Do you have a question about the NEC370 Series and is the answer not in the manual?
Questions and answers
Gary Reid Cooper
February 11, 2025
Cannot get the dust cup to remove - I **** pushing on the green bar every way possible>
1 comments:
Mr. Anderson
February 12, 2025
To remove the dust cup from the Eureka NEC370 Series vacuum: 1. Press the dust cup release button to remove the handle component. 2. Rotate the motor cover component to detach the dust cup component.
This answer is automatically generated
Marsha Morrow
April 15, 2025
I am unable to twist the motor component back onto the dust cup. As you can see it is slightly off and not in the locked position.
Page 1
Cordless Stick Vacuum Cleaner Owner’s Guide Thank you for purchasing your new Eureka vacuum! Important instructions For easy assembly, please take a few moments to read this owner’s guide. If you have questions about your new vacuum, please contact our customer service HELPLINE at 1-800-282-2886.
24. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care. 25. The appliance should be stored, used and charged at a temperature range 40°F~104°F. SAVE THESE INSTRUCTIONS RISK OF INJURY. BRUSH MAY START UNEXPECTEDLY. DISCONNECT MOTORIZED FLOOR NOZZLE BEFORE CLEANING OR SERVICING. Household use only. www.eureka.com...
What comes in the box Handle On/o trigger Dust cup Hand vacuum release button Wand Motorized nozzle List of accessories Charger Crevice Tool 2-in-1 Furniture Brush Eureka Customer Service HELPLINE 1-800-282-2886...
2. Do not use and store the battery in an environment below 40°F~104°F. 3. When you dispose of this product, please remove the battery from the machine. 4. lt is strictly forbidden to modify the machine, accessories, adapter or battery www.eureka.com...
The rear of the hand vac is Insert the wand inserted into the wall mount component into the and is to hang vertically as motorized nozzle until you shown. Accessories are also hear a "click" sound. stored on the wall mount. Eureka Customer Service HELPLINE 1-800-282-2886...
Show two dots lit Rolling brush Show H1 discharge state anomaly High suction Show three dots lit Motor failure/ Show H2 discharge state Motor not and go o connected in 20 seconds Over Show 00 discharge and go o requires in 3s www.eureka.com...
Page 8
3. The crevice tool can be used to clean in tight spaces, crevices, between cushions and inside the motor vehicle. Eureka Customer Service HELPLINE 1-800-282-2886...
4.Remove the filter cotton from the cyclone cone, and then Filter take out cyclone cone from the dust cup component. cotton Cyclone cone Dust cup 5. Rotate and lift up the plastic cover, take out the cyclone for cleaning. www.eureka.com...
Page 10
2. Remove the brush roller lock as shown to remove the brush roller. 3. Take out the brush roller from the slot and then clean it up. 4. After cleaning or replacement, assemble in the reverse order of disassembly and reset the lock of brush roller. Eureka Customer Service HELPLINE 1-800-282-2886...
30 minutes before attempting to use the vacuum again. 2) After the 30 minute period, press the power button. lf the vacuum still does not work, call the Eureka Customer Service HELPLINE at 1-800-282-2886.
What Eureka will do: What Eureka will do: Eureka will, at its option, repair or replace a defective Battery Module or Eureka will, at its option, repair or replace a defective vacuum or vacuum battery part that is covered by this warranty. Repairs may be performed part that is covered by this warranty.
Need help?
Do you have a question about the NEC370 Series and is the answer not in the manual?
Questions and answers
Cannot get the dust cup to remove - I **** pushing on the green bar every way possible>
To remove the dust cup from the Eureka NEC370 Series vacuum:
1. Press the dust cup release button to remove the handle component.
2. Rotate the motor cover component to detach the dust cup component.
This answer is automatically generated
I am unable to twist the motor component back onto the dust cup. As you can see it is slightly off and not in the locked position.