Related Manuals for Jetson Safara
Summary of Contents for Jetson Safara
- Page 1 Safara Electric Ride-On. A guide for your ride. IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY MODEL: JSAFAR-RED Designed in Brooklyn | Made in China...
- Page 3 Remember to be safe and, most importantly, have fun!
-
Page 5: Table Of Contents
...................4 5 Powering the Safara ......................47 Using the Remote Control .. -
Page 6: Safety Warnings
Safety Warnings • Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use. • Before each cycle of operation, the operator shall perform the preoperation checks specified by the manufacturer: That all guards and pads originally supplied by the manufacturer are in proper place and in serviceable condition;... - Page 7 For more information go to www.p65warnings.ca.gov/product MODIFICATIONS Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without instruction from Jetson Customer Care. This will void any warranty, and can lead to malfunctions which may cause injury.
-
Page 8: What's In The Box
What’s in the Box 1. BODY 10. STEERING BRACKET (A) 2. SEAT 11. STEERING BRACKET (B) 3. SEAT BACK 12. REAR AXLE 4. REAR TAILSTOCK 13. FRONT WHEEL (2X) 5. STEERING WHEEL 14. REAR WHEEL (DRIVER WHEEL) (2X) 6. WINDSHIELD 15. - Page 9 PLEASE NOTE: IMAGES MAY NOT REFLECT EXACT APPEARANCE OF ACTUAL PRODUCT.
-
Page 11: Specs & Features
Specs & Features • MAX SPEED: UP TO 3.5 MPH • MAX RANGE: UP TO 3.5 MILES • BATTERY: RECHARGEABLE 12V, 7AH • REMOTE CONTROLLER BATTERIES: 2 AAA BATTERIES • STEERING WHEEL BATTERIES: 2 AA BATTERIES • MOTOR: 40W × 2 •... -
Page 12: Initial Assembly
1. Get Started Initial Assembly • FLIP THE CAR OVER SO THAT THE BOTTOM IS FACING UPWARDS. • RELEASE THE STEERING BRACKET (B) AT THE FRONT OF THE CAR BY CUTTING OFF THE ZIP TIES AND UNSCREWING THE NUT USING WRENCH ON THE CENTER HOOK.. ZIP TIE STEERING BRACKET (B) - Page 13 • CAREFULLY REMOVE THE STEERING BRACKET (B) AND SET ASIDE UNTIL REQUIRED. STEERING BRACKET (B)
- Page 14 • UNSCREW THE SCREWS AND NUTS ON BOTH ENDS OF THE STEERING BRACKET (B). • SET SCREWS AND NUTS TO ONE SIDE UNTIL REQUIRED. SCREW...
- Page 15 • STRAIGHTEN THE FRONT WHEEL AXLE FROM STEERING BRACKET (A). STEERING BRACKET (A)
- Page 16 •PLACE THE STEERING BRACKET (B) BACK. STEERING BRACKET (B)
- Page 17 • PLACE NUT ON CENTER HOOK AND TIGHTEN USING WRENCH.
- Page 18 • PLACE SCREW AND NUT ON BOTH END OF STEERING BRACKET (B). TIGHTEN USING SCREWDRIVER. • MAKE SURE THE STEERING BRACKET (B) IS NOW SECURELY ATTACHED.
-
Page 19: Assembling The Rear Wheels
BACKSHAFT BASE Assembling the Rear Wheels • IN THE REAR OF THE CAR, PLACE THE TWO BACKSHAFT BASES INTO THEIR CORRESPONDING HOLDER. - Page 20 BACKSHAFT BASE • MAKE SURE THAT THE BACKSHAFT MARKED R IS PLACED ON THE SIDE OF THE CAR MARKED R AND THAT THE BACKSHAFT MARKED L IS PLACED ON THE SIDE OF THE CAR MARKED L.
