Dvd home theater sound system model no.sc-ht330 (32 pages)
Summary of Contents for Panasonic SA-HT920P
Page 1
ORDER NO.MD0403065C1 DVD Home Theater Sound System SA-HT920P SA-HT920PC Color (S).......Silver Type Specifications • General Power Source: AC 120V, 60Hz 26 W Power consumption: 430 × 68 × 432 mm Dimensions (W × H × D): (16-15 / 16 ” × 2-11 / 16 ” × 17 ” ) Mass: 4.1 kg (9.0Ibs)
Page 2
(100kHz in step) 2.5 µ V (IHF) Sensitivity: 2.2 µ V S / N 26dB 75 Ω (non balance) Antenna Terminal: • AM / MW tuner section 520-1710kHz (10kHz in step) Frequency Range: AM Sensitivity S / N 20dB at 1000kHz: 560 µ...
Page 4
1 Use of Active Subwoofer 1.1 Checking Player when Active Subwoofer is not used This unit uses the active subwoofer to supply the power of the component, and the active subwoofer should be connected to the component to check operational conditions of the component. If the active subwoofer is not available due to repair of the unit, use the following equipment.
Page 5
2 Safety Precautions 2.1 GENERAL GUIDELINES When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Page 6
3 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field- effect transistorsand semiconductor "chip"...
Page 7
4 Before Repair and Adjustment (Using Active Subwoofer) Disconnect AC power, discharge Power Supply Capacitors C546~C549 through a 10 Ω, 10 W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Page 8
5 Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: No sound is heard when the power is turned on. Sound stops during a performance. The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
Page 9
6 Precaution of Laser Diode CAUTION: This unit utilizes a laser. Invisible laser radiation is emitted from the optical pickup lens when the unit is turned on. Wavelength: 662nm(DVD)/785nm(VCD/CD). Maximum output radiation power from pickup: 100µW/VDE Do not look directly into the pick up lens. Do not use optical instruments to look at the pick up lens.
Page 10
7 About Lead Free Solder (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a Pbf stamp on the PCB. Caution: Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher.
Page 12
9 Accessories Remote control AM loop antenna FM indoor antenna Video cable Large screws 5 Speaker cables (×5) AC power supply cord Antenna plug System cable Small screws...
Page 13
10 Handling Precautions for Optical Pickup Unit The laser diode in the optical pickup unit may brake down due to static electricity of clothes or human body. Use due caution to electrostatic breakdown when servicing and handling the laser diode. 10.1 Cautions to Be Taken in Handling the Optical Pickup Unit The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or...
Page 14
works is completed. 10.3.1 Worktable grounding Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet. 10.3.2 Human body grounding Use the anti-static wrist strap to discharge the static electricity form your body.
Page 15
11 Disassembly and Main Component Replacement Procedures “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. For assembly after operation checks or replacement, reverse the respective procedures.
Page 16
Step 3 Pull out the FFC from connectors (CN6801 & CN6901). Checking of Headphone P.C.B. and FL P.C.B. 11.3 Disassembling the Tray Assembly Follow the (Step 1) - (Step 2) of Item 11.1. Follow the (Step 1) - (Step 4) of Item 11.2. Step 1 Keep the close lock gear pressed in clockwise, move the tray assembly in the direction of the arrow.
Page 17
Step 2 Hold close lock gear, push and release the 4 claws in the direction of arrow, and then remove the tray assembly. Step 3 Pull out FFC CN6002. Step 4 Remove 4 screws. Checking of Main P.C.B., Tray Motor and Sensor P.C.B. Checking of Loading Motor P.C.B.
Page 18
11.4 Removal of the Tray Base Guide (L) and Tray Base Guide (R) Follow the (Step 1) - (Step 2) of Item 11.1. Follow the (Step 1) - (Step 4) of Item 11.2. Follow the (Step 1) - (Step 5) of Item 11.3. Step 1 Remove the 2 screws.
