Advertisement
I
n
s
t
a
l
l
a
t
i
o
I
n
s
t
a
l
l
a
t
i
o
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the telephone line.
!
It is recommended that a surge protector be installed to protect against such surges. Contact Panamax at (800) 472-5555 or Electronic
Specialists Inc. at (800) 225-4876.
Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent condensation from
accumulating inside the E-30-PT always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4" diameter hole in the bottom of the gray
plastic box.
*Note: Peel off paper liner and adhere gasket to the back of the faceplate, centering it over the four corner mounting holes. Be careful to position the mod-
ular jack inside the chassis as not to damage the components on the circuit board.
Front View of
Plastic Rough-In
Box (included)
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
Important: The E-30-PT will NOT
mount to a standard double gang box.
Note: The plastic rough-in box (part # 259576) may be purchased separately
in advance. Go to www.vikingelectronics.com and click on "Spare Parts".
Analog
PABX/KSU
Station
C.O. Line
RJ11
or
* Note: To increase surge protection, loosen the PCB mounting screw labeled
from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)
** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082
inches. Do not strip wires prior to terminating.
P
r
o
g
r
a
m
m
P
r
o
g
r
a
m
m
A. Accessing the Programming Mode
The E-30-PT phone can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU station, or
a DLE-200B Line Simulator.
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).
Step 2. From a Touch Tone phone call the line attached to the E-30-PT.
Step 3. When the E-30-PT answers, enter the 6-digit security code (factory set to 845464 - see section C). A double beep
should then be heard indicating you have entered the programming mode.
2. Without the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).
Step 2. Move DIP switch 3 to OFF (incoming calls enter the programming mode without security code - see section F).
Step 3. From a Touch Tone phone call the line attached to the E-30-PT.
Step 4. When the E-30-PT answers, a double beep will be heard and you will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section F).
Note: If a valid memory position is entered, a double beep will be heard, four beeps indicate an error.
n
n
2.1"
* Adhere gasket to front panel,
centering over mounting holes
4.0"
5.0"
"Push to Talk" Button
Call Connected Red LED
"Call" Button
(4) 6-32 X 3/4" stainless steel, flat
head, hexdrive, screws (included)
Condensation Drain Hole
Rear View of a Standard
E-30-PT Phone
i
n
g
i
n
g
Need More Information on the DLE-200B?
?
Call (715) 386-4345 and select 605.
3.25"
5.22"
5.14"
Condensation
Drain Hole
Front View of Optional
2.25"
VE-5x5 (not included)
The optional VE-5x5 Surface Mount Box is designed
to be surface mounted to a single gang box, double
gang box or VE-GNP gooseneck pedestal (right).
Need More Information on VE-5x5 or VE-GNP?
?
Analog
PABX/KSU
Station
C.O. Line
Spade
Terminal
(included)
* Earth
Ground
(optional)
(as shown above) and fasten a wire with spade terminal (included)
(4) 0.38" diameter
(for gooseneck mounting)
3.81"
(4) 0.2 x 0.43 slots
for double gang box
(2) 0.2 x 0.43 slots
for single gang box
(1) .74" dia
3.0" 3.3"
3.0"
Rear View of VE-5x5
(not included)
Call (715) 386-4345 and select 424.
Rear View of an
E-30-PT-EWP Phone
** Gel-Filled
Butt
Connectors
(included)
Red
or
Green
10.50"
Side View of
VE-GNP
(not included)
39.5"
41.41"
Spade
Terminal
(included)
* Earth
Ground
(optional)
Advertisement
