Advertisement
Available languages
Available languages
2-gang wireless and batteryless lighting control
0 677 24L/74L/80L - CB0421/CT0421/CN0421
0 770 54L - 6 000 88L
5 742 89/96 - 5 743 25 - 5 748 38
7 418 12L/42L/72L
Requires to install the connected starter pack and one or more «... with Netatmo» connected switch, micromodule
or socket outlet.
Module Control
Gateway power outlet and home/
away wireless master switch
Or
Pack contents:
2-gang wireless and batteryless lighting control
Short push
ON/OFF1
Long push
Dim +25%
(2 short pushs
OFF1)
Stickers
x2
Short push
ON/OFF1
Long push
Dim -25%
(2 short pushs
OFF1)
Setup button
A
1
A
1
A
2
A
1
Tap 3 times the product to be controlled with the wireless, batteryless control. The light of the product to control flashes
rapidly.
A
2
For the specific case of the latching relay, press the main button of the latching relay until the configuration indicator
flashes slowly in blue, release it then tap the wired product you want to control 3 times with the wireless, batteryless
control. The indicator light of the product to be controlled flashes rapidly.
B
While holding the "setup" button on the wireless, batteryless control, briefly press the "ON" or "OFF" button of the chosen
side (1 or 2).
C
The indicator light of the product to control will briefly turn blue, and then will turn green again.The pairing was successful.
Check the correct pairing by pressing ON/OFF buttons
Multiple pairing: You can control several switches with the same wireless, batteryless switch by repeating the
operation for each product that you want to control.
c
Complete the installation
Or
Or
< 1 s
< 1 s
To complete your installation, briefly press the configuration of
the Module Control or the middle of the wireless Home / Away
or on the configuration button of the mobile
master switch
gateway power outlet
.
All the indicator lights on the products switch off
Mobile gateway
power outlet
Or
Short push
Long push
(2 short pushs
Short push
Long push
(2 short pushs
Frequency bands: 2.4 - 2.4835 GHz
Power level: < 20 mW
Do not remove
the cover plate
B
C
+
B
C
+
B
C
+
If necessary, erase the configuration of the
wireless, batteryless control (factory reset)
< 1 s
+
While holding the "setup" button on the wireless,
batteryless control, press the upper button for
5 seconds.
Confirm that your control is correctly reset by
making an ON command, then OFF
3
a
Start the configuration
Press the configuration button of Module Control or press the middle of the wireless master switch or on the
configuration button of the mobile gateway power outlet until its light briefly turns green, and then stop
pressing. All wired products lights will turn green.
> 3 s
ON/OFF2
Dim +25%
OFF2)
ON/OFF2
Dim -25%
OFF2)
b
Pair the wireless, batteryless switch to control the connected products (switch, micromodule,
socket-outlet, latching relay).
Make sure that the indicator lights on the wired products are green and not flashing. If not, go back to
precedent step.
1
www.legrandoc.com/067724L
LEGRAND - Pro and Consumer Service - BP 30076
87002 LIMOGES CEDEX FRANCE • www.legrand.com
Download the app
Your installation is ready. You can download the Legrand Home +
Control application to control your lights remotely.
FCC ID: 2ACN8-ZLGP1X
This device contains licence-exempt transmitter(s)/receiver(s) that comply with FCC RF and Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the device.
This device complies with FCC and ISED radiation exposure limits set forth for general population. This device must not be co-located or
operating in conjunction with any other antenna or transmitter.
FCC Caution: the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct
5 s
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Safety instructions
Make sure the power supply is disconnected before any intervention.
Strictly comply with instructions for installation and use.
Or
.
2
Put the stickers in place
Before fixing the wireless control(s) with
the removable stickers provided, test one
on a non-visible area of the wall.
You can also fix the wireless control(s) permanently to
the wall with screws.
The undersigned, Legrand declares that the radio-electric equipment type
(0 677 24L/74L/80L - CB0421/CT0421/CN0421 - 0 770 54L - 6 000 88L -
5 742 89/96 - 5 743 25 - 5 748 38 - 7 418 12L/42L/72L) complies with
directive 2014/53/EU. The full text of the EU declaration of conformity is
available on the following website: www.legrandoc.com
IC: 12132A-ZLGP1X
Or
> 3 s
H < 2 m
H > 2 m
Model : ZLGP18
Model: ZLGP18
Advertisement
