Timer Recording Using Vcr Buttons - Panasonic Omnivision VCRplus+ PV-4611 Operating Instructions Manual

Cancel a Timer Recording:
Recording is in progress
1
2
Push the VCR POWER button to
release the VCR from timer mode.
Push the STOP button within 10
seconds of pushing the VCR POWER
button to cancel the recording.
The TIMER indicator goes out in the
Multi- Function display.
Replace Program Contents:
Recording is not in progress
1
Push the PROG
button to display all
currently set
programs.
P DT STRAT STOP CH SPD
8 10:00P 12: OOP 125 SLP
3 10 8:00P 9:00P P
4 SU $:00P 10:00P "t SPP
SELECT 1-8:ROTATE WHEEL
ENTER :PUSH WHEEL
Rotate and push the
Wheel to select and
enter the desired timer
recording.
(See page 16.)
Rotate and push the
Wheel to select and
enter replacement
information.
ELECT START DATE
BY ROTATING WHEEL
Push the PROG button to exit this mode
and return to the normai TV screen.
Review or Clear Program Contents:
Recording is not in progress
1
Push the PROG
button to display all
currently set
programs.
P DT STRAT STOP CH SPD
:00P
4 SU 9:00P 10:00P "t ste
Y 1-8:ROTATE WHEEL
:PUSH WHEEL
CANCEL :PUSH CLEAR KEY
program number. 2 8 10:00P 12:00P 125 SLP
IE i a
Push the CLEAR SELECT 1-8:ROTATE WHEEL
button to clear the ENTER :PUSH WHEEL
program. END ¡PUSH PROG KEY
Push the PROG button to exit this mode
and return to the normal TV screen.
€€09090909090909000000000000600000000090900000009000
- Timer Recording
J Using VCR Buttons
A timer recording can be set up using the buttons on the
VCR. If necessary, the clock can also be set.
POWER Multi Function REW PLAY FF REC/TIME
Display
W SELECTA SET PROGRAM
(1) O DEC MD START STOP CH
and BY SELECT A/*Y KEY
NAE Push FF to TO END PUSH PROG KEY
E) | enter the
program mode. ===
* Ifthe clock is not set, pushing these | 7I — ^ ^ DST:ON
buttons will display the SET CLOCK
screen. In this case, proceed with steps |8Y SELECT A/Y KEY
2 and 3 to set the clock and then steps |NEXT, PUSH SET KEY OR
2-6 to set a timer recording. J9 END FUSH FRO KEY
* Once the VCR is in the Program mode, the PLAY, REC, FF,
and REW buttons on the VCR operate only as specified above.
* Push REW or PLAY to
(2) ES or: C» make your selection.
* Push SET (FF) repeatedly to move to a
particular item for setting or correction.
(for c down (for up)
, Push FF to set
' and move on to
- the next item.
Items to be Set:
* recording DATE
* START time
* STOP time
* CH(annel), or LINE
* SPEED (SP, LP, SLP)
When the program is completed...
D o , Push REC/TIME
© and O
-and FF to display
(at the same ine"
; Program contents.
To set the next program,
repeat steps 2, 3, and 4 before continuing with step 5.
Se : Push REC/TIME and
© and e
FF to exit this mode.
(at the same time)
Og ued NOA 20N
r
t
b | Multi Function Display
* Itis not possible to clear a timer program using the VCR buttons.
Please use the Remote Control.
* When recording programs via a cable box, make sure the cable
box is left on and tuned to the desired channel.