Related Manuals for Jetson Safara Max
Summary of Contents for Jetson Safara Max
- Page 1 Safara Max Electric Ride-On. A guide for your ride. IMPORTANT: READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE. MODEL: JSAFX-NAV Designed in Brooklyn | Made in China...
- Page 3 Jetson's top two riding rules: Be safe. Have fun!
-
Page 5: Table Of Contents
....................50 A Guide to Your Dashboard ....................5 1 Charging the Safara Max ....................5 2 Helmet Safety . -
Page 6: Safety Warnings
Safety Warnings • Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use. • Please check the drive system and frame before riding to ensure safety. •... - Page 7 • Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death. • If the brake loosens, please adjust with the hexagon wrench, or please contact the Jetson Care Team. • Replace worn or broken parts immediately.
- Page 8 For all maintenance repairs and needs beyond the capability of the consumer, which may include but not be limited to: such as proper maintenance of brakes, control cables, bearing adjustments, wheel adjustments, lubrication, reflectors, tires and handlebar and seat adjustments, please contact the Jetson Care Team for assistance at: ridejetson.com/support US &...
-
Page 9: Specs & Features
All new Jetson products, excluding parts and accessories, are warranted against defects in materials and workmanship for a period of one year from the date of original retail purchase when used in accordance with Jetson's user manuals (refer to ridejetson.com/support). -
Page 10: What's In The Box
What’s in the Box K. FRONT FENDER (2X) A. BODY B. SEAT WITH SEATBELT (2X) L. REAR FENDER (2X) C. DASHBOARD M. STEP (2X) D. STEERING WHEEL N. GEAR BOX (2X) E. SIDE MIRROR (2X) O. FRONT WHEEL (2X) F. FRONT BUMPER P. - Page 11 PLEASE NOTE: IMAGES MAY NOT REFLECT EXACT APPEARANCE OF ACTUAL PRODUCT.
-
Page 12: Front Bumper Assembly
1. Getting Started Front Bumper Assembly • TURN THE VEHICLE BODY UPSIDE-DOWN. • AFFIX THE FRONT BUMPER ALONG THE FRONT OF THE VEHICLE BODY. ALIGN AND INSERT EACH OF THE 7 PEGS INTO THE 7 SCREWHOLES AND EACH OF THE 5 TABS INTO THE TAB INSERTS. FRONT BUMPER (F) PEGS SCREW HOLES... - Page 13 • INSERT 7 SCREWS AND TIGHTEN WITH THE SCREWDRIVER. SCREW...
-
Page 14: Fear Bumper Assembly
Rear Bumper Assembly • AFFIX THE REAR BUMPER ALONG THE BACK OF THE VEHICLE BODY. ALIGN AND INSERT EACH OF THE 5 PEGS WITH THE 5 SCREW HOLES AND EACH OF THE 6 TABS WITH THE 6 TAB INSERTS. REAR BUMPER (G) PEGS SCREW HOLES TAB INSERTS... - Page 15 • INSERT 5 SCREWS AND TIGHTEN WITH THE SCREWDRIVER. SCREW...
-
Page 16: Side Fenders Assembly
Side Fenders Assembly • AFFIX EACH FENDER ALONG THE SIDE EDGES OF THE VEHICLE BODY, ALIGNING WITH SCREW HOLES. FRONT FENDER (K) FRONT FENDER (K) REAR FENDER (L) REAR FENDER (L) - Page 17 • THERE ARE 4 FENDERS TOTAL. FOR EACH FENDER, INSERT 4 SCREWS AND TIGHTEN WITH A SCREWDRIVER. FRONT FENDER (K) FRONT FENDER (K) SCREW REAR FENDER (L) REAR FENDER (L)
-
Page 18: Steps Assembly
Steps Assembly • AFFIX EACH STEP ALONG THE SIDE EDGES OF THE VEHICLE BODY, ALIGNING AND INSERTING EACH OF THE 3 TABS AND ALIGNING THE 3 SCREW HOLES. STEP (M) STEP (M) - Page 19 • FOR EACH STEP, INSERT 3 SCREWS AND TIGHTEN WITH A SCREWDRIVER. SCREW STEP (M) STEP (M)
-
Page 20: Front Axle Assembly
Front Axle Assembly • THE TWO ARMS ON THE FRONT AXLE EACH HAVE 2 WASHERS AND 1 NUT PRE-ATTACHED. REMOVE 1 WASHER AND THE NUT FROM EACH ARM. FRONT AXLE (H) - Page 21 • PLACE THE ARMS INTO THE MATCHING HOLES ON THE FRONT END OF THE VEHICLE BODY AND FASTEN THE WASHER AND NUT ON EACH ARM USING THE WRENCH.
