Panasonic GP-X Series Instruction Manual page 2

Sensing range
The sensing range is specified for the standard
sensing object (Stainless steel/iron).
With a metal other than the metals specified in
the specifications, multiply with the correction
coefficient shown in the table below.Check the
effect with the actual machine.
Parts name and functions
4
Operation Panel
1
2
3
10
4
LO GO HI
12
set
TIMING
5
6
MODE ENTER
Sensor head connection
7 8 9 11
connector
No.Description Function
The measurement, calculated
value, setting data and so on are
Digital
displayed.
display
The measurement is displayed in
1
(green,
green on the lower line with the
orange)
GO judgment, while it is
displayed in orange on the upper
line with the HI or LO judgment.
HI
Lights up if the measurement is
indicator
2
larger the upper limit value.
(Orange)
Lights up if the measurement is
GO
between the upper and lower
indicator
3
limit values.
(Green)
Lights up if the measurement is
LO
smaller than the lower limit
indicator
4
value.
(Orange)
TIMING
Lights up at the timing of an
indicator
5
external or internal trigger.
(Green)
Lights up in the setting mode,
MODE
while it is not lit during
indicator
6
measurement.
(Orange)
Starts the setting mode.
Returns to the original state in
7 MODE key
the setting mode.
8 DOWN key
Use these keys to select the
setting value and setting items.
9 UP key
Moves among setting digits.
10 SHIFT key
Determines the setting item and
11
ENTER key
setting value.
Resets the controller forcibly to
zero (reference position) with the
current detection position to shift
12 0-set key
the display and analog voltage
output.
5 Operation System
Display/confirmation
Detection state
Upper limit value
Lower limit value
Averaging
frequency
Application mode
Option RS-232C
communication setting
BCD output unit setting
Controller communication
unit setting and address
setting
Controller communication
unit setting calculation
setting
Setting upon replacement
of sensor head
Software version display
Correction coefficient table
Sensor head
GP-X3SE GP-X5SE
GP-X8S GP-X10M
GP-X12ML GP-X22KL
Metal
Stainless steel (SUS304), iron
Aluminum
External I/O
Terminal block
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18
RS-232C connector
Sensor cable length
selection switch
Terminal
Indication Name Description
No.
A signal is output if the
1 LO LO output measurement is smaller than
the lower limit value.
A signal is output if the
measurement is between the
2 GO GO output
upper and lower limit values.
A signal is issued if the
measurement is larger than the
3 HI HI output
upper limit value.
Output
4 Common Common
COM
A signal is output if an error
5 ALARM Alarm output
occurs.
An internal trigger outputs for
6
STROBE Strobe output
measurement interval.
A signal is sent to another controller
Interference
for removal of effects caused by
prevention
7 INT P OUT
output interference.
8 Analog ground
GND
Analog The measurement is output in
ANA
an analog voltage.
output LOG
Analog voltage
9 OUT
output
The current detection position is
Zero setting
forcibly zeroed (to become a
10 0 SET
input
reference position).
One among four settings is
Memory
11
1
called up from the internal
switch 1
MEM
memory to replace the current
Memory
ORY
12 2
setting with it.
switch 2
Common Common
13 COM
Input
Measurement begins.
14 TIMING Timing input
Reset Temporarily finishes the
15 RESET
input
holding interval.
With a signal sent from another
Interference
controller, effects caused by
prevention
16
INT P IN
interference are removed.
input
Power
17 0V
supply 0V
Power
Supply power.
supply
Power supply
18 24V DC
24V DC
Setting mode
Memory number selection
Upper limit value
Lower limit value
Averaging frequency
Application mode
Indication varies according to the
*
mode selected in the application
mode. The figure on the left
indicates what is displayed with the
selection of the manual mode.
Set 1
Select the object to
be detected
Calibration
Judgment output setting
Display scale
Analog voltage
output scale
Display setting
Interference
prevention setting
Memory switching
method setting
Initialization to factory
shipment settings
I/O Circuit
6
NPN Type(GP-XC S,GP-XC M ,GP-XC KL)
D
1
T
0.5 approx.
