Table of Contents
Advertisement
Connection
DMX Address-In this menu, you can select the DMX Address.
1. Press "ENTER" button and then UP or DOWN button until "DMX Address " is showed.
2. Press "ENTER" button, and "DMX Address" will be showed. Then press ENTER.
1) "xxx" will be showed, "xxx" represents the showed address. You can press the UP or DOWN button
to select your desired address.
Channels Mode-In this menu, you can connect several pieces of lights with DMX cable and control
them with control console.
Master / Slave connection
1. Press "ENTER" button and then UP or DOWN button until "Channels Mode " is showed.
2. Press "ENTER" button, and "Channels Mode" will be showed. Then press ENTER.
1) "Channel [xx]" will be showed, "X" represents the showed DMX channel mode. You can press the
UP or DOWN button to select your desired Channel mode.
DMX State-In this menu, you can learn about the information of DMX Hold and Blackout.
1. Press "ENTER" button and then UP or DOWN button until "DMX State" is showed.
2. Press "ENTER" button, and "DMX Hold" or "Blackout" will be showed. Then press
ENTER, and you can select your desired mode.
Wireless connection
Manual Mode-In this menu, you can adjust the value of static color and strobe speed as you like.
POWER
1. Press "ENTER" button and then UP or DOWN button until "Manual Mode" is showed.
2. Press "ENTER" button, and there are six options. Then press ENTER to select the option and
press UP or DOWN button to select the value you desire as below:
1) RED - You can adjust the red brightness in this menu.
2) GREEN - You can adjust the green brightness in this menu.
3) BLUE - You can adjust the blue brightness in this menu.
4) WHITE - You can adjust the white brightness in this menu.
5) COLOR -You can select 255 static color in this menu.
Connection
6) STROB - You can adjust the strobe speed in this menu.
Press "ENTER" and then press "UP" or "DOWN" to "SET UP" .
AUTO mode-In this menu, you can select your desire AUTO mode and adjust the running speed.
Press "ENTER" and then press "UP" or "DOWN" to "Wireless rel" is displayed, press
1. Press "ENTER" button and then UP or DOWN button until "AUTO mode" is showed.
"ENTER".Then press "DMX Mode" is ok.
2. Press "ENTER" button, and "SPEED" or "AUTO MODE" will be showed. Then press ENTER, and
Then, until Green wireless signal is showed. Then Wireless DMX connected
you can see two items as below:
1) SPEED - You can select your desired speed in this menu.
success.
2) AUTO MODE - You can select your desired auto mode in this menu.
About the condition of wireless signal, green means the setting is successful,red
means the signal is unsuccessful.
Slave Mode-In this menu, you can select SLAVE mode. In SLAVE mode, you can select one light as
the MASTER light and other lights in SLAVE mode will run following the MASTER light.
Release wireless DMX signal
1. Press "ENTER" button and then UP or DOWN button until "Slave MODE" is showed.
2.Press "ENTER" button, and "SLAVE" will be showed, then press ENTER to confirm.
Press "ENTER" and then press "UP" or "DOWN" to "Wireless rel".
Press "ENTER" and then press "UP" or "DOWN" to "Release +/-",and then long
CUSTOMER Mode-In this menu, you can select the AUTO program edited in the "EDIT" menu.
1. Press "ENTER" button and then UP or DOWN button until "CUSTOMER" is showed.
press "UP" or "DOWN" about 5-6 seconds. Until "clear is success" is showed. It
2. Press "ENTER" button, and there are 11 pre-programmed mode edited in the "EDIT" menu.
means release signal successfully.
EDIT Mode-In this menu, you can edit your desired AUTO program.
1. Press "ENTER" button and then UP or DOWN button until "EDIT" is showed.
DMX OUT
DMX IN
3
POWER
6
14
DMX address: 001
ID address: 01
Advertisement
Table of Contents