- Page 22 • MAKE SURE THE ARM IS SECURELY ATTACHED.
-
Page 23: Front Wheel Assembly
Front Wheel Assembly • ON THE FRONT WHEEL AXLE, REMOVE THE PRE-ATTACHED WASHERS AND NUTS USING THE WRENCH ON BOTH SIDES. - Page 24 • ALIGN THE FRONT WHEELS WITH THE ENDS OF THE FRONT AXLE, ENSURING THAT THE FLAT SIDE OF EACH WHEEL IS ON THE INSIDE NEAR THE VEHICLE BODY. SLIDE WASHER AND THEN NUT ONTO EACH END OF THE AXLE, AND USE THE WRENCH TO TIGHTEN THE NUTS.
- Page 25 • ALIGN AND POP ON THE HUB CAP. THE TIRE SHOULD ROTATE EASILY. • REPEAT ON THE OTHER SIDE. • STRAIGHTEN THE FRONT WHEEL AXLE. HUB CAP (Q) HUB CAP (Q)
- Page 26 • MAKE SURE EVERYTHING IS SECURELY ATTACHED.
-
Page 27: Rear Axle Assembly
Rear Axle Assembly • REMOVE PRE-ATTACHED WASHER AND NUT FROM EACH SIDE OF THE REAR AXLE. SET ASIDE FOR STEP 1.8 (REAR TIRE ASSEMBLY). REAR AXLE (I) - Page 28 REAR AXLE (I) REAR AXLE TUBE • FROM ONE SIDE OF THE VEHICLE BODY, SLIDE THE REAR AXLE INTO THE REAR AXLE TUBE.
- Page 29 GEAR BOX (N) GEAR BOX (N) • ALIGN THE GEAR BOX MARKED “R” ON THE RIGHT SIDE OF THE VEHICLE (VEHICLE BODY IS MARKED WITH “R” AND “L” - BE SURE TO MATCH WITH THE CORRECT SIDE). • SLIDE THE HOLE IN THE GEAR BOX ONTO THE END OF THE REAR AXLE. •...
- Page 30 • MAKE SURE THAT THE GEAR BOXES ARE SECURELY ATTACHED.
-
Page 31: Rear Wheel Assembly
REAR WHEEL (P) REAR WHEEL (P) Rear Wheel Assembly • ALIGN THE REAR WHEELS WITH THE ENDS OF THE REAR AXLE, ENSURING THAT THE FLAT SIDE OF EACH WHEEL IS ON THE INSIDE NEAR THE VEHICLE BODY. SLIDE WASHER AND THEN NUT ONTO EACH END OF THE AXLE, AND USE THE WRENCH TO TIGHTEN THE NUTS. - Page 32 HUB CAP (Q) HUB CAP (Q) • ALIGN AND POP ON THE HUB CAP. THE TIRE SHOULD ROTATE EASILY. • REPEAT ON THE OTHER SIDE.
- Page 33 • MAKE SURE EVERYTHING IS SECURELY ATTACHED.
