Security Code - Viking K-1900-8 Technical Practice

3. Accessing the Programming Mode Remotely
Step 1. Call into the C-2000A from a Touch Tone phone. Note:
Step 2. Answer the call from any house phone (device) connected to terminals 4 & 5, LINE OUT TO PHONES.
Step 3. From either phone enter ,# followed by the six digit security code (factory set to 845464, see Programming section C).
Step 4. A double beep will indicate that you have accessed the programming mode.
Step 5. You can now Touch Tone program the features listed in section B below.
Note:
B. Quick Programming Features
Privacy Number (factory disabled) .......................................................................................
Entry phone 1 keyless entry codes (factory disabled) ...........................................................
* Entry phone 1 one time use keyless entry codes (factory disabled) ...................................
Entry phone 2 keyless entry codes (factory disabled) ...........................................................
* Entry phone 2 one time use keyless entry codes (factory disabled) ...................................
Entry phone 3 keyless entry codes (factory disabled) ...........................................................
* Entry phone 3 one time use keyless entry codes (factory disabled) ...................................
Entry phone 4 keyless entry codes (factory disabled) ...........................................................
* Entry phone 4 one time use keyless entry codes (factory disabled) ...................................
Master keyless entry codes (factory disabled) ......................................................................
* Master one time use keyless entry codes (factory disabled) ..............................................
Doorstrike 1 activation time (.5 - 99 secs, factory set to 00 = .5 secs) ...................................
Doorstrike 2 activation time (.5 - 99 secs, factory set to 00 = .5 secs) ...................................
Doorstrike 3 activation time (.5 - 99 secs, factory set to 00 = .5 secs) ...................................
Doorstrike 4 activation time (.5 - 99 secs, factory set to 00 = .5 secs) ...................................
** Auxiliary Contacts:
Auxiliary contact timing
1. Entry phone triggered timed activation (factory setting, DIP switch 1 off) ...................
2. Entry phone triggered continuous activation ..............................................................
3. Entry phone triggered ring cadence activation ...........................................................
4. Auxiliary input triggered timed activation ....................................................................
Maximum entry phone ring count (1 - 99 rings, factory set to 5 rings) ..................................
Enable entry phone ringing (factory setting) ........................................................................
*** Disable entry phone ringing ............................................................................................
Security code (factory set 845464) ......................................................................................
Enable entry phone Caller ID (factory setting) .....................................................................
Disable entry phone Caller ID ..............................................................................................
Entry phone calls give custom double ring cadence (factory setting) ...................................
Entry phone calls give standard ring cadence ......................................................................
Dial "9" to access an outside line ..........................................................................................
Instant outside line access (factory setting, for use with private dial tone) ............................
Enable doorstrike latching commands (factory setting) ........................................................
Disable doorstrike latching commands .................................................................................
Enable entry phone identifier beeps (factory setting) ..........................................................
Disable entry phone identifier beeps ....................................................................................
Reset all programming to factory default settings ................................................................
* Note:
** Note:
DIP Switch Programming
*** Note:
C. Security Code
This six digit number can be used to access the programming mode. The security code has been factory set to 845464
(V-I-K-I-N-G). It is recommended that you change the security code to a personal 6 digit number. To change the secu-
rity code, access programming (see Programming section A). Enter six digits 0-9 followed by #47. If you have forgot-
ten your security code, follow the steps in Programming section A, 2. Accessing the Programming Mode Locally
(Security Code Bypass Mode). Note:
(.5 - 99 secs, factory set to 00 = .5 secs, DIP switch 1 off)
EITHER
D
Enter Digits
0-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
4-6 digits (0-9)
2 digits (00-99)
2 digits (00-99)
2 digits (00-99)
2 digits (00-99)
................. 2 digits (00-99) .....
1 ...........................
2 ...........................
3 ...........................
4 ...........................
2 digits (01-99)
1
0
6 digits (0-9)
,
1
,
2
,
3
,
4
,
5
,
6
,
7
,
8
,
9
,
0
###
C-2000A Auxiliary Contact Mode
Memory
Location
- then -
+
#00
+ #11 - #16
, ,
+ #11 - #16
+ #21 - #26
, ,
+
#21 - #26
+
#31 - #36
, ,
+ #31 - #36
+ #41 - #46
, ,
+
#41 - #46
+
#51 - #56
, ,
+
#51 - #56
+ #19
+ #29
+
#39
+
#49
+ ......
#59
+ ...... #60
+ ...... #60
+ ...... #60
+ ......
#60
+
#61
+
#62
+ #62
+ #47
NOT
,
5