF BODY MOTOR WIRE REAR AXLE GEAR BOX GEAR BOX 4. LEADING WITH SIDE OF THE GEAR BOX WITH THE WIRES, SLIDE THE HOLE IN GEAR BOX MARKED "L" ONTO THE END OF THE REAR AXLE ON THE LEFT SIDE ("L") OF THE BODY MARKED. 5.
- Page 40 7. CHECK THAT THE GEAR BOXES ARE SNUG UP TO THE BODY AND THE WIRES FROM BOTH GEAR BOXES ARE FULLY INSIDE THE BODY.
-
Page 41: Attaching The Rear Wheels
REAR WHEEL REAR WHEEL WASHER REAR AXLE LARGE NUT WRENCH Attaching the Rear Wheels WRENCH 1. LEADING WITH THE SIDE OF THE WHEEL THAT HAS AN EXTENSION IN THE CENTER, SLIDE ONE REAR WHEEL ONTO EACH END OF THE AXLE. 2. - Page 42 HUB CAP (Q) HUB CAP (Q) 4. LEADING WITH THE OPEN SIDE OF THE HUB CAB AND ALIGNING EACH OF THE 5 TABS ON THE HUBCAP WITH THE TAB SLOTS IN THE WHEEL, POP A HUBCAP INTO PLACE IN THE CENTER OF EACH REAR WHEEL OVER THE NUT.
- Page 43 5. CHECK THAT THE WHEELS ARE SECURE ON THE AXLE AND THE HUB CAPS ARE SECURE ON THE WHEELS.
-
Page 44: Attaching The Dashboard
Attaching the Dashboard 2.10 DASHBOARD (C) RIDER AREA 1. TURN THE BODY RIGHT SIDE UP. 2. OPEN BOTH DOORS. 3. POSITION THE WINDSHIELD OVER THE FRONT OF THE BODY SUCH THAT THE WIRES ARE HANGING DOWN AND THE CONTROL BOARD IS FACING THE RIDER AREA. - Page 45 8. POSITION THE DASHBOARD ON THE FRAME SUCH THAT THE 4 TABS ON THE DASHBOARD ARE ALIGNED WITH THE 4 TAB HOLES IN THE FRAME. 9. TILT THE DASHBOARD FORWARD AT A 15 - 20° TO INSERT THE TABS IN THE HOLES, AND THEN TILT THE DASHBOARD BACK TO POP IT INTO PLACE ON THE BODY.
-
Page 46: Assembling The Steering Rod
Assembling the Steering Rod 2.11 1. FLIP THE BODY ONTO ONE SIDE. 2. WITH THE HOOK ANGLED TOWARDS THE CENTER OF THE FRONT OF THE BODY, SLIDE THE STRAIGHT END OF THE STEERING ROD THROUGH THE CHANNEL IN THE FRONT AXLE TAB, THROUGH THE HOLE IN THE STEERING TUBE CAP, AND INTO THE STEERING TUBE. - Page 47 3. SLIDE THE STEERING ROD INTO THE TUBE UNTIL THE CROSSBAR NESTLES IN THE STEERING TUBE CAP, GUIDING THE HOOK OF THE STEERING TUBE INTO THE HOLE OF THE STEERING BRACKET TAB. STEERING BRACKET STEERING ROD CROSSBAR STEERING BRACKET STEERING ROD (J) STEERING TUBE STEERING TUBE...
- Page 48 4. SLIDE A WASHER ON THE END OF THE ROD THAT IS HOOKED THROUGH THE TAB. 5. SECURE THE ROD IN PLACE BY INSERTING THE STRAIGHT END OF A PIN THROUGH BOTH THE HOLE IN THE ROD. WASHER STEERING ROD STEERING BRACKET TAB...
- Page 49 6. TURN YOUR ATTENTION TO THE STRAIGHT END OF THE STEERING ROD ON THE INSIDE OF THE FRAME NEAR THE RIDER AREA. LOOK FOR THE HOLE IN THE STEERING ROD NEAR THE INSERTION POINT. NOTE: IF YOU CANNOT SEE THE HOLE, TRY PUSHING THE ROD IN A LITTLE MORE FROM THE UNDERSIDE OF THE BODY.
-
Page 50: Attaching The Steering Wheel
Attaching the Steering Wheel 2.12 1. USE YOUR FINGER TO HOLD THE NUT IN THE STEERING WHEEL POST STEADY WHILE YOU USE THE PHILLIPS-HEAD SCREWDRIVER TO LOOSEN AND REMOVE THE BOLT OPPOSITE IT BY TURNING THE BOLT COUNTERCLOCKWISE. SET THE HARDWARE ASIDE. - Page 51 2. SLIDE THE STEERING WHEEL POST INTO THE STEERING TUBE SO THAT THE CHANNEL ON THE POST FITS INTO THE CHANNEL ON THE INSIDE OF THE TUBE, AND THE HOLES IN THE SIDE OF THE POST AND TUBE ARE ALIGNED. STEERING WHEEL STEERING WHEEL POST STEERING TUBE...