-
Page 34: Dashboard Assembly
Dashboard Assembly DASHBOARD (C) • TURN THE VEHICLE BODY RIGHT SIDE UP. • OPEN THE DOORS ON BOTH SIDES. • ALIGN THE DASHBOARD ALONG THE FRONT OF THE VEHICLE WITH A 15°-20° ANGLE AND CONNECT 4 SETS OF WIRES. • CLICK EACH ELECTRICAL CONNECTOR ON THE DASHBOARD INTO THE ONE INSIDE THE BODY OF THE VEHICLE WHOSE WIRES MATCH IN COLOR. - Page 35 • INSERT 2 SCREWS, ONE ON EITHER SIDE, AND TIGHTEN WITH THE SCREWDRIVER. • CHECK TO MAKE SURE THAT THE DASHBOARD IS SECURELY FASTENED TO THE VEHICLE BODY.
-
Page 36: Steering Rod Assembly
Steering Rod Assembly 1.10 • FLIP THE VEHICLE ONTO ITS SIDE. • INSERT J-SHAPED STEERING ROD INTO THE GEAR BOX, WITH THE HOOK TURNED TOWARDS THE FRONT OF THE VEHICLE BODY. STEERING ROD (J) - Page 37 • HOOK THE TOP OF THE ROD ONTO THE TAB ON THE FRONT AXLE.
- Page 38 • SLIDE A WASHER ON THE END OF THE ROD THAT IS HOOKED THROUGH THE TAB. • SECURE THE ROD IN PLACE BY INSERTING THE STRAIGHT END OF A PIN THROUGH BOTH HOLES OF THE ROD. WASHER...
- Page 39 • TURN THE VEHICLE BODY RIGHT SIDE UP. • INSERT THE STRAIGHT END OF THE PIN THROUGH BOTH HOLES IN THE STEERING ROD TO SECURE IT IN PLACE FOR ASSEMBLY OF THE STEERING WHEEL.
-
Page 40: Steering Wheel Assembly
Steering Wheel Assembly 1.11 • USE THE SCREWDRIVER TO REMOVE THE PRE-ATTACHED NUT AND BOLT FROM THE STEERING WHEEL . STEERING WHEEL (D) (PRE-ATTACHED ON THE OTHER SIDE OF THE STEERING WHEEL) BOLT... - Page 41 • AFFIX THE STEERING WHEEL ONTO THE STEERING TUBE SO THAT THE END OF THE STEERING ROD IS INSIDE. • ROTATE THE STEERING WHEEL SO THAT THE HOLES AT THE BASE OF IT ARE ALIGNED WITH THE HOLES ON THE STEERING ROD.
- Page 42 • INSERT BOLT THROUGH ALL FOUR HOLES. FASTEN A NUT ON THE END OF THE BOLT AND TIGHTEN THE BOLT WITH THE SCREWDRIVER. • REMOVE THE PIN IN THE STEERING ROD. • CHECK THAT TURNING THE STEERING WHEEL TURNS THE FRONT WHEELS. BOLT...
-
Page 43: Dual Seats Assembly
Dual Seats Assembly 1.12 • ALIGN ONE SEAT OVER ONE SIDE OF THE SEATING AREA. • TILT THE SEAT SLIGHTLY TO FIT THE TAB IN THE BACK OF THE SEAT INTO THE TAB INSERT AT THE REAR OF THE SEATING AREA. •... - Page 44 • REPEAT WITH THE SECOND SEAT.
- Page 45 • CHECK THAT EACH SEAT IS SECURELY AFFIXED AND DOES NOT MOVE.
-
Page 46: Side Mirrors Assembly
Side Mirrors Assembly 1.13 • INSTALL SIDE MIRRORS BY INSERTING THE ROD ON THE BOTTOM OF EACH MIRROR INTO THE CORRESPONDING HOLES ON THE VEHICLE BODY. • POP THE MIRRORS DOWN INTO PLACE. SIDE MIRROR (E) - Page 47 • CHECK THAT EACH MIRROR IS SECURELY AFFIXED AND DOES NOT MOVE.
