Vizio VMA13-32 Installation Instructions Manual
Vizio VMA13-32 Installation Instructions Manual

Vizio VMA13-32 Installation Instructions Manual

Articulating swingout arm; tilt/pivot mount for use with vizio lcd tvs from 13”-32”

Advertisement

Quick Links

Installation Instructions
VMA13-32
VMT13-32
Articulating Swingout Arm
Tilt/Pivot Mount
For use with Vizio LCD TVs from 13"-32"
Vizio
320 A Kalmus Dr.
Costa Mesa, CA 92626
Phone: (714) 668-0588
Fax: (714) 668-9099
www.vizioce.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VMA13-32 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vizio VMA13-32

  • Page 1 Installation Instructions VMA13-32 VMT13-32 Articulating Swingout Arm Tilt/Pivot Mount For use with Vizio LCD TVs from 13”-32” Vizio 320 A Kalmus Dr. Costa Mesa, CA 92626 Phone: (714) 668-0588 Fax: (714) 668-9099 www.vizioce.com...
  • Page 2: Table Of Contents

    VMA13-32 / VMT13-32 Warning Statements Parts List Installation Tools Backplate Installation- Wood stud Backplate Installation - Concrete Surface Mount Installation Installing the Monitor Adjusting the Swingout Arm Adjusting the Tilt/Pivot Mount Technical Specifications Warranty Contact Vizio Page 2 TABLE OF CONTENTS...
  • Page 3: Warning Statements

    Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available). Contact VIZIO with any technical/ installation questions. Installation Instructions Warning Statements...
  • Page 4: Parts List

    This mount is shipped with all installation hardware and components. Make sure that none of these parts are missing and/ or damaged before beginning installation. If there are parts missing and/or damaged, please stop and contact Vizio (714) 668-0588. Swingout Arm (1ea) 1/4”...
  • Page 5: Backplate Installation- Wood Stud

    Backplate Installation - Wood Stud NOTE: These installation instructions will apply to the VMA13-32 / VMT13-32 Swingout Arm and the Tilt/Pivot Mount. The following steps will outline how the back plate will be mounted. Determine where the mount location will be.
  • Page 6: Backplate Installation - Concrete Surface

    VMA13-32 / VMT13-32 Backplate Installation - Concrete Surface NOTE: These installation instructions will apply to the VMA13-32 / VMT13-32 Swingout Arm and the Tilt/Pivot Mount. The following steps will outline how the back plate will be mounted. Determine where the mount location will be.
  • Page 7: Mount Installation

    Failure to fully tighten the locking screw may result in possible damage to your display. NOTE: In reference to Figure 5, the dash lines represent the back plate that is mounted to an existing surface. Installation Instructions Figure 5. Mount Installation VMA13-32 / VMT13-32 Page 7...
  • Page 8: Installing The Monitor

    VMA13-32 / VMT13-32 Display Installing the Monitor Loosely tighten two (2) Phillips Head screws to the top of the mounting points. Insert the head of the screws through the keyhole slots and then secure the bottom two (2) M4 x 10mm (or 16mm) Phillips Head screws to secure the flat panel to the mounts, then tighten the upper M4 screws.
  • Page 9: Adjusting The Swingout Arm

    Bottom Adjustment nuts NOTE: The tilt/pivot adjustment nut is located on the back of the tilt/pivot mount. Installation Instructions NOTE: The mount shown in this illustration is upside down to access the caps adjustment nuts. VMA13-32 / VMT13-32 Page 9...
  • Page 10: Adjusting The Tilt/Pivot Mount

    VMA13-32 / VMT13-32 Adjusting the Tilt/Pivot mount The tilt and pivot tensions are pre-set at the factory. To alter these settings, perform the following steps. Use a M3 Allen Wrench and loosen the locking screw via the access hole (Figure 10).
  • Page 11: Technical Specifications

    VMA13-32 / VMT13-32 Technical Specifications Figure 11. VMA13-32 / VMT13-32 Swingout Arm Figure 12. VMA13-32 / VMT13-32 Tilt/Pivot Mount Installation Instructions Page 11...
  • Page 12: Warranty

    VMA13-32 / VMT13-32 Warranty These products carry a limited 1 year warranty from purchase date against defects in materials and workmanship. Vizio is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. Contact Vizio In the event of missing and/or damage equipment, or technical questions, the following information can help in the completion of the installation.

This manual is also suitable for:

Vmt13-32

Table of Contents