Z
T r
3
Z
D4
T r
4
Z
D5
T r
5
Z
D6
T r
6
47
+
-
NPN output type: 0V
PNP output type: 24V
Internal circuit
Symbol...D , D
1 2
Z to Z
D1 D6
Tr to Tr
1 6
PNP Type(GP-XC S-P,GP-XC M -P,GP-XC KL-P)
D
1
T r
1
Z
D1
T r
2
Z
D2
T
r
3
Z
D3
T r
4
Z
D4
T r
NPN output type: 0V
PNP output type: 24V
47
Internal circuit
Symbol...D , D
1 2
Z to Z
D1 D6
Tr to Tr
1 6
Operating Conditions for Compliance with CE
7
arking / UKCA Marking
M
When using as a product in conformity with EMC Directive (2014/30/EU) /
EMC Regulation (2016/1091), observe the following requirements and conditions.
The controller must be connected within 10m of the power supply.
The Signal cable connected to the controller must be shorter than 30m.
A ferrite clamp must be mounted within 10mm of the base of the single connector of the
cable (GP-XBCC3) for the BCD output unit.
Panasonic Industry Co., Ltd.
Panasonic Industrial Devices SUNX Co., Ltd.
https://panasonic.net/id/pidsx/global
Please visit our website for inquiries and about our sales network.
Panasonic Industrial Devices SUNX Co., Ltd. 2022
September, 2022
Terminal No.
1
V
18
Comparison
Load
Z
output LO
D1
1
T
r
1 Load
100mA
Z
Comparison output GO
D2 max.
2 Load
r
2
100mA max.
Comparison output HI Load
D3
3
Load
100mA max.
Alarm output
5
100mA max.
Strobe output
6
100mA max.
7 Interference prevention output
Output common
4
0V
17
47
9 Analog voltage output: 5 to 5V (Note 1)
Analog ground
8
24V
5k
Zero setting input
10
24V
5k
Memory switch input 1 (Note 2)
11
24V
5k
Memory switch input 2 (Note 2)
12
24V
5k
Timing input
14
24V
5k
Reset input
15
24V
5k
Interference
16
*1 *2 *1
prevention input
Input common
13
(0V)
Users' circuit
: Reverse supply polarity
protection diode
: Surge absorption zener diode
: NPN output transistor
Terminal No.
V
18
Output common
4
100mA max.
1
Comparison output LO
100mA max.
2
Comparison output GO
100mA max.
Load
3
Comparison output HI
100mA max.
Load
5
Alarm output
Load
100mA max.
5 6 Load
Z Strobe output
D5
Load
T r Interference
6
7
Z prevention output
D6
17
0V
47
Analog voltage output: 5 to 5V (Note 1)
9
8 Analog ground
Input common ( 24V)
13
*1 *1 *1 *2 *1
5k Zero setting input
10
Memory switch input 1
5k
(Note 2)
11
5k
Memory switch input 2 (Note 2)
12
5k
Timing input
14
5k Reset input
15
5k
Interference prevention input
16
Users' circuit
: Reverse supply polarity
protection diode
: Surge absorption zener diode
: PNP output transistor
Notes: 1) Devices connected to the
analog voltage output
(terminal No. and ) must
have 1M or larger input
impedance.
2) To perform memory switching
24V DC
10%
by means of an external
terminal, select "Ext" as the
memory switching method.
For details, refer to section
"4.8 Memory Switching
Method Setting" .
Memory switching input (Note 2)
Memory No. Memory switch 1 Memory switch 2
0 High High
1
Low High
2 High Low
3 Low Low
Low: 0 to 4V, High: V or open
*1
Non-voltage contact or
NPN open-collector transistor
or
Zero setting input,
memory switch input 1/2
Reset input
Low (0 to 4V): Valid
High ( V or open): Invalid
*1 *1
*2
NPN open-collector transistor
Timing input
Low (0 to 4V): Valid
High ( V or open): Invalid
Notes: 1) Devices connected to the
analog voltage output
(terminal No. and ) must
have 1M or larger input
impedance.
2) To perform memory switching
24V DC
10%
by means of an external
terminal, select "Ext" as the
memory switching method.
For details, refer to section
"4.8 Memory Switching
Method Setting".
Memory switching input (Note 2)
Memory No. Memory switch 1 Memory switch 2
Low Low
0
Low
High
1
2 Low High
High
3 High
Low: 0V or open, High: 17 to 24V
*1
Non-voltage contact or
PNP open-collector transistor
or
Zero setting input,
memory switch input 1/2
Reset input
Low (0V or open): Invalid
High ( 17 to 24V): Valid
*2
PNP open-collector transistor
Timing input
Low (0V or open): Invalid
High ( 17 to 24V): Valid
PRINTED IN JAPAN