Page 19
Follow the (Step 1) - (Step 4) of Item 11.2. Follow the (Step 1) - (Step 5) of Item 11.3. Follow the (Step 1) - (Step 2) of Item 11.5. Step 1 Rotate open lock gear in the direction of arrow. (Anti-clockwise) Step 2 Release claw of open lock gear, remove open lock gear in the direction of arrow.
Page 20
Follow the (Step 1) - (Step 4) of Item 11.2. Follow the (Step 1) - (Step 5) of Item 11.3. Step 1 Remove 2 screws. Step 2 Release 4 claws at Tray Motor P.C.B. and Sensor P.C.B. 11.9 Removal of the CD Traverse Unit Follow the (Step 1) - (Step 2) of Item 11.1.
Page 21
Step 2 Flip the base mecha. Step 3 Release the 2 claws in the direction of arrow (1), and then push the pulley pin in the direction of arrow (2). 11.11 Removal of the Loading Motor P.C.B. Follow the (Step 1) - (Step 2) of Item 11.1. Follow the (Step 1) - (Step 4) of Item 11.2.
Page 22
Step 1 Release the claw in the direction of arrow (1), and then push drive gear shaft up. Step 2 Remove Drive Gear (A) and Drive Gear (B). 11.13 Disassembling the Fixed Plate, Magnet and Clamper Follow the (Step 1) - (Step 2) of Item 11.1 Follow the (Step 1) - (Step 4) of Item 11.2.
Page 23
Step 2 Remove 1 screw and support piece. 11.15 Removal of the Slide Plate (L) & (R) and Change Lever Follow the (Step 1) - (Step 5) of Item 11.3. Step 1 Press the claw and push the Slide Plate (L) up. Step 2 Remove slide plate (L) &...
Page 24
Step 1 Rotate cam gear anti-clockwise. Align at position (C) as marking on gear with arrow. Step 2 Make sure drive gear (A) at vertical position. Step 3 Push tray base to the direction of arrow shown.
Page 25
12 DVD-Optical Pick-up Self- Diagnosis and Replacement Procedure 12.1 Optical Pickup Breakdown Diagnosis The optical pickup self-diagnosis function and tilt adjustment check function have been included in this unit. When repairing, use the following procedure for effective Self-diagnosis and tilt adjustment. Be space sure to use the self- diagnosisfunction before replacing the optical pickup when "NO DISC"...
Page 26
Player Remote control Application Note buttons unit buttons (Refer to the item, “12.3. Error code display Self Diagnostic Function-Error Code ”). Refer to the item “15.4. Optical Tilt adjustment adjustment”). Area number and broadcasting system check Built-in program version check STOP DISPLAY DVD laser drive current check...
Page 27
Disc code Big possibility of disc specification violation during highlight F103 Illegal highlight Position display HIC Error F4FF Force initialize failure (time out) Micro computer error F700 MBX overflow When replying message to disc manager F701 Message command does not end Next message is sent before replying to disc manager Message is changed before it is sent as a reply to disc F702...
Page 29
12.6 Sales demonstration lock function This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function. "LOCKED" is displayed on the unit, and ordinary operation is disabled. 12.6.1 Setting Prohibiting removal of disc Select the DVD/CD function.
Page 30
Player , SELECTOR, , VOLUME KNOB, DISC CHECK, DISC CHANGE, DISC1-DISC5 SLEEP, REPEAT, 0~9, RETURN, TOP MENU, , POSITION Remote MEMORY, TUNER/BAND, D.MIX, CH SELECT/ TEST, SET UP/ MUTING, DISPLAY, GROUP, TV, controller unit VCR/ AUX, QUICK REPLAY, SUBTITLE, FL DISPLAY, CH & VOLUME 12.6.2 Cancellation The lock can be cancelled by the same procedure as used in setting.
Page 31
13 Self-Diagnosis Function 13.1 Automatic Displayed Error Codes 13.1.1 Automatic Display Function For a power unit error, the code is automatically displayed. F61: Automatically displayed on the LCD of the player. 13.1.2 Re-Display For F61 Display ¡ When the code, F61 is displayed, the power is automatically turned off. ¡...
