Subscribe to Our Youtube Channel
Related Manuals for Stern SWAN 1010
Summary of Contents for Stern SWAN 1010
- Page 1 SWAN 1010 SWAN 1000 E L E C T R O N I C L A V A T O R Y F A U C E T SWAN SERIES I NSTALLATION AND MAIN TENA NCE G U IDE...
-
Page 2: Table Of Contents
INDEX TECHNICAL DATA PACK CONTENTS PRE-INSTALLATION INFO FAUCET INSTALLATION 8-11 SETTINGS ADJUSTMENT 12-13 BATTERY REPLACEMENT SPARE PARTS LIST MAINTENANCE Filters cleaning instructions Care and cleaning of chrome and special finishes LIMITED WARRANTY TROUBLE SHOOTING... -
Page 3: Technical Data
252400 SWAN 1010/ SWAN 1000: Internal battery Power supply SWAN 1010B/ SWAN 1000 B: 9V battery SWAN 1010 E/ SWAN 1000 E: 9V transformer Recommended water 0.5-8.0 bar (7-116 PSI) With water pressure of more than 8 bars, use pressure a pressure reducing valve for reduction. - Page 4 PACK CONTENTS SWAN 1010 Familiarize yourself with the part names and confirm that the parts are included. 1 x Allen Key 1 x Faucet and attachments B VERSIONS E VERSIONS 9V Battery box Transformer...
- Page 5 PACK CONTENTS SWAN 1000 Familiarize yourself with the part names and confirm that the parts are included. 1 x Allen Key 1 x Faucet and attachments B VERSIONS E VERSIONS 9V Battery box Transformer...
-
Page 6: Pre-Installation Info
PRE-INSTALLATION INFO CHECK CONTENTS Separate all parts from the packaging and check each part with the “Pack contents” section. Pay attention to the different models variations. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attempt to install your electronic faucet until you obtain the missing parts. - Page 7 FAUCET INSTALLATION STEP 1 – PREPARATION FOR MOUNTING THE FAUCET Shut off the water supply. Remove the hexagonal nut, the disk and the gasket. Do not remove the GASKET O-ring from the base of the faucet. DISC STEP 2 – INSTALLING THE FAUCET Place the faucet with O-ring into the hole in deck or lavatory.
- Page 8 STEP 4 – CONNECTING THE POWER SOURCE If your model is Swan 1010 \ Swan 1000: your product contains an internally mounted 9V battery. To activate it, proceed to clause # 2. If your model is Swan 1010 B \...
- Page 9 FAUCET INSTALLATION Remove the protective sticker from the sensor ABOUT Wait a few seconds before activating the faucet. If the range is unsatisfactory, refer to the section titled “Settings adjustment”. SECONDS...
- Page 10 SETTINGS ADJUSTMENT DETECTION RANGE DELAY OUT TIME TEMPORARY OFF DELAY IN TIME FUNCTION SECURITY TIME RESET RESET LOCK OUT TIME ADJUSTING THE SETTINGS WITH THE REMOTE CONTROL If necessary, the sensor settings can be adjusted as following: Shut off the water supply. In order to adjust the sensor with the remote control, hold the remote control straight in front of the sensor in a distance of about 6-8”...
- Page 11 SETTINGS ADJUSTMENT DETECTION RANGE: The sensor range is the greatest distance that an object can be away from the sensor to activate the faucet. The sensor is factory preset. To adjust the sensor range press + to increase detection range and – to decrease the detection range of the sensor.
- Page 12 Then press + to activate the hygiene flush or – to deactivate it. LOCK OUT TIME: It is possible to program a lock out time in Stern products upon request. This lock out time allows a user to activate the faucet, only after a specific amount of time has passed.
- Page 13 MANUAL SETTINGS ADJUSTMENT The sensor range is the range an object can be away from the sensor in order to activate the faucet. The sensor is factory preset. If necessary, it can be adjusted as follows: Disconnect the power supply, battery or transformer, from the sensor. Make a short circuit between the (+) and the (-) of the sensor.
- Page 14 When the battery weakens, the red indicator light will blink at a constant rate. The battery must be replaced within two weeks. To replace the battery at Swan 1010 \ Swan 1000 models: If your model is Swan 1000: Turn off the shut off valve (angle valve).
- Page 15 Be careful and make sure that you do not tear the o-ring. If torn replace it with Turn on the shut off valve (angle valve). a new one. To replace the battery at Swan 1010 B \ Swan 1000 B models: Replace the used battery Carefully...
-
Page 16: Spare Parts List
SPARE PARTS LIST Seals and Screws Kit for Swan 1010 models 07210001 Seals and Screws Kit for Swan 1000 models 07210029 Sensor kit for Swan 1010 & Swan 1000 07220001 Sensor kit for Swan 1010B\E & Swan 1000B\E 07220002 Solenoid valve kit... -
Page 17: Maintenance
MAINTENANCE Filter cleaning instructions This faucet is provided with one / two stainless steel filter(s) preventing foreign particles to enter the lines. If the water flow has decreased, this can be because the filter(s) is/are clogged. The filter(s) can be cleaned as follows: 1. - Page 18 If a defect is found in normal use, Y. Stern Engineering Ltd. will, at its discretion, repair, provide a replacement part or product, or make appropriate adjustments. Damage caused by accident, misuse, or abuse is not covered by this warranty.
-
Page 19: Trouble Shooting
TROUBLESHOOTING PROBLEM INDICATOR CAUSE SOLUTION No water 1. Sensor flashes coming out continuously of the faucet: when user’s Low battery. Replace battery hands are within the sensor’s range. 2. Red light 1. Range is too short. Increase the range in the sensor 2. - Page 20 15 Gan Rave Blvd., 81222 Gan Rave, Yavne, Israel Tel: 972-8-9326000, Fax: 972-8-9326025, export@sternfaucets.com www.sternfaucets.com 02.14 015410658-B...
Need help?
Do you have a question about the SWAN 1010 and is the answer not in the manual?
Questions and answers