Related Manuals for Albalá Ingenieros ATG3000C01
Summary of Contents for Albalá Ingenieros ATG3000C01
- Page 1 ATG3000C01 AUDIO TONE GENERATOR Version 1.0 Albalá Ingenieros, S.A. 21 December 2016 - © Albalá Ingenieros S.A. - All rights reserved Medea, 4 - 28037 Madrid - Spain...
- Page 2 ATG3000C01...
-
Page 3: Table Of Contents
ATG3000C01 AUDIO TONE GENERATOR Version 1.0 1. DESCRIPTION ........................5 1.1. The ATG3000C01 ..........................5 1.2. Features ............................. 5 1.3. Block diagram ..........................6 2. SPECIFICATIONS ......................... 7 3. INSTALLATION ........................9 3.1. Initial inspection ..........................9 3.2. Safety instructions ......................... 9 3.3. - Page 4 ATG3000C01...
-
Page 5: Description
The ATG3000C01 is a TL3000 terminal line module and can be housed in a three rack unit (3 RU) UR3000 mounting frame or a 1 RU UR3100 mounting frame. -
Page 6: Block Diagram
Albalá Ingenieros | Manual ATG3000C01 1.3. Block diagram... -
Page 7: Specifications
Albalá Ingenieros | Manual ATG3000C01 2. SPECIFICATIONS Analog audio signal output Connector Plug-in terminal, 3.81 mm pitch Impedance 73 Ω ± 1 % Type Active balanced Number of outputs 2 per channel, 2 channels Difference between a 600 Ω loaded output and an unloaded output... - Page 8 Albalá Ingenieros | Manual ATG3000C01 ATG3000C01...
-
Page 9: Installation
ELECTROSTATIC DISCHARGE. Always use antistatic bags clearly identified with a high degree of shielding for storage and transportation. The ATG3000C01 module is composed of two parts: one ATG3000P01 main board and one ATG3000P02 rear board. Both parts must be installed in a UR3000 or UR3100 mounting frame following the instructions in the corresponding section of this chapter. -
Page 10: Environmental Considerations
3.4. Power considerations The UR3000 and UR3100 mounting frames can house as many ATG3000C01 modules as will fit in them. 3.5. Module configuration In addition to mechanical installation of the module into a mounting frame, several program jumpers must be set to select the output signal levels. -
Page 11: Level Selection
10 dBu when switch 5 of S1 is set to ''OFF''. 3.6. Installing the module in the mounting frame The steps needed to install the ATG3000C01 module with the rear board in the mounting frame are: 1 - Disconnect all power cords from the power supplies of the mounting frame. - Page 12 INSTALLATION section of this manual. 6 - Insert the ATG3000P01 board (main board of the ATG3000C01 module) into the front of the mounting frame. The edges of the card slide into two plastic guides inside the mounting frame.
-
Page 13: Interconnection
Albalá Ingenieros | Manual ATG3000C01 3.7. Interconnection The following figure shows the ATG3000C01 module rear board connector layout. Rear view of the ATG3000C01 The ATG3000C01 module generates two independent audio tone signals (OUTA(L) and OUTB(R)) and distributes them to two outputs (OUTPUT 1 and OUTPUT 2). - Page 14 Albalá Ingenieros | Manual ATG3000C01 ATG3000C01...
-
Page 15: Operation
Albalá Ingenieros | Manual ATG3000C01 4. OPERATION This section describes the significance of the front panel indicators of the ATG3000C01 module and their remote control and monitoring ability. 4.1. Front panel description The appearance of the front panel and the elements it contains are shown in the following illustration. -
Page 16: Module Remote Control And Supervision
Albalá Ingenieros | Manual ATG3000C01 4.2. Module remote control and supervision The ATG3000C01 CANNOT be remotely controlled or supervised. -
Page 17: Glossary
Albalá Ingenieros | Manual ATG3000C01 5. GLOSSARY Logarithmic measurement to express ratios of power. Logarithmic measurement referring to 0.7746 V which is the voltage that dissipates 1 mW (0 dBm) of power when applied to a 600 ohm resistor. - Page 18 Albalá Ingenieros | Manual ATG3000C01 ATG3000C01...
-
Page 19: Regulations
Albalá Ingenieros | Manual ATG3000C01 6. REGULATIONS... - Page 20 Albalá Ingenieros | Manual ATG3000C01 ATG3000C01...
-
Page 21: Versions
Albalá Ingenieros | Manual ATG3000C01 7. VERSIONS Ver. Date Description 13-06-2013 Preliminary Version 21-12-2016 First version... - Page 22 Albalá Ingenieros, S.A. Medea, 4 - 28037 Madrid Spain +34 913274453 www.albalaing.com info@albalaing.com...
Need help?
Do you have a question about the ATG3000C01 and is the answer not in the manual?
Questions and answers