Page 32
13.2.2 Re-Display Press the power button to turn off the power, and then turn on the power. The details of self diagnosis are stored in the unit memory. To retrieve them, follow the procedure described the above, “Activating Self-Diagnosis Function and Displaying Method”.
Page 33
14 Service Precautions 14.1 Recovery after the DVD player is repaired When FROM or module P.C.B. is replaced, carry out the recovery processing to optimize the drive. Playback the recovery disk to process the recovery automatically. Recovery disc (Product number: RFKZD03R005) Performing recovery Load the recovery disc RFKZD03R005 on to the player and run it.
Page 34
15 Adjustment Procedure 15.1 Service Tools and Equipment Application Name Number DVD test disc DVDT-S15 or DVDT-S01 Tilt adjustment TORX screw driver (T6) Available on sales route. (T6) or RFKZ0185 Others Grease RFKXPG641 CD test disc PVCD-K06 or any other commercially available disc Confirmation VCD test disc PVCD-K06 or any other commercially available disc...
Page 35
15.4.1.1 Adjustment procedure While pressing STOP button on the main unit, press "5" on the remote control unit. Confirm that "J_xxx/yyy_zz" (display1/display2) is shown on the front display. For your information: "yyy" and "zz" shown to the right have nothing to do with the jitter value. "yyy" is the error counter, while "zz" is the focus drive value.
Page 36
After fixing, reassemble traverse unit, clamper base, tray and top cover.
Page 37
16 Abbreviations INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMPOUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT...
Page 38
DSLF DATA SLICE LOOP FILTER DIGITAL VIDEO DISC INITIAL/LOGO ABBREVIATIONS ERROR TORQUE CONTROL ERROR TORQUE CONTROL REFERENCE ENCSEL ENCODER SELECT ETMCLK EXTERNAL M CLOCK (81MHz/40.5MHz) ETSCLK EXTERNAL S CLOCK (54MHz) FBAL FOCUS BALANCE FCLK FRAME CLOCK FOCUS ERROR FOCUS ERROR AMP INVERTED INPUT FOCUS ERROR AMP OUTPUT FREQUENCY GENERATOR FREQUENCY SUB CARRIER...
Page 39
SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK SERIAL CLOCK SERIAL DATA SEG0~UP FL SEGMENT OUTPUT SELCLK SELECTCLOCK SERIAL PORT ENABLE SIN1, 2 SERIAL DATA IN SOUT1, 2 SERIAL DATA OUT SPDI SERIAL PORT DATA INPUT SPDO...
Page 40
XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPTREQUEST TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE TAL OSCILLATOR OUTPUT X READ ENABLE XSRMCE X SRAM CHIP ENABLE XSRMOE...
Page 41
17 Voltage Chart 17.1 DVD Module P.C.B. 17.2 Main P.C.B. 17.3 FL P.C.B. 17.4 Loading Motor P.C.B. 17.5 Tray Motor P.C.B. 17.6 Sensor P.C.B.
Page 42
18 Schematic Diagram Notes This schematic diagram may be modified at any time with the development of new technology. Notes: S6801: Play and memory switch ( Memory). S6802: R. skip, search and tuning switch ( / TUNING S6803: F. skip, search and tuning switch ( / TUNING S6804: Stop and FM mode switch (...
Page 43
: FM/AM signal line : -B Signal line Caution! IC and LSI are sensitive to static electricity. Secondary trouble can be prevented by taking care during repair. Cover the parts boxes made of plastics with aluminum foil. Ground the soldering iron. Put a conductive mat on the work table.
Page 48
23 Illustration of IC ’ s, Transistors and Diodes...
Page 49
24 Terminal Function of ICs 24.1 IC2018 (C2CBJG000474): Operation CPU Pin No. Terminal Name Function LOAD I UP/DOWN switch signal input OP/CL REV O Reverse control signal output for OPEN/CLOSE motor OP/CL FWD O Forward control signal output for OPEN/CLOSE motor OPEN SW I Rotary tray OPEN switch signal input POSSITION...
