Related Manuals for Stern Tubular HD 350030
Summary of Contents for Stern Tubular HD 350030
- Page 1 TUBULAR & eveR HAnd dRyeR I n s t a l l a t I o n a n d m a I n t e n a n c e g u I d e...
- Page 2 such...
-
Page 3: Technical Data
PAcK cOnTenTS TecHnicAL dATA TubuLAR HD TubuLAR HD 1 x Hand dryer and attachments Hose + 2 clamps 1 x Allen key 2.5mm 1 x Allen key 3mm 4 x screws & Ancors 1 x Allen key 7mm 1 x Hand dryer unit Tubular HD 350030 Tubular HD AISI316... - Page 4 PAcK cOnTenTS TecHnicAL dATA TubuLAR DP HD TubuLAR DP HD 1 x Hand dryer and attachments 4 x screws & Ancors Hose + 2 clamps 1 x Allen key 2.5mm 1 x Allen key 3mm 1 x Allen key 7mm Tubular DP HD 350020 4 x screws &...
- Page 5 PAcK cOnTenTS TecHnicAL dATA EVER HD EVER HD 1 x Hand dryer and attachments 1 x Allen key 2.5mm 1 x Allen key 3mm Hose + 2 clamps 1 x Allen key 7mm EVER HD 230510 4 x screws & Ancors 1 x Hand dryer unit...
-
Page 6: Pre-Installation Info
PRe-inSTALLATiOn infO inSTALLATiOn STeP 1 –inSTALL THe wALL UniT - TUBULAR Hd CHECK CONTENTS separate all parts from the packaging and check each part with the pack contents sec- tion. Pay attention to the variations of the different models. 29-33 mm Drill a 29-33 mm hole in the wall at the make sure all parts are accounted for before discarding any packaging material. - Page 7 inSTALLATiOn inSTALLATiOn STeP 1 –inSTALL THe decK UniT - eveR Hd Remove the 2 locking screws located on either side of the motor unit using Allen Recommended hole size key supplied. 33-36mm O-Ring Remove the hexagonal nut, the disk and gasket the gasket.
-
Page 8: Settings Adjustment
inSTALLATiOn SeTTingS AdjUSTmenT cOnnecTing OPen wiRe cABLeS DETECTIoN Loosen the screws to remove the DELAY oUT TImE RANGE exising cable. Loosen the screws TEmPoRARY oFF DELAY IN TImE FUNCTIoN Connect the hardwire cable. Remove and connect sELF ADJUsTmENT sECURITY TImE moDE cHAnging THe cABLe REsET... - Page 9 SeTTingS AdjUSTmenT SeTTingS AdjUSTmenT DELAY IN TImE: If required, the delay in time can also be modified in DETECTION RANGE: faucets as follows: This Hand Dryer was supplied with a self adjusting sensor. The ideal detection range for the specific Press the IN button.
-
Page 10: Maintenance
If a defect is found in normal use, Y. stern Engineering Ltd. will, at its discretion, repair, Any access to the dryer will be done only after it has been disconnected from provide a replacement part or product, or make appropriate adjustments. Damage the power supply. - Page 11 777 Passaic Avenue, Clifton NJ,07012, UsA Tel: +1-973 773 8011 | Fax: +1-973-779-8768 Toll Free: 1-800-4364410 info@sternfaucets.com | tech@sternfaucets.com 10.18 01500383-A...
Need help?
Do you have a question about the Tubular HD 350030 and is the answer not in the manual?
Questions and answers