Advertisement
C. DIP Switch Programming
1. Auto Answer Feature ON/OFF (DIP Switch 1)
DIP switch 1 is for turning the Auto Answer feature ON and OFF. The E-40 is fac-
tory set to auto answer when an inbound call is detected.
2. Dial Tone Detection ON/OFF (DIP Switch 2)
With DIP switch 2 in the ON position, if the E-40 detects more than 5 seconds of
continued dial tone, the unit will automatically disconnect. If the E-40 is installed
on a continuously noisy line, it may detect the noise as dial tone and automatical-
ly disconnect. If this happens, turn the dial tone detection (DIP switch 2) OFF.
3. Programming Mode ON/OFF (DIP Switch 3)
With DIP switch 3 in the OFF position, the E-40 is in the "Normal Operation Mode" (factory setting). By placing DIP switch 3 in the ON position,
the E-40's programming mode is enabled. The programming mode is used for adjusting the Call Length Time Out, Silence Time for automatic
disconnect and the Talk/Listen delay (VOX switching speed). These features are set from the factory and normally do not need adjustment. If
adjustment is necessary, see Programming sections D - I.
D. Accessing the Programming Mode
The E-40 can be programmed from any Touch Tone phone using a telephone line, Viking model C-200 or C-2000A Entry Phone
Controller, analog PABX/KSU station or a Viking model DLE-200B Line Simulator.
Step 1. Move DIP switch 1 to the ON position (sets unit to answer incoming calls - see section C).
Step 2. Move DIP switch 3 to ON (incoming calls automatically enter the programming mode - see section C).
Step 3. From a Touch Tone phone call the line attached to the E-40.
Step 4. When the E-40 answers, 2 beeps will be heard and you will automatically enter the programming mode.
Step 5. When finished programming, enter "0000" to exit programming and move DIP switch 3 back to OFF (see section C).
E. Quick Programming Features
Call length time out (1-9 minutes), 10 = disabled (factory set to 11111 = 5 minutes) .......................................
Silence time out for disconnect (10-90 seconds), 10 = disabled (factory set to 1111 = 40 secs) .....................
Talk/listen delay (VOX switching speed) 0.1 - 0.9 seconds (factory set to 111 = 0.3 secs) .............................
Forced hang-up command (used to exit programming and hang up the E-40) ..............................................
F. Programming Beeps
If a valid "Feature" is entered, a single beep will be heard and you will have 20 seconds to enter a "Time" value. If an invalid
"Feature" (five or more zeros) or forced hang-up command (four zeros) is entered, 3 beeps will be heard and the E-40 will hang up.
If a valid "Time" is entered 2 beeps will be heard and you will have 20 seconds to enter your next "Feature". If an invalid "Talk/Listen
Delay Time" is entered (10 or more ones), 3 beeps will be heard and you will have 20 seconds to enter your next "Feature".
G. Call Length Time Out
This feature selects the maximum length of time that calls can be connected.
Programmable in increments of 1 minute up to a maximum of 9 minutes. To dis-
able the call length time out, program ten ones in the "Time" value location.
With the call length disabled, the E-40 phone must rely on CPC, busy, silence
or return dial tone to hang-up. Use the chart at the right.
H. Silence Time Out
This feature selects the length of time that calls will remain connected without
voice activity. Programmable in increments of 10 seconds up to a maximum of 90
seconds. To disable the silence time out, program ten ones in the "Time" value
location. Use the chart at the right. * Note:
I. Talk/Listen Delay (VOX Switching Speed)
This feature selects switching time between talk and listen modes (VOX switching time). Use the chart above.
* Note:
O
p
e
r
a
t
i
o
n
O
p
e
r
a
t
i
o
n
When the push button is pressed, the E-40 phone goes off-hook, much like a standard speaker phone. In the event that the line is busy, the E-40 will
hang-up. The E-40 will also automatically hang up on CPC, silence, busy signal, return to dial tone or time out. If programmed to auto-answer (DIP switch
1 ON), the E-40 will also answer any incoming call.
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no respon-
sibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Fax Back Doc 187
Note:
Printed in the U.S.A.
DIP
Position
Description
Switch
1
ON
Auto-Answer ON *
OFF
Auto-Answer OFF
1
2
ON
Dial Tone Detection ON *
2
OFF
Dial Tone Detection OFF
ON
Programming Mode
3
3
OFF
Normal Operation Mode *
* Note:
Select
Wait for
Feature
Beep(s)
Time Value
0
beep
00
beep
000
beep
0000
3 beeps
Table A
Table A
Time
Call Length
Silence
Value
Time Out
Time Out
1
1 min
11
2 min
111
3 min
1111
4 min
11111
5 min*
111111
6 min
1111111
7 min
11111111
8 min
111111111
9 min
10 or more
Disabled
Disabled
Enter
Wait for
2 Beeps
111...
beep beep
111...
beep beep
111...
beep beep
Talk/Listen
Delay
10 sec
.1 sec
20 sec
.2 sec
30 sec
.3 sec*
40 sec*
.4 sec
.5 sec
50 sec
.6 sec
60 sec
70 sec
.7 sec
80 sec
.8 sec
90 sec
.9 sec
Error
Advertisement