Page 50
VOL CK O Clock output for 6ch VOL ASP - Not used, open DSP CS O Chip select signal output for DSP2 DSP RST O Reset signal output for DSP2 DSP LAT O Latch signal output for DSP2) DSP CLK O Clock output for DSP2 DSP ACK I Acknowledge signal input from DSP2...
Page 51
25 Parts Location and Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufacture’s specified parts shown in the parts list. *Warning: This product uses a laser diode.
Page 52
RHD30090 SCREW RHD30107 SCREW RKA0145-K CUSHION RKA0157-S FOOT ASSY RKM0498A-S TOP CABINET RMA1769 PANEL ANGLE RMR1558-W RING (VOLUME KNOB) RMK0593A BOTTOM CHASSIS RGKX0254-K TRAY LID RMN0730 TRAY GUIDE L RMN0731 TRAY GUIDE R RMNX0120 FL HOLDER RMVX0080 WIRE HOLDER XTB3+10JFZ SCREW XTB3+6J SCREW...
Page 53
RMS0802-J DRIVE GEAR SHAFT XTN26+14JFZ SCREW XTV2+6G PCB SCREW XWG6FFY WASHER RMF0182 TRAY FELT RMS0123-1 FIXED PIN B RMM0256 BLOCK BASE RMX0274 TRAY SUPPORT R RMX0275 TRAY SUPPORT L RMX0290 PLASTIC SHEET 25.2 Component Parts List Ref. No. Part No. Part Name &...
Page 78
27 Additional Contents 27.1 Notes This document describes necessary service information for the mentioned models on the change of IC2002 & the modification of circuit. This IC is a DC-DC converter for power supply voltage. Following sections include information on the IC type &...
Page 79
The electrical part list change between the original & revise. 27.2 Printed Circuit Board Diagram (Revise) 27.2.1 Main P.C.B (SA-HT920P/PC) With reference to page 56 (section 21) for original service manual as mentioned models. The below Main P.C.B. applies to RJBX0388A-5 & RJBX0388B & above only. The P.C.B. part no. (complete P.C.B.
Page 80
27.4 Block Diagram (Revise) 27.4.1 Block Diagram (SA-HT920P/PC) Block Diagram Page 43 27.5 Part List (Revise) This section illustrates the changes in the electrical parts list between the original & the revised. 27.5.1 Part List (SA-HT920P/PC) Part Number Model No.
Page 85
IC2000 Ref No. MODE CD PLAY STANDBY IC2001 Ref No. MODE CD PLAY 13.4 STANDBY 13.5 IC2002 Ref No. MODE CD PLAY 13.5 STANDBY 13.7 IC2004 Ref No. MODE CD PLAY STANDBY IC2005 Ref No. MODE CD PLAY STANDBY IC2006 Ref No.
Page 86
IC2021 Ref No. MODE CD PLAY -6.7 STANDBY -6.7 IC2022 Ref No. MODE CD PLAY -6.7 STANDBY -6.7 Q2000 Q2001 Q2002 Q2004 Q2011 Ref No. MODE CD PLAY 13.5 -3.0 13.5 STANDBY 13.8 -3.0 13.7 Q2012 Q2013 Q2014 Q2015 Q2016 Ref No.
Page 87
IC8001 Ref No. MODE CD PLAY STANDBY IC8001 Ref No. MODE CD PLAY STANDBY IC8001 Ref No. MODE CD PLAY STANDBY IC8001 Ref No. MODE CD PLAY STANDBY IC8001 Ref No. MODE CD PLAY STANDBY IC8001 Ref No. MODE CD PLAY STANDBY -0.1 IC8001...
Page 88
IC8451 Ref No. MODE CD PLAY STANDBY IC8451 Ref No. MODE CD PLAY STANDBY IC8601 Ref No. MODE CD PLAY STANDBY IC8605 Ref No. MODE CD PLAY STANDBY IC8611 Ref No. MODE CD PLAY STANDBY IC8651 Ref No. MODE CD PLAY STANDBY IC8651 Ref No.