-
Page 48: Rear Tailstock Assembly
Rear Tailstock Assembly 1.14 • INSERT THE STRAIGHT ROD INTO EACH CURVED PIECE. REAR TAILSTOCK SIDE FRAME (R) REAR TAILSTOCK ROD (R) - Page 49 • AFFIX THE TAILSTOCK ONTO VEHICLE BODY, ALIGNING EACH OF THE 4 LEGS WITH THE HOLES ON THE 4 CORNERS AROUND THE SEATS. • WHILE PRESSING IN THE PUSH PIN ON EACH LEG, SLIDE EACH LEG DOWN INTO THE HOLES OF THE VEHICLE BODY UNTIL THE PIN POPS OUT ON THE UNDERSIDE OF THE HOLE, SECURING THE REAR TAILSTOCK IN PLACE.
- Page 50 • CHECK THAT THE FRAME IS SECURELY AFFIXED AND DOES NOT MOVE.
-
Page 51: Using The Remote Control
1. PRESS AND HOLD THE MATCH BUTTON FOR 2 TO 4 SECONDS. THE LED LIGHTS WILL FLASH. 2. TURN THE SAFARA MAX ON USING THE POWER SWITCH ON THE VEHICLE DASHBOARD. (SEE PAGE 51 OF THIS MANUAL.) THE LIGHTS WILL TURN SOLID TO INDICATE THAT THE PAIRING WAS SUCCESSFUL. -
Page 52: Using The Steering Wheel
Using the Steering Wheel BATTERY COMPARTMENT HORN ENGINE SOUNDS • USING THE SCREWDRIVER, UNSCREW THE BATTERY COMPARTMENT COVER. • INSERT 2 AA BATTERIES INTO THE BATTERY COMPARTMENT. • SCREW THE BATTERY COMPARTMENT COVER BACK INTO PLACE. -
Page 53: A Guide To Your Dashboard
A Guide to Your Dashboard FAST & SLOW SWITCH POWER SWITCH LIGHTS ACCELERATOR PEDAL FORWARD & REVERSE • ENGAGE THE ACCELERATOR PEDAL UNDERNEATH THE DASHBOARD TO MOVE THE SAFARA MAX. • EASE BACK ON THE PEDAL TO SLOW DOWN OR STOP. -
Page 54: Charging The Safara Max
Charging the Safara Max CHARGING INSTRUCTIONS AND INFORMATION • THE CHARGING PORT IS LOCATED UNDER THE DRIVER’S SEAT. • PLUG THE CHARGER INTO A WALL OUTLET AND THEN CONNECT THE OTHER END WITH THE CHARGING PORT. • CHARGE THE BATTERY 15 TO 18 HOURS BEFORE INITIAL USE. -
Page 55: Helmet Safety
Helmet Safety PROPER POSITIONING: IMPROPER POSITIONING: THE FOREHEAD IS COVERED THE FOREHEAD IS EXPOSED. BY THE HELMET. A FALL COULD RESULT IN SERIOUS INJURY. * WEAR A HELMET, APPROPRIATE CLOTHING, SHOES, AND SAFETY GEAR. AVOID CLOTHING THAT CAN GET CAUGHT INTO OR UNDER THE WHEELS. -
Page 56: Care & Maintenance
CLEANING THE SAFARA MAX TO CLEAN THE SAFARA MAX, CAREFULLY WIPE WITH A DAMP CLOTH, THEN DRY WITH A DRY CLOTH. DO NOT APPLY WATER DIRECTLY TO THE SAFARA MAX; WATER CAN CAUSE DAMAGE TO THE FRAME, SEAT, AND ELECTRICAL COMPONENTS. - Page 58 Stay connected. Be sure to follow @ridejetson on social media to learn about fantastic offers, giveaways, and all the latest Jetson news. Loving your ride? Then be sure to leave a review at ridejetson.com/reviews. We can’t wait to hear from you!
- Page 60 US/CANADA: 1-888-976-9904 MEX: +001 888 976 9904 UK: +44 (0)33 0838 2551 Manufactured in Zhejiang, China Imported by Jetson Electric Bikes LLC. P.O. Box 320149, 775 4th Ave #2, Brooklyn, NY 11232 www.ridejetson.com Made in China...