- Page 52 3. FROM THE RIGHT SIDE, SLIDE THE REMOVED BOLT THROUGH THE ALIGNED HOLES ON THE RIGHT OF THE STEERING WHEEL POST UNTIL THE TIP EMERGES THROUGH THE ALIGNED HOLES ON THE LEFT. 4. TWIST THE NUT CLOCKWISE ONTO THE END OF THE BOLT. 5.
-
Page 53: Inserting The Seat Base
Inserting the Seat Base 2.13 1. POSITION THE SEAT BASE OVER THE BATTERY COMPARTMENT SUCH THAT THE FOLLOWING CONDITIONS ARE MET: • THE SMOOTH SIDE OF THE SEAT BASE IS FACING UP • THE 4 TABS AT THE BACK OF THE SEAT BASE ARE ALIGNED WITH THE 4 TAB SLOTS AT THE BACK OF THE BATTERY COMPARTMENT IN THE BODY OF THE SAFARA MAX. -
Page 54: Attaching The Seats
Attaching the Seats 2.14 1. ALIGN ONE SEAT OVER ONE SIDE OF THE SEATING AREA. ENSURE THAT THE SEATBELT STRAPS ARE NOT SEAT DANGLING BELOW THE SEAT. 2. TILT THE SEAT SLIGHTLY TO FIT THE TAB IN THE BACK OF THE SEAT INTO THE TAB INSERT AT THE REAR OF THE SEATING AREA. - Page 55 4. REPEAT WITH THE SECOND SEAT.
- Page 56 5. ROTATE THE SEAT LOCK ON EACH SEAT CLOCKWISE WITH A FLATHEAD SCREWDRIVER (INCLUDED WITH B MODELS) TO SECURE THE SEATS IN PLACE. SEAT LOCK 6. CHECK THAT EACH SEAT IS SECURELY AFFIXED AND DOES NOT MOVE. FLAT-HEAD SCREWDRIVER...
-
Page 57: Attaching The Side Mirrors
Attaching the Side Mirrors 2.15 RIGHT SIDE MIRROR (E) RIGHT SIDE OF BODY 1. POSITION THE SIDE MIRRORS ON THE SIDE OF THE WINDSHIELD SUCH THAT THE MIRROR SIDE IS FACING THE RIDER AND THE SIDE WITH THE STEM IS CLOSEST TO THE WINDSHIELD. - Page 58 3. CHECK THAT THE SIDE MIRRORS ARE SECURE IN THE BODY.
-
Page 59: Attaching The Rear Tailstock
Attaching the Rear Tailstock 2.16 1. SLIDE ONE END OF THE REAR TAILSTOCK ROD INTO THE ROD HOLES ON BOTH THE LEFT AND RIGHT FRAME PIECES OF THE TAILSTOCK. REAR TAILSTOCK RIGHT SIDE FRAME (R) REAR TAILSTOCK LEFT SIDE FRAME (R) REAR TAILSTOCK ROD (R) - Page 60 2. POSITION THE TAILSTOCK OVER THE REAR OF THE BODY SUCH THAT THE 4 PINS ARE FACING FORWARD AND THE 4 TAILSTOCK LEGS ARE OVER THE 4 HOLES AT THE REAR OF THE BODY. 3. PRESS AND HOLD EACH OF THE PINS IN WHILE YOU PUSH THE LEGS INTO THE HOLES AND UNTIL THE PINS POP OUT ON THE UNDERSIDE OF THE HOLES (INSIDE THE BODY.) TAILSTOCK LEG REAR OF BODY...
- Page 61 4. CHECK THAT THE REAR TAILSTOCK IS SECURED TO THE BODY.
-
Page 62: Making Moves
3. Making Moves Fastening the Seatbelts POSITION BOTH STRAPS OF THE SEATBELT ON EACH SEAT OVER THE LAP OF THE RIDER. CLICK THE INSERTION CLIP INTO THE RECEIVING CLIP. CHECK THAT THE BELT IS SECURE AND SNUG OVER THE RIDER'S LAP. IF NECESSARY, SHORTEN OR LENGTHEN THE BELT BY MOVING THE ADJUSTMENT SLIDE BUCKLE ALONG THE STRAP. -
Page 63: Using The Remote Control
Using the Remote Control THE REMOTE CONTROL NEEDS TO BE PAIRED WITH THE VEHICLE UPON FIRST USE AND AFTER EVERY BATTERY REPLACEMENT. THEN, USE THE BUTTONS ON THE REMOVE TO CONTROL THE VEHICLE SPEED (FAST, SLOW, OR PARK/STOP), DIRECTION (FORWARD, REVERSE, LEFT, AND RIGHT). ONCE THE REMOTE CONTROL IS PAIRED AND WHENEVER IT IS BEING USED, IT WILL TAKE OVER CONTROL OF THE SAFARA. - Page 64 TO INSERT BATTERIES IN THE REMOTE CONTROL: 1. LOOSEN THE SCREW ON THE BATTERY COMPARTMENT ON THE BACK SIDE OF THE REMOTE CONTROL BY TWISTING THE SCREW COUNTERCLOCKWISE WITH THE PHILLIPS-HEAD SCREWDRIVER. 2. LIFT UP THE COMPARTMENT COVER. 3. PLACE 2 AAA BATTERIES AS DIRECTED BY THE +/- MARKINGS IN THE COMPARTMENT. 4.