Page 90
Q9101 Q9102 Ref No. MODE CD PLAY STANDBY...
Page 91
20 Schematic Diagram SCHEMATIC DIAGRAM-1 DVD MODULE(IN/OUT) CIRCUIT : +B SIGNAL LINE : CD-DA SIGNAL LINE : MAIN SIGNAL LINE : DVD(VIDEO) SIGNAL IC8271 Spindle Motor Drive SPINDLE MOTOR ASSY IC8251 Tracking Coil/Focus Coil Traverse Motor Drive QR8571 Switch Q8550 Switch Q8560 Switch...
Page 92
DVD(VIDEO) SIGNAL LINE : DVD(AUDIO) SIGNAL LINE IC8451 MAIN CIRCUIT (CN2004)ON SCHEMATIC DIAGRAM-3 IC8111 Power Supply IC QR8420 Muting Switch IC8691 AND GATE LOGIC IC IC8695 AND GATE LOGIC IC TC8004 TC8010 K8004 K8009...
Page 93
SCHEMATIC DIAGRAM-2 DVD MODULE(DV2) CIRCUIT : +B SIGNAL LINE : CD-DA SIGNAL LINE : DVD(VIDEO) SIGNAL LINE : DVD(AUDIO) S IC8051 64M SDRAM IC8651 RFKFMH81T160 IC8611 C3EBGZ000001 EEPROM IC IC8001 DV2-1 LSI IC8601 IC8605 Voltage Detecting IC RESET IC...
Page 94
: DVD(AUDIO) SIGNAL LINE FLASH ROM WRITING...
Page 95
SCHEMATIC DIAGRAM-3 : +B SIGNAL LINE : MAIN SIGNAL LINE : DVD(VIDEO) SIGNAL LINE : FM/AM SIGNAL LINE MAIN CIRCUIT CN2003 SEL FL INPUT L SEL FR INPUT AGND C2104 C2204 INPUT R 470P 470P -7.5V -7.5V DSP A+5V DEC A+5V DSP D+5V DEC D+5V DGND...
Page 96
M/AM SIGNAL LINE IC2007 C0GAG0000007 Motor Drive(Tray) SEL FL SEL FR -7.5V DSP A+5V CN2010 TRV REV DSP D+5V TRV FWD TRV- 11 C+9V TRV+ C2023 C2024 L2003 R2093 R2094 DGND D2005 D2004 16V47 R2097 R2098 J0JBC0000015 B0ECKM000016 B0ECKM000016 4.7K PHT DRV SENSOR L2004...
Page 97
SCHEMATIC DIAGRAM-4 MAIN CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : MAIN SIGNAL LINE : FM/AM SIGNAL LINE C2819 16V47 R2163 R2263 C2818 16V47 C2810 220P C2163 C2263 C2809 220P R2265 R2165 C2811 0.01 4.7K 4.7K C2812 0.01 R2162 7.5K C2161 0.1 C2162 0.033...
Page 99
SCHEMATIC DIAGRAM-5 MAIN CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : DVD(VIDEO) SIGNAL LINE C2177 16V47 R2620 R2308 R2179 R2166 R2266 R2897 1.8K 1.8K 1.8K 1.8K STBY LED Q2029 Q2600 Q2103 Q2105 Q2201 Q2602 B1GBCFJN0021 B1GDCFGA0014 B1GDCFGA0014 B1GDCFGA0014 B1GDCFGA0014 B1GDCFJJ0023 Muting Control...
Page 100
R2058 R2056 R2057 C2000 R2080 R2059 220 MRSLED R2037 1K VOL CK DISC5 LED VOL CK R2036 1K VOL DA DISC4 LED VOL DATA MUTE L DISC3 LED MUTE L R2035 220 YC H DISC2 LED YC H R2034 220 V MUTE3 DISC1 LED (RGB H)VMUTE3...