- Page 21 • SECURE BOTH BACKSHAFT WITH SCREWS (10X - 5X PER SIDE) USING SCREWDRIVER. • MAKE SURE THAT THEY ARE SECURELY ATTACHED.
- Page 22 • LOOSEN AND TAKE OUT WASHER AND NUT FROM EACH END OF REAR AXLE. • SET ASIDE NUT AND WASHER UNTIL REQUIRED. REAR AXLE...
- Page 23 REAR AXLE • INSERT REAR AXLE THROUGH THE HOLES IN THE BACKSHAFT BASE.
- Page 24 GEAR BOX • INSERT GEAR BOXES ONTO REAR AXLE. • MAKE SURE THE GEAR BOX MARKED R IS INSERTED ONTO THE R SIDE OF THE CAR AND THE GEAR BOX MARKED L IS INSERTED ONTO THE L SIDE OF THE CAR. *ATTACH WITH CAUTION.
- Page 25 • PLACE WIRES FROM GEAR BOX INTO CORRESPONDING HOLE ON SIDE OF THE CAR.
- Page 26 REAR WHEEL (DRIVER WHEEL) • PLACE REAR WHEELS ONTO REAR AXLE.
- Page 28 • PLACE WASHER AND THEN NUT ONTO BOTH SIDES OF THE REAR AXLE. TIGHTEN USING WRENCH. • MAKE SURE THAT EACH WHEEL IS SECURELY ATTACHED. *SCREWING BOLTS TOO TIGHT CAN CRACK WHEEL.
- Page 29 HUB CAP • PLACE HUB CAP OVER NUT AND WASHER. SECURE IN PLACE.
-
Page 30: Assembling The Front Wheels
Assembling the Front Wheels • REMOVE 1 WASHER AND 1 NUT FROM EACH END OF THE FRONT WHEEL AXLE FROM STEERING BRACKET (A). • THERE SHOULD BE 1 WASHER REMAINING ON EACH SIDE OF THE AXLE. STEERING BRACKET (A) - Page 32 • INSERT FRONT WHEELS ONTO THE FRONT WHEEL AXLE. FRONT WHEEL...
- Page 34 • PLACE WASHER AND THEN NUT ONTO BOTH SIDES OF THE FRONT AXLE. TIGHTEN USING WRENCH. • MAKE SURE THAT EACH WHEEL IS SECURELY ATTACHED. *SCREWING BOLTS TOO TIGHT CAN CRACK WHEEL.
- Page 35 • PLACE HUB CAP OVER NUT AND WASHER. SECURE IN PLACE. HUB CAP...
-
Page 36: Inserting The Seat
Inserting the Seat • FLIP THE CAR BACK OVER SO IT IS UPRIGHT. • BEFORE YOU INSERT THE SEAT, CONNECT THE WIRES IN THE BOX. NOTE: MAKE SURE TO CONNECT EACH WIRE BOX WITH ITS CORRESPONDING COLOR. - Page 38 • INSERT SEAT BACK INTO SAFARA BODY. • ONCE THE SEAT BACK IS IN POSITION, INSERT THE SEAT. SEAT BACK SEAT...
- Page 40 CHAIR SEAT BACK • WITH SCREWDRIVER, SECURE SEAT AND SEAT BACK INTO PLACE USING SCREWS (4X). • MAKE SURE THAT IT IS SECURELY ATTACHED.
-
Page 41: Inserting The Rear Tailstock
Inserting the Rear Tailstock • INSERT REAR TAILSTOCK INTO CORRESPONDING HOLES IN SAFARA BODY. • SNAP REAR TAILSTOCK INTO PLACE. REAR TAILSTOCK... - Page 42 • MAKE SURE REAR TAILSTOCK IS SECURELY ATTACHED.
-
Page 43: Inserting The Steering Wheel
Inserting the Steering Wheel • INSERT STEERING WHEEL INTO STEM POST. • SNAP STEERING WHEEL INTO PLACE. STEERING WHEEL... - Page 44 • MAKE SURE STEERING WHEEL IS SECURELY ATTACHED.
