Viking K-1900-7 Technical Practice page 3

P r o g r a m m
P r o g r a m m
A. Security Code
A six digit number may be used to access the programming mode. The security code has been factory set to 845464 (V-I-K-I-N-
G). It is recommended that you change the security code to a personal 6 digit number as follows:
Step 1. Access programming as shown in section B.
Step 2. Enter your new security code followed by #47.
Step 3. To exit programming simply hang up the K-1900-7.
Note:
B, 2. Programming Without Using the Security Code
B. Accessing the Programming Mode
1. Remote Programming
Step 1. Connect the green and red wires on the K-1900-7 to a C.O. line or analog PABX/KSU station.
Step 2. From a Touch Tone phone, call the line connected to the K-1900-7.
Step 3. Take the K-1900-7 off-hook (remove handset from the cradle). From the calling phone enter "
digit security code, factory set to 845464 (see section A above). A double beep will indicate that programming has
been entered.
Step 4. Program as shown in sections D - I.
Step 5. To exit programming, hang up both phones.
2. Programming Without Using the Security Code
Step 1. Connect the green and red wires on the K-1900-7 to a C.O. line or analog PABX/KSU station.
Step 2. K-1900-7: Place JP1 on pins 1 & 2 (see section C), K-1900-7-EWP: Set DIP switch 1 to ON.
Step 3. From a Touch Tone phone, call the line connected to the K-1900-7.
Step 4. Take the K-1900-7 off-hook (remove handset from cradle). A double beep should be heard indicating you have
entered programming.
Step 5. Program from calling phone as shown in sections D - I.
Step 6. K-1900-7: Place JP1 back on pins 2 & 3 (see section C), K-1900-7-EWP: Set DIP switch 1 back to OFF.
Step 7. To exit programming, simply hang-up the phones.
C. JP1 / DIP Switch Programming
DIP Switch
JP1
(K-1900-7) (K-1900-7-EWP)
1 - ON
Pins 1&2
1 - OFF
Pins 2&3
Note:
D. Programming Features Quick Reference
Speed dial number .................................................................................................................
, (anywhere in the speed dial number) .................................................................................
# (anywhere in the speed dial number) ..................................................................................
Set dialing speed to normal (Touch Tones: 120ms on/off, Pulse: 10 pps) (factory setting) .....
Set dialing speed to fast (Touch Tones: 50ms on/off, Pulse: 20 pps) ......................................
Block hand held pocket dialers (factory setting) ....................................................................
Allow hand held pocket dialers ..............................................................................................
Normal pre-dial pause (approximately 1.4 sec) (factory setting) ............................................
Short pre-dial pause (approximately 800 ms) ........................................................................
To add a one second pause at any point in the dialing string .................................................
To add a four second pause at any point in the dialing string .................................................
Toggle between Pulse and Touch Tone dialing (see section I) ...............................................
Change security code ............................................................................................................
To clear the speed dial number and return all programming to factory settings .....................
Note:
i n g
i n g
Description
Learn Mode
Normal Operation
(factory setting)
K-1900-7-EWP
OFF
,
,
MUST NOT
Internal View of
the K-1900-7
JP1
1 2 3
ON
JP1
1 2 3
1 2 3
OFF
#
,
" followed by the six
Internal View of
the K-1900-7-EWP
Enter Digits - then -
1-32 digit (0-9) +
,,
, #
, 1
, 2
, 3
, 4
,
5
,
6
#7
, 7
, 8
+
6 digits (0-9)
###
DIP
Switches
OFF ON
Memory
Location
# 00
#47