Yamaha DX11 Operating Manual page 21

(3)
Edit
Program Change
Table
The
Program Change
Table determines
what
DXll
memory
is
selected in
response
to
each incoming
Program
Change message.
To
edit
the
table,
answer
YES.
Use
the
PRESET C
and
PRESET D
switches
to step
through
the
incoming
PGM
1
PGM
128.
and
use the
DATA
ENTRY
switches to select a Internal
Voice
101
032,
Internal
Performance POl -P32. Cartridge
Voice
1-32
or
Cartridge
Performance
1-32.
(Cartridge
memories
are
indicated
by
a
"Cj".)
[20]
Exclusive
(1)
Exclusive off
/on
When
this
is
Off,
all
incoming System Exclusive
messages
(bulk data)
will
be ignored.
When
it
is
on.
you
can
re-
peatedly press
20
to select
the
following
jobs.
When
you
press
YES,
the selected bulk data
will
be transmitted
from
MIDI OUT.
fk This transmitted data
can
be received
by another
DXl K
a
TX81Z
or a
DX2
1/27/
100
(or
any
data storage
device
such
as the
MDFl)
if
the
Memory
Protect
(p.
7)
is
Off,
its
Exclusive
is
On, and
its
Receive Channel
matches
the
Transmit Channel
(p. 18).
For
details,
see
the
notes
on
data compability
on page
28.
(2)
Voice
Transmit
Press
YES
to
transmit 32
voices.
(Press
NO
to select
banks I/A/B/C/D.)
(3)
Performance Transmit
Press
YES
to
transmit 32 performances.
(4)
Setup
Transmit
Press
YES
to
transmit
the selected data.
(Press
NO
to
select
AL,SY,EF,MC.)
AL:
PC +
EF
+
MC
(see
below)
SY:
System
data.
The
settings for
Combine,
Mem-
ory Protect
(int, crt).
Receive Channel, Trans-
mit
Channel,
PgmChange,
Cont.
Change, Ex-
clusive,
Tune, PB, Note, ID,
MIDI,
Local,
Aftertouch,
Data
Entry Assign, Cartridge
Bank, Controller Reset,
Fixed
Velocity,
and
EG
Forced
Damp.
PC:
Program Change
Table
EF: Effect data (three types,
four of each)
MC: The two user-programmable micro
tuning
scales
[21]
Cartridge
Cartridge
Save
1.
[IT]
Press 21 to
get the
"Cartridge Bank"
dis-
Splay.
Use
the data entry slider to select a car-
tridge
bank
1A-16B.
3. [2j]
Press 21
again to get the "Cartridge Save^'
display.
%
4.
\N0\ Repeatedly
press
NO
to select the type
of
data to save.
^-
r^ES) Press
YES
to
save the selected data to
cartridge.
(CRT memory
protect
and
the
protect switch
on
the
cartridge
must
be
off.)
Cartridge
Load
1. \2\]
Press 21 to get the
"Cartridge Bank^"
dis-
Splay.
Use the data entry
slider to select a
car-
tridge
bank lA
16B.
3.
|
21
1
(twice) Press 21 twice to
get the "Cartridge
Load"
display.
4.
JNO|
Repeatedly
press
NO
to select
the type of
data
to
load.
5.
[Yes] Press
YES
to
load the selected
data
to
DXll
internal
memory.
(INT
memory
protect
must
be
off.)
Cartridge
Format
1.
\2\} (4
times) Press 21 four times to get the
"Cartridge
Format"
display.
2.
hL
Use
the
data entry slider to select a car-
^
tridge
bank
lA-
16B.
3.
[VESJ
Press
YES
to
format the selected cartridge
bank.
(CRT memory
protect
and the protect switch
on
the
cartridge
must
be
off.)
Details
of each operation are given
below.
Various data can be stored
in
a
RAM
cartridge
(sold
separately).
Repeatedly press 21 to step
through
the
four
jobs.
(1)
Cartridge
Bank
Select
The
RAM4
data cartridge
has only a
single
bank.
However,
future data cartridges
may
have up
to
1
6
banks,
each of which can contain
a different
type of
data.
An
entire set
of
DXll
data (32 Voices,
32 Performances,
Effects,
Program Change
Table
and System
data) oc-
cupies only half
of a cartridge
bank -A
or B.
Thus,
a
single
cartridge
could contain up
to
32 independent
sets
of
DXll
data.
Use
the
Data Entry
slider to select
bank
lA
16B.
(2)
Cartridge
Save
Repeatedly press
NO
to
select the
type of data
you want
to save.
You
have the following choices.
all:
32 voices
and 32 performances,
Program
Change
Table
settings. Effect data,
Micro Tune
data.
System Setup
data.
setAL:
Program Change
Table,
Effect data,
Micro
Tune
data.
setSY:
System data
(the settings for
Combine,
Memory
Protect,
Receive Channel, Transmit Channel,
Program Change, Control Change, and
Exclu-
sive
etc.).
19