- Page 45 Attaching the Windshield • ALIGN WINDSHIELD WITH WINDSHIELD HOLES. • WINDSHIELD POPS INTO PLACE. WINDSHIELD...
- Page 46 • WITH SCREWDRIVER, SCREW WINDSHIELD INTO PLACE USING SCREWS (2X). • MAKE SURE THE WINDSHIELD IS SECURELY ATTACHED.
-
Page 47: Inserting The Rearview Mirrors
Inserting the Rearview Mirrors • INSERT LEFT SIDE REARVIEW MIRROR INTO LEFT SIDE MIRROR BASE. • INSERT RIGHT SIDE REARVIEW MIRROR INTO RIGHT SIDE MIRROR BASE. REARVIEW MIRRORS... - Page 48 • MAKE SURE REARVIEW MIRRORS ARE SECURELY ATTACHED.
-
Page 49: Powering The Safara
Powering the Safara • UNCLIP HOOD LOCK ON BOTH SIDES OF THE HOOD. • OPEN THE HOOD. HOOD HOOD LOCK... - Page 50 • PLUG IN THE POWER CORD, ENSURE CLIPS ARE THE SAME COLOR.
-
Page 51: Using The Remote Control
1. PRESS AND HOLD THE MATCH BUTTON FOR 2 TO 4 SECONDS. THE LED LIGHTS WILL FLASH. 2. TURN THE SAFARA ON. THE LIGHTS WILL TURN SOLID TO INDICATE A SUCCESSFUL LINK. 3. IF THE LIGHTS CONTINUE TO FLASH THAT MEANS AN UNSUCCESSFUL LINK. REMOVE AND REINSERT... -
Page 52: Using The Steering Wheel
Using the Steering Wheel BATTERY COMPARTMENT ENGINE SOUNDS HORN • USING SCREWDRIVER, UNSCREW BATTERY COMPARTMENT. • INSERT 2 AA BATTERIES INTO BATTERY COMPARTMENT. • SCREW BATTERY COMPARTMENT BACK INTO PLACE. - Page 53 A Guide to Your Dashboard FAST SLOW POWER FAST & SLOW SWITCH SWITCH FORWARD, STOP & REVERSE...
-
Page 54: Charging The Safara
CHARGING PORT • INSERT CHARGER INTO CHARGING PORT AND INSERT PLUG INTO A WALL OUTLET. • CHARGE THE BATTERY 15 TO 18 HOURS BEFORE RIDING SAFARA FOR THE FIRST TIME. • DO NOT CHARGE THE BATTERY FOR MORE THAN 20 HOURS. -
Page 55: Helmet Safety
Helmet Safety THE FOREHEAD IS COVERED THE FOREHEAD IS EXPOSED. BY THE HELMET. COULD CAUSE SERIOUS INJURY. -
Page 56: Care & Maintenance
Care & Maintenance CLEANING THE SAFARA TO CLEAN THE SAFARA, CAREFULLY WIPE WITH A DAMP CLOTH, THEN DRY WITH A DRY CLOTH. DO NOT USE WATER TO CLEAN THE SAFARA, THIS MAY DAMAGE THE FRAME OR SEAT. STORAGE • STORE THE SAFARA INDOORS IN A DRY PLACE. - Page 57 Enjoying the ride? Leave a review on ridejetson.com/reviews or share your photos with us online using the #RideJetson hashtag! Follow us @ridejetson #MakeMoves...
- Page 58 Questions? Let us know. support.ridejetson.com Hours of Operation: 7 Days a Week, 10am-6pm Manufactured by Zhejiang, China Imported by Jetson Electric Bikes LLC. 86 34th Street 4th Floor, Brooklyn, New York 11232 www.ridejetson.com Made in China Date Code: 08/2021...