Advertisement
Quick Links
- 1 -
407 M
AXX
CENTER MOUNT LEGREST
with
FLOATING FOOT PLATFORM
F
CM L
IXED
EGREST
for the
and
P
CM L
OWER
EGREST
the
DEALER: This manual contains important instructions and safety information related to the
installation, set-up and adjustment of our Maxx Floating CM Legrests. These instructions are
for use only by trained /qualified technical personnel
TRD0569 Rev A
Advertisement
Related Manuals for Motion Concepts TRX 407 MAXX
Summary of Contents for Motion Concepts TRX 407 MAXX
- Page 1 - 1 - 407 M CENTER MOUNT LEGREST with FLOATING FOOT PLATFORM CM L IXED EGREST for the CM L OWER EGREST DEALER: This manual contains important instructions and safety information related to the installation, set-up and adjustment of our Maxx Floating CM Legrests. These instructions are for use only by trained /qualified technical personnel TRD0569 Rev A...
-
Page 2: Safety Symbols
If you are not certifi ed as an installer, please arrange immediately for training by a Motion Concepts technician or sales agent who has been certifi ed to teach the installation and set-up of the Maxx Floating CM Legrest. Every eff ort will be made to meet your training needs. - Page 3 WARNING! Risk of Injury or damage if correct or improper replacement (service) parts are used • Replacement parts for your power positioning system MUST match original Motion Concepts parts WARNING! Danger of accident and loss of warranty if maintenance is insuffi cient! •...
- Page 4 - 4 - rview 407 Maxx Floating CM Legrests: Assembly Ove 407 M FLOATING POWER CM LEGREST (shown with the Standard Foot Platform) FLOATING FIXED CM LEGREST (shown with the Basic Foot Platform) Individual Curved Calf Pads* Individual Curved Calf Pads* Standard CM Basic CM Foot Platform...
- Page 5 - 5 - rview 407 Maxx Floating CM Legrest - Installation Ove 3.1 CM LEGREST RECEIVERS (GENERAL INSTALLATION ADJUSTMENT) The Maxx Legrest Receivers are installed into the Center Mount Crosstube using one of two possible mounting hardware confi gurations (refer to Fig. 1. and Fig. 2. below). The mounting hardware will vary depending on the date of manufacture.
- Page 6 - 6 - rview 407 Maxx Floating CM Legrest - Installation Ove 3.2. FLOATING CM LEGREST (INSTALLATION DEPTH ADJUSTMENT) Installation of the 407 Maxx Floating CM Legrests, and minor legrest Depth Adjustments, are controlled via the Maxx Legrest Receivers at the front of the seat frame Ultra-Rails. WARNING! Risk of Serious Injury, Damage or Loss of Stability.
- Page 7 - 7 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment 4.0 FLOATING CM LEGREST SET-UP & ADJUSTMENTS: The 407 Maxx Power Positioning System (PPS) off ers a unique Floating CM Legrest design, which allows the foot platform to collapse* when it contacts the ground, to assist with forward transfers. The 407 Maxx PPS can be equipped with a Floating Fixed Center Mount (CM) Legrest, or a Floating Power CM Legrest.
- Page 8 - 8 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment 4.1 INITIAL LEGREST ANGLE (S The initial (retracted) legrest angle may be set to one of four optional confi gurations. The mounting holes used in the upper legrest crosstube will establish the initial legrest angle (refer to Fig. 1. below). Please Note: the initial (retracted) legrest angle will determine the fi...
- Page 9 - 9 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment 4.2 KNEE-TO-HEEL (KTH) LENGTH ADJUSTMENTS: IMPORTANT! To avoid potential injury, property damage and/or damage to the legrest/seating system, it is critical that the legrest KTH length (and anterior limit switch), is properly adjusted to ensure the necessary ground clearance is maintained during the anterior tilt function.
- Page 10 - 10 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment 4.2.2 KTH A CM L The Maxx Floating Power CM Legrest off ers an adjustable knee-to-heel (KTH) length, ranging from 13.5” (34cm) - 17.5” (44cm). Adjustments are available in 1/2” (13mm) increments. The KTH length is adjusted via the adjustment screws on the legrest extension brackets (1 screw per bracket).
- Page 11 - 11 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment 4.3 FLOATING CM LEGREST- FOOT PLATFORM ADJUSTMENTS: NOTE: the fi nal angle of the foot platform will also be dictated by the initial legrest angle set up of the 407 Maxx Floating CM Legrest- see Section 4.1 4.3.1 S CM F The angle of the center mount platform is determined by an adjustable button head screw at the rear of the...
- Page 12 - 12 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment 4.3.3 F -U F Both the Basic and Standard CM Foot Platforms are designed to be ‘fl ipped-up’ to provide additional clearance at the front of the wheelchair, if necessary. The fl ip-up adjustment is performed by manually lifting the foot platform until it reaches the upright/perpendicular position (as illustrated in the images below).
- Page 13 - 13 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment B. CURVED CALF PAD HEIGHT ADJUSTMENT: Mounting Plate Adjustment*: The overall height/position of the curved calf pads on the Maxx Floating Fixed CM Legrest and/or the Maxx Floating Power CM Legrest can be adjusted via the calf pad mounting plate (both pads are adjusted simultaneously).
- Page 14 - 14 - 407 Maxx Floating CM Legrest - Set-Up/Adjustment 4.4.2. O The One-Piece Calf Panel is non-adjustable, and installed directly onto the downtube of the upper CM Legrest weldment. The calf panel incorporates a removable fabric covered foam pad, which off ers a larger surface area for added comfort and increased leg support.
- Page 15 - 15 - NOTES:...
- Page 16 CANADA Motion Concepts LP Tel (local): 905-695-0134 84 Citation Drive, Unit 1 Tel (toll free): 866-748-7943 Concord, Ontario Fax: 905 695 0138 L4K 3C1 Tech Service: 800-680-4191 info@motionconcepts.com www. www.motionconcepts.com Motion Concepts 700 Ensminger Rd, Suite 112 Tel.: 716-447-0050 Tonawanda, New York...
Need help?
Do you have a question about the TRX 407 MAXX and is the answer not in the manual?
Questions and answers