Page 101
SCHEMATIC DIAGRAM-6 MAIN CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : MAIN SIGNAL LINE IC2004 IC2000 IC2002 IC2001 C0CBADG00023 C0CBADG00023 C0DBAZG00033 C0DBAZG00033 Regulator Regulator DC-DC Converter DC-DC Converter C2053 L2019 G0A101G00022 R2898 R2860 4.7K L2011 C2060 10V1 DVD D+5V G0A100G00005 R2899 R2900...
Page 102
R2974 DISC2 R2975 DISC1 CN2008 KEY2 CN2009 KEY2 CSMLED JOG B (SPE A) JOG B DIGITAL JOG A (SPE B) JOG A C+9V BLUE LED C+9V BLUE LED VRSLED VREF+ (SPE C) VREF+ HEADPHONE MRSLED (SPE IN) CIRCUIT GND1 DISC5 (CN6801)ON DISC5 SCHEMATIC...
Page 103
CHEMATIC DIAGRAM - 7 : MAIN SIGNAL LINE : +B SIGNAL LINE : -B SIGNAL LINE DSP CIRCUIT L603 C647 C648 C678 6.3V100 L604 R679 R680 L600-L601 IC604 L603-L604 J0JBC0000019 IC604 Q605 J0JBC0000019 Q606 C0CBCBE00003 L600 POWER SUPPLY R678 C602 C649 0.01 C650...
Page 111
SCHEMATIC DIAGRAM-1 DVD MODULE(IN/OUT) CIRCUIT : +B SIGNAL LINE : CD-DA SIGNAL LINE : MAIN SIGNAL LINE : DVD(VIDEO) SIGNAL LINE : DVD(AUDIO) SIGNAL LINE IC8271 Spindle Motor Drive SPINDLE MOTOR ASSY IC8251 Tracking Coil/Focus Coil Traverse Motor Drive IC8451 MAIN CIRCUIT (CN2004)ON...
Page 112
VOLUME OPTICAL PICKUP CN6901 VR6800 FL P.C.B. JK6801 HEADPHONE P.C.B. CN6801 HEADPHONE FP8501 JACK DVD MODULE P.C.B. (SIDE:A) CN2009 CN2008 M9101 SENSOR P.C.B. TRAY MOTOR CN9102 P.C.B. CN2010 MAIN P.C.B. SSPINDLE MOTOR ASS'Y CN2004 FP8271 P.C.B. LOADING MOTOR P.C.B. JK600 M9001 TUNER PACK UNIT DVD MODULE P.C.B.
Page 113
SCHEMATIC DIAGRAM-2 DVD MODULE(DV2) CIRCUIT : +B SIGNAL LINE : CD-DA SIGNAL LINE : DVD(VIDEO) SIGNAL LINE : DVD(AUDIO) SIGNAL LINE IC8051 64M SDRAM FLASH ROM WRITING IC8651 RFKFMH81T160 IC8611 C3EBGZ000001 EEPROM IC IC8001 DV2-1 LSI IC8601 IC8605 RESET IC Voltage Detecting IC...
Page 114
SCHEMATIC DIAGRAM-3 : +B SIGNAL LINE : MAIN SIGNAL LINE : DVD(VIDEO) SIGNAL LINE : FM/AM SIGNAL LINE MAIN CIRCUIT IC2007 C0GAG0000007 Motor Drive(Tray) CN2003 SEL FL INPUT L SEL FR INPUT AGND C2104 C2204 470P 470P INPUT R -7.5V -7.5V DSP A+5V DEC A+5V...
Page 115
SCHEMATIC DIAGRAM-4 MAIN CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : MAIN SIGNAL LINE : FM/AM SIGNAL LINE C2819 16V47 R2163 R2263 R2505 C2503 C2506 C2818 16V47 0.033 0.01 C2810 220P R2508 C2163 C2263 C2504 R2504 C2505 1.8K C2809 220P 0.068 R2619...
Page 116
SCHEMATIC DIAGRAM-5 MAIN CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : DVD(VIDEO) SIGNAL LINE C2177 R2058 16V47 R2056 R2057 R2620 R2308 R2179 R2166 R2266 R2897 1.8K 1.8K 1.8K 1.8K C2000 STBY LED Q2029 Q2600 Q2103 Q2105 Q2201 Q2602 B1GDCFGA0014 B1GDCFGA0014 B1GDCFGA0014...