-
Page 65: Activating Horn & Engine Sounds
Activating Horn & Engine Sounds PUSH THE BUTTONS ON THE STEERING WHEEL TO MAKE HORN AND ENGINE SOUNDS. NOTE: INSERTING BATTERIES IN THE STEERING WHEEL WILL ONLY ALLOW THE RIDER TO MAKE USER OF THE HORN AND ENGINE SOUNDS. THEY ARE NOT NECESSARY FOR RIDING. BATTERY COMPARTMENT HORN SOUND ENGINE SOUNDS... - Page 66 TO INSERT BATTERIES IN THE STEERING WHEEL: 1. LOOSEN THE SCREW ON THE BATTERY COMPARTMENT BY TWISTING THE SCREW COUNTERCLOCKWISE WITH THE PHILLIPS-HEAD SCREWDRIVER. 2. LIFT UP THE COMPARTMENT COVER. 3. PLACE 2 AAA BATTERIES AS DIRECTED BY THE +/- MARKINGS IN THE COMPARTMENT. 4.
-
Page 67: A Guide To Your Dashboard & Controls
A Guide to Your Dashboard & Controls USE THE BUTTONS AND SWITCHES ON THE DASHBOARD TO POWER THE SAFARA MAX ON OR OFF, TURN ON OR OFF THE HEADLIGHT, SWITCH FROM FAST TO SLOW, AND CHANGE DIRECTIONS FROM FORWARD TO REVERSE. POWER FAST &... -
Page 68: Charging The Safara Max
Charging the Safara Max IMPORTANT: BEFORE FIRST USE, CHARGE THE BATTERY 15 TO 18 HOURS. AFTER THAT, AND FOR REGULAR CHARGING SESSIONS, CHARGE ONLY TO A FULL BATTERY: ABOUT 8 TO 12 HOURS. 1. PLUG THE CHARGER INTO THE WALL, AND THEN PLUG THE CHARGER CORD INTO THE CHARGING PORT. - Page 69 IMPORTANT CHARGING NOTES: · ONLY USE THE INCLUDED CHARGER OR ONE OBTAINED DIRECTLY THROUGH JETSON LABELED WITH: SL12-07-02 FAILURE TO USE CORRECT CHARGER CAN RESULT IN FIRE AND EXPLOSION. · ALWAYS KEEP THE CHARGING PORT CLOSED WHEN NOT ACTIVELY CHARGING THE BATTERY.
-
Page 70: Helmet Safety
Helmet Safety A HELMET SHOULD BE WORN BY THE RIDER(S) AT ALL TIMES. PROPER POSITIONING: IMPROPER POSITIONING: THE FOREHEAD IS COVERED THE FOREHEAD IS EXPOSED. BY THE HELMET. A FALL COULD RESULT IN SERIOUS INJURY. * WEAR A HELMET, APPROPRIATE CLOTHING, SHOES, AND SAFETY GEAR. AVOID CLOTHING THAT CAN GET CAUGHT INTO OR UNDER THE WHEELS. -
Page 71: Care & Maintenance
WATER DIRECTLY TO THE PRODUCT, AS THE ELECTRICAL AND ELECTRONIC SYSTEMS MAY GET WET, WHICH COULD LEAD TO A MALFUNCTION THAT PUTS RIDER SAFETY AT RISK. · IF THE ELECTRIC PARTS OR BATTERY GET WET, DO NOT POWER ON THE SAFARA MAX. CONTACT THE JETSON CARE TEAM FOR ASSISTANCE. STORING THE SAFARA MAX ·... - Page 73 Stay connected. Be sure to follow @ridejetson on social media to learn about fantastic offers, giveaways, and all the latest Jetson news. Loving your ride? Then be sure to leave a review at ridejetson.com/reviews. We can’t wait to hear from you!
- Page 76 Date Code: 06/2023 Document Edition: v2.0 © 2023, JETSON. ALL RIGHTS RESERVED. Manufactured by JETSON ELECTRIC BIKES LLC. No portion of this document, including shape, copy, graphics, and design, may be reproduced or transmitted in any form or by any means.