Viking Designer DFRD144D Use & Installation Manual
Refrigerated drawer
Hide thumbs
Also See for Designer DFRD144D:
- Specification sheet (5 pages) ,
- Dimensions (1 page) ,
- Energy manual (1 page)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Viking Designer DFRD144D
Summary of Contents for Viking Designer DFRD144D
- Page 1 Viking Use/Installation Guide Refrigerated Drawer...
-
Page 2: Important - Please Read And Follow
Retain for Future Reference IMPORTANT - PLEASE READ AND FOLLOW • Before beginning, please read these instructions completely and carefully. • Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. • Please observe all local and national codes and ordinances. •... - Page 3 UNDERCOUNTER CABINET CUTOUT 24” (61.0 cm)* Min. 34 1/2” (87.6 cm) Max. 35 1/8” (89.2 cm) 24” (61.0 cm) SPECIFICATIONS/DIMENSIONS PROFESSIONAL SERIES Basic Electric Data •115 VAC/60 Hz •Maximum amps - 3.3 •Approximate Shipping Weight - 180 lbs. (81.8 kg) 47 1/4”...
-
Page 4: Front View
SPECIFICATIONS/DIMENSIONS DESIGNER SERIES Basic Electric Data •115 VAC/60 Hz •Maximum amps - 3.3 •Approximate shipping weight - 180 lbs (81.8 kg) Side View 30 3/4” (78.1 cm) 47 1/4” (120.0 cm) 22” (55.9 cm) 24 3/8” (61.9 cm) 25 3/8” ( 64.5 cm) Front View 23 7/8”... -
Page 5: General Information
GENERAL INFORMATION Unpack 1. Remove banding from bottom of carton. Lift carton up and off of the unit. 2. Remove all tape and packaging material from the outside and inside of the cabinet. 3. Keep all carton packaging until your unit has been thoroughly inspected and found to be in good condition. AREA REQUIREMENTS Units Certified for Indoor Use - (black outer cabinet) MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS, SUCH AS WIND, RAIN, WATER (SPRAY OR... - Page 6 Step #1 1. A #10 pan head wood screw should be used to properly secure the overlay panel. A total of 8 screws will be needed. 2. Use only pan head screws. 3. Do not select a screw that is longer than the wood thickness of the screw locations.
- Page 7 Step #3 Sizing the Overlay Panel 15 3/16” (38.6 cm) 11 13/16” (30.0 cm) Step #4 Attaching the Overlay Panel to the Door 1. Set the overlay panel on drawer front face and align edges. Clamp panel in position and mark pilot hole locations. See Step #3 for nominal size and hole locations.
-
Page 8: Electrical Connection
ELECTRICAL CONNECTION WARNING Electrical Requirements A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time delay fuse or circuit breaker is recommended.) It is recommended that a separate circuit, serving only this appliance, be provided. •ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE. -
Page 9: Interior Light
The on/off key pad stops and starts the cooling of the unit. This can be used when your drawer refrigerator will not be used for extended periods of time. The LED light will continue to operate when the drawers are opened as long as the unit is connected to a power source. -
Page 10: Cleaning And Maintenance
CLEANING AND MAINTENANCE Any piece of equipment works better and lasts longer when maintained properly and kept clean. Condenser The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the cabinet. Spiders and insects can nest in and around the refrigerated drawer causing damage to the unit. -
Page 11: Diagnostic Led
DIAGNOSTIC LED In the back in the grille, there is a diagnostic/status LED. This LED is used to help diagnosis any problem with the unit and to tell its status. LED Status Not on or blinking Continuously on 1 blink and pause 2 blinks and pause 3 blinks and pause ENERGY SAVING TIPS... - Page 12 Any sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use during the third through the sixth year from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period.