Page 117
SCHEMATIC DIAGRAM-6 MAIN CIRCUIT : +B SIGNAL LINE : -B SIGNAL LINE : MAIN SIGNAL LINE IC2004 IC2000 IC2002 IC2001 C0CBADG00023 C0CBADG00023 C0DBAZG00033 C0DBAZG00033 R2974 Regulator Regulator DC-DC Converter DC-DC Converter DISC2 R2975 DISC1 C2053 L2019 G0A101G00022 CN2008 R2898 R2860 KEY2 CN2009 4.7K...
Page 118
CHEMATIC DIAGRAM - 7 : +B SIGNAL LINE : -B SIGNAL LINE : MAIN SIGNAL LINE DSP CIRCUIT L603 C647 C648 C678 6.3V100 L604 R680 R679 L600-L601 IC604 L603-L604 J0JBC0000019 IC604 Q605 J0JBC0000019 Q606 C0CBCBE00003 L600 POWER SUPPLY R678 C602 0.01 C649 C650...
Page 119
SCHEMATIC DIAGRAM-8 FL CIRCUIT : +B SIGNAL LINE : MAIN SIGNAL LINE HEADPHONE CIRCUIT FL6901 A2BD00000082 CN6901 JK6901 R6940 1 K2HC103A0023 L6101 R6939 1 J0JBC0000019 FLDA C6903 C6905 R6935 R6936 C6101 L6201 50V22 50V22 0.047 FLCLK J0JBC0000019 HEADPHONE FLCS JACK C6201 D6911 D6910...
Page 121
IC8001 IC8251 MN2DS003APH C0GBG0000044 OPTICAL PICK UP UNIT TRACKING COIL/FOCUS COIL/TRAVERSE MOTOR DRIVE PHOTO DETECTOR VIN1 VOL4+ VIN2 VIN3 HEAD VIN4 VOL4- LEVEL SHIFT VIN8 BIAS1 VIN7 VIN6 TRV DRV VIN1 VIN5 PWM1 VOL3+ VIN10 F0 DRV VIN2 TRAVERSE VIN9 PWM0 MOTOR LASER DIODE...
Page 122
IC8051 IC8001 IC8451 C3ABPG000068 MN2DS003APH C0FBBK000036 64M SDRAM AUDIO DAC V OUT7 DVD MIX L OUTPUT AMP AND LOW-PASS FILTER BCK IN SRCK LRC IN MEMORY MEMORY LRCK ADDRESS ADDRESS D IN1 V OUT8 DVD MIX R OUTPUT AMP AND AD OUT0 SERIAL 12bit...
Page 123
TUNER PACK AM ANT FM ANT IC2006 C9ZB00000431 MIXER IF AMP VIDEO DRIVE COIL COIL RF AMP BUFFER BIAS 150K Y/PY/G CY IN 13.5MHz CY OUT JK2001 Y(RED) (FM) BIAS CY SAG 150K CB/PB/B CB IN 13.5MHz CB OUT JK2001 CB(GREEN) TUN L BIAS...
Page 124
IC2013 C0AABB000125 HEADPHONES AMP IC2011 C1BB00000845 (6)2 1(7) APS(INPUT SELECT/DIGITAL SOUND PROCESSOR/ELECTRONIC VOLUME/TONE) (5)3 Q2102 Q2201 TMF L TMF RB TMF LB (TMFR) (TMF RA) (TMF LA) MUTING MUTING CONTROL (L OUT2) L OUT1 JK2001 (60)59 (OUT FR) TONE LINE OUT OUT FL 39(36) (IN A2)
Page 125
SIGNAL LINES : MAIN SIGNAL LINE : AM SIGNAL LINE : DVD AUDIO SIGNAL LINE : FM SIGNAL LINE : AM OSC SIGNAL LINE : DVD VIDEO SIGNAL LINE : FM OSC SIGNAL LINE : FM /AM SIGNAL LINE : CD-DA (AUDIO /VIDEO) SIGNAL LINE ( ) Indicates the Pin No.
