Viking Designer DERT301-4B Installation Instructions Manual
Electric ranges/rangetops
Hide thumbs
Also See for Designer DERT301-4B:
- Specifications (5 pages) ,
- User manual (175 pages) ,
- Use & care manual (18 pages)
Advertisement
Table of Contents
INSTALLATION
INSTRUCTIONS
ELECTRIC RANGES/RANGETOPS
Retain for Future Reference
IMPORTANT: PLEASE READ AND FOLLOW
• Before beginning, please read these instructions completely and carefully.
• Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• Please ensure that this product is properly grounded.
• The installer should leave these instructions with the consumer who should retain for local inspector's use and for future
reference.
Installation must conform with local codes or in the absence of codes, with the National Electrical Code, ANSI/NFPA 70-latest edition.
In CANADA: Electrical installation must be in accordance with the current CSA C22.2 Canadian Electrical Codes Part 1 and/or local
codes.
GENERAL INFORMATION
WARNING
1.
: The use of cabinets for storage above the appliance may result in potential fire or burn hazard.
Combustible items may ignite, metallic items may become hot and cause burns. If a cabinet storage is to be
provided the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
W W A A R R N N I I N N G G
2.
: : This appliance shall not be used for space heating. This information is based on safety
considerations.
3. All openings in the wall behind the appliance in the floor under the appliance shall be sealed.
4. Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.
5. Disconnect the electric supply to the appliance before servicing.
6. When removing oven for service and/or cleaning, disconnect AC power supply.
7. Electrical requirements:
Listed in specifications chart. Electrical installation should comply with national and local codes.
This rangetop must be electrically grounded in accordance with local codes or, in the
absence of codes, with the National Electrical Code, ANSI/NFPA 70-latest edition. .
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
BACK TRIM ACCESSORIES
Assembly and installation instructions are included with all back trim accessories.
WARNING!!!
ELECTRICAL GROUNDING INSTRUCTIONS
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
Advertisement
Table of Contents
Related Manuals for Viking Designer DERT301-4B
Summary of Contents for Viking Designer DERT301-4B
-
Page 1: General Information
National Electrical Code, ANSI/NFPA 70-latest edition. . FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. BACK TRIM ACCESSORIES Assembly and installation instructions are included with all back trim accessories. WARNING!!! VIKING RANGE CORPORATION 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200... - Page 2 SPECIFICATIONS-ELECTRIC RANGETOP Description VERT301-4B Overall Width 29 7/8” (75.9 cm) Overall Height BASE HEIGHT To top of glass frame - 7 7/8” (20.0 cm) ADDITIONS TO BASE HEIGHT To top of island trim add 1 1/4” (3.2 cm) To top of backguard add 6” (15.2 cm) To top of high-shelf add 23 1/2”...
- Page 3 •Wall cabinets directly above product must be minimum 36” (91.4 cm) above cooking surface •Use range only with factory supplied legs. V V E E S S C C 3 3 0 0 6 6 - - 4 4 B B 29 7/8”...
-
Page 4: Proximity To Side Cabinet Installation
PROXIMITY TO SIDE CABINET INSTALLATION 1. This rangetop may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. IMPORTANT: : The top grate support MUST be 3/8” (.95 cm) above the adjacent base cabinet countertop. 2. The rangetop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36”... -
Page 5: Wood/Composite Overlay Installation
WOOD/COMPOSITE OVERLAY INSTALLATION (Including Custom Ventilator Installation) The bottom of a standard hood should be 30” (76.2 cm) min to 36” (91.4 cm) max above the ceramic glass surface. This would typically result in the bottom of the hood being 66” (167.6 cm) to 72” (182.9 cm) above the floor. Refer to the rangehood installation instructions for further information. -
Page 6: Final Preparation
REPLACEMENT PARTS Only authorized replacement parts may be used in performing service on the range. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician. - Page 7 YEL/VIO YEL/VIO GRAY 1800 WATT BRIDGE ELEM WHT/ORG 800 WATT BLACK 1800 WATT BLACK YEL/VIO White (H1a) GRAY BLK/WHT WHT/ORG BLACK W W A A R R N N I I N N G G - - T T H H I I S S U U N N I I T T M M U U S S T T B B E E G G R R O O U U N N D D E E D D . . S S E E E E I I N N S S T T A A L L L L A A T T I I O O N N I I N N S S T T R R U U C C T T I I O O N N S S F F O O R R P P R R O O P P E E R R G G R R O O U U N N D D I I N N G G P P R R O O C C E E D D U U R R E E S S N N O O T T E E : : T T R R A A I I L L E E R R S S O O R R S S T T R R I I P P E E S S W W I I L L L L B B E E T T H H E E S S E E C C O O N N D D C C O O L L O O R R I I N N A A C C O O L L O O R R C C O O M M B B I I N N A A T T I I O O N N...
-
Page 8: Range Installation
2. Measure from the floor to the bottom of the anti-tip opening located on the back of the range. Measured Dim. (A). 3. Locate the anti-tip bracket on the wall with the top left corner at the measured dimension plus 1/2” from the floor and the 5-5/8”... - Page 9 PROXIMITY TO SIDE CABINET INSTALLATION 1. This range may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. I I M M P P O O R R T T A A N N T T : : The top grate support MUST be 3/8”...
- Page 10 WOOD/COMPOSITE OVERLAY INSTALLATION The bottom of a standard hood should 30” (76.2 cm) min to 36” (91.4 cm) max above the ceramic glass surface. This would typically result in the bottom of the hood being 66” (167.6 cm) to 72” (182.9 cm) above the floor. Refer to the rangehood installation instructions for additional information.
- Page 11 Where local codes do not permit grounding through neutral, use a 4-wire power supply cord. the cord or conduit must be secured to the range with the strain relief bracket. The electrical connection is made at the terminal block, which is located behind the access door on the back of the range.
- Page 12 2. Remove strain relief mounting angle and reattach as shown. 3. Feed 1/2” (1.3 cm) trade size conduit through the hole in the bottom of the range back and secure to the strain relief bracket with a conduit clamp. 4. Feed line #1 (red 12 AWG/600v copper conductor), line #2...
- Page 13 Closely follow the procedures below to ensure proper performance and appearance of the range. 1. If the floor is smooth and level, level the unit with the screw thread of the legs. Set the high corner of the range so that the the top of the grate support is 3/8”...
-
Page 14: Performance Checklist
REPLACEMENT PARTS Only authorized replacement parts may be used in performing service on the range. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician. - Page 16 Viking Range Corporation 111 Front Street •Greenwood, Mississippi 38930 USA • (662) 455-1200 Specifications subject to change without notice. F1485L (PS0307VR)