Related Manuals for Albalá Ingenieros CWS2016C01
Summary of Contents for Albalá Ingenieros CWS2016C01
- Page 1 CWS2016C01 SIXTEEN CHANNELS OPTICAL MULTIPLEXER/DEMULTIPLEXER FOR CWDM Version 1.0 Albalá Ingenieros, S.A. 10 November 2016 - © Albalá Ingenieros S.A. - All rights reserved Medea, 4 - 28037 Madrid - Spain...
- Page 2 CWS2016C01...
-
Page 3: Table Of Contents
CWS2016C01 SIXTEEN CHANNELS OPTICAL MULTIPLEXER/DEMULTIPLEXER FOR CWDM Version 1.0 1. DESCRIPTION ........................5 1.1. The CWS2016C01 .......................... 5 1.2. Features ............................. 6 1.3. Block diagram ..........................7 2. SPECIFICATIONS ......................... 9 3. INSTALLATION ........................11 3.1. Initial inspection .......................... 11 3.2. - Page 4 CWS2016C01...
-
Page 5: Description
Albalá Ingenieros manufactures an electrical-to-optical port, the EOP2000, that together with the CWS2016C01 can be used to create an access point via a sole fiber optic cable for multiple electrical format digital video signals in a single 2 RU 19'' rack mounting frame. -
Page 6: Features
Albalá Ingenieros | Manual CWS2016C01 1.2. Features • Passive optical multiplexer or demultiplexer • Each optical connection can function as an input or as an output. • Manages 16 grid wavelengths as per ITU-T G.694.2. • One sole optical connection for the multiplexed signal. -
Page 7: Block Diagram
Albalá Ingenieros | Manual CWS2016C01 1.3. Block diagram... - Page 8 Albalá Ingenieros | Manual CWS2016C01 CWS2016C01...
-
Page 9: Specifications
Albalá Ingenieros | Manual CWS2016C01 2. SPECIFICATIONS Optical Connector LC/PC with multimode or monomode fiber Return loss >45 dB Operating wavelength 1271, 1291, 1311, 1331, 1351, 1371, 1391, 1411, 1471, 1491, 1511, 1531, 1551, 1571, 1591 y 1611 nm Bandwidth >13 nm (0,5 dB) - Page 10 Albalá Ingenieros | Manual CWS2016C01 CWS2016C01...
-
Page 11: Installation
If the CWS2016C01 receives optical signals from Class 1 sources at each one of its inputs as per IEC 60825-1 then the optical output may exceed the limit set by Class 1. -
Page 12: Environmental Considerations
1 - Remove the cover panel at the front of the selected slot and the slot directly to the right in order to install the CWS2016C01 into the mounting frame. 2 - Insert the CWS2016C01 module into the front of the mounting frame. The edges of the card slide into two plastic guides inside the mounting frame. -
Page 13: Interconnection
Albalá Ingenieros | Manual CWS2016C01 3.5. Interconnection The arrangement of the front panel connectors of the CWS2016C01 module is shown in the following figure. Front panel of the CWS2016C01 The optical connectors that provide access to the multiplexer/demultiplexer at LC/PC type. - Page 14 Albalá Ingenieros | Manual CWS2016C01 The minimum radius for any curvature in typical fiber optic cabling (ITU-T G.652) is normally 30 mm. If smaller radius are required, then reduced radius cabling should be used (ITU-T G.657).
-
Page 15: Operation
4. OPERATION 4.1. Functional description The CWS2016C01 is a passive device that does not need an external energy input. However, for the purpose of inventory it contains a small electronic circuit for verification of the product code, serial number and its position in the mounting frame. -
Page 16: Module Remote Control And Supervision
Software for simple configuration and supervision with a GUI for multiple modules can be downloaded from the Albalá Ingenieros website. The only remote function that can be performed with the CWS2016C01 is identification of the model number and the serial number. - Page 17 Albalá Ingenieros | Manual CWS2016C01 VERSION 1.X...
- Page 18 Albalá Ingenieros | Manual CWS2016C01 CWS2016C01...
-
Page 19: Glossary
Albalá Ingenieros | Manual CWS2016C01 5. GLOSSARY Small Form-factor Pluggable. A specification that defines the size, format and electrical characteristics of a class of modules typically employed to convert data signals from electrical to optical format, from optical to electrical format and transmission of those signal over fiber optics. - Page 20 Albalá Ingenieros | Manual CWS2016C01 CWS2016C01...
-
Page 21: Regulations
Albalá Ingenieros | Manual CWS2016C01 6. REGULATIONS IEC 60825-1 (2008) Safety of laser products, Part 1: Equipment classification, requirements and user's guide. ITU-T G.652 (2009) Characteristics of a single-mode optical fibre and cable. ITU-T G.657 (2012) Characteristics of a bending-loss insensitive single-mode optical fibre and cable for the access network. - Page 22 Albalá Ingenieros | Manual CWS2016C01 CWS2016C01...
-
Page 23: Versions
Albalá Ingenieros | Manual CWS2016C01 7. VERSIONS Ver. Date Description 10-06-2014 Preliminary Version 10-11-2016 First version... - Page 24 Albalá Ingenieros, S.A. Medea, 4 - 28037 Madrid Spain +34 913274453 www.albalaing.com info@albalaing.com...
Need help?
Do you have a question about the CWS2016C01 and is the answer not in the manual?
Questions and answers