Page 126
A A A A A A A A DVD MODULE P.C.B. (REP3654G) (SIDE:A) DVD MODULE P.C.B. (REP3654G) (SIDE:B) CP8252 TP8514 C8254 C8255 C8503 LB8502 CP8251 TP8515 TP8517 TP8500 TC8502 TC8501 R8501 TP8511 TP8520 TP8521 LB8501 TP8516 C8505 RA8502 TP8510 TP8502 TP8524 TP8519 TP8501...
Page 127
A A A A MAIN P.C.B. (REPX0420A) R2884 R2891 C2042 R2885 C2803 C2804 C2802 C2801 C2044 L2022 R2878 R2886 R2879 C2808 R2883 L2025 R2882 R2889 R2880 C2040 C2805 R2881 R2887 C2807 C2608 R2888 IC2007 L2003 L2004 W2327 R2127 C2206 C2106 IC2006 R2802 W2210...
Model No.SA-HT920PPC, Order No. MD0403065C1 CONTENTS Page Page 1 Notes 3.1. Schematic Diagram (SA-HT920P/PC) 1.1. Change of IC type (IC2002) 4 Block Diagram (Revise) 1.2. Method to identity before repair 4.1. Block Diagram (SA-HT920P/PC) 2 Printed Circuit Board Diagram (Revise) 5 Part List (Revise) 2.1.
SA-HT920P / SA-HT920PC 1 Notes This document describes necessary service information for the mentioned models on the change of IC2002 & the modification of circuit. This IC is a DC-DC converter for power supply voltage. Following sections include information on the IC type &...
SA-HT920P / SA-HT920PC 1.2. Method to identity before repair This section describes the method to ensure proper service parts replacement to be carried out accordingly. 1.2.1. To check Main P.C.B. version · Below is the procedures to determine the version for Main P.C.B..
SA-HT920P / SA-HT920PC 2 Printed Circuit Board Diagram (Revise) 2.1. Main P.C.B (SA-HT920P/PC) · With reference to page 56 (section 21) for original service manual as mentioned models. · The below Main P.C.B. applies to RJBX0388A-5 & RJBX0388B & above only. The P.C.B. part no. (complete P.C.B. with parts) remains unchanged.
Page 138
SA-HT920P / SA-HT920PC A A A A MAIN P.C.B. (REPX0420A) R2884 R2891 C2042 R2885 C2803 C2804 C2802 C2801 C2044 L2022 R2878 R2886 R2879 C2808 R2883 L2025 R2882 R2889 R2880 C2040 C2805 R2881 R2887 C2807 C2608 R2888 IC2007 L2003 L2004 W2327...
SA-HT920P / SA-HT920PC 3 Schematic Diagram (Revise) 3.1. Schematic Diagram (SA-HT920P/PC) · With reference to the schematic diagram of original service manual. This section illustrate the comparison between the original (for RJBX0388A-4 & below) & new (for RJBX0388A-5 or RJBX0388B & above).
SA-HT920P / SA-HT920PC 5.1. Part List (SA-HT920P/PC) Part Number Model No. Ref. No. Original Part No. New Part No. Part Name & Description Notes Remarks SA-HT920P/PC D2807 B0ACCK000005 DIODE [M] ADD Q2805 B1ABCF000131 TRANSISTOR [M] ADD C2092 ECJ1VB1C103K 16V 0.01...
Page 146
SA-HT720P / SA-HT720PC / SA-HT720GCP / SA-HT920P / SA-HT920PC Part Number Model No. Ref. No. Original Part No. New Part No. Notes Part Name & Descriptions SA-HT920P/PC-S IC869 C0JBCA000066 C0JBAA000346 7,C AND GATE LOGIC IC [M] (CHANGE) SA-HT920P/PC-S IC869 C0JBCA000066 C0JBAA000346 7,C AND GATE LOGIC IC [M] (CHANGE) [M] indicates parts that are supplied by PAVCSG.