Page 1
2019/05/27 19:43:09 (GMT+09:00) HISTORY INFORMATION FOR THE FOLLOWING MANUAL: SERVICE MANUAL (COMMON) SERVICE MANUAL (COMMON) GN1S CHASSIS Segment: SE2 Version Date Subject 03/2015 Issue. 04/2015 Correction on Model Names ( pg3 ) , Update on pg62 ~ 94 . 09/2015 Additional Hotel Information: 1.
Page 2
2019/05/27 19:43:09 (GMT+09:00) SERVICE MANUAL (COMMON) SERVICE MANUAL (COMMON) GN1S CHASSIS Segment: SE2 LCD TV LCD TV SYS SET...
Page 3
2019/05/27 19:43:09 (GMT+09:00) MODEL LIST THIS SERVICE MANUAL CONTAINS COMMON INFORMATION FOR BELOW REGIONS AND MODELS: REGION ASIA ASIA EUROPE EUROPE MODEL KLV-32R4*C KDL-40R4*C KDL-32R4*C SYS SET...
8) Use care when handling the wires or connectors of the inverter circuit. 8) Use care when handling the wires or connectors of the inverter circuit. components with Sony parts whose part numbers appear as shown in this components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony.
2019/05/27 19:43:09 (GMT+09:00) Safety Notes 1-3. Caution About the Lithium Battery 3) Measuring the voltage drop across a resistor by means of a VOM or battery 1) Danger of explosion if battery is incorrectly replaced. Replace only with operated AC voltmeter. The 'limit' indication is 0.75V so analog meters must the same or equivalent type.
2019/05/27 19:43:09 (GMT+09:00) Safety Notes 1-7. Lead Free Information Please hold reinforcement board and Please pull out FFC while pushing the The circuit boards used in these models have been processed using Lead plunge it to depths. button of both ends at the same time. Free Solder.
2019/05/27 19:43:09 (GMT+09:00) Self Diagnostic Function SECTION 2 SELF DIAGNOSTIC FUNCTION 2-1. Overview of Control Buttons 2-3. LED Pattern When safety shutdown occurs, Standby LED display reports the cause by using the lightning patterns as indicated below 3.0sec 3.0sec 0.5sec 0.5sec Example: The figure above shows LED display when SHUTDOWN is caused by Audio Error.
2019/05/27 19:43:09 (GMT+09:00) Self Diagnostic Function 2-5. Triage Chart No Picture No Sound Blinking UI OK Reference Main UI NG Tuner USB Video Component HDMI SCART Video Component Tuner HDMI SCART USB Speaker Speaker ...
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting SECTION 3 TROUBLESHOOTING 3-1. General 3-2. No Power B* Board Type Size ASIA EUROPE START 32” No Power 40” Does the Power Led Open Detail stay on when the B-Board - No Power TV is switched on ? •See DDCON See DDCON Check DC voltage at...
Page 11
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-2. No Power 3-2-1. DD Con Start DDCON B-Board B-Board Fuse Check voltage at JL005 Check fuse. 3.3V? F6000 B-Board Check voltage at Check voltage at Change B- BE JL008 board BA JL6015 1.2V? B-Board B-Board Check voltage at : Change B- Change B- Check voltage at JL6016...
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-3. Standby LED Blinking 3-3-1. 2 times blinking 2 times Blinking B-Board Check DC voltage at Change B-board JL6001 19V - 19.5V? Ensure that +ve probe is touching the touching the needle. Adaptor Take out adaptor and check the output voltage. Change B-board 19V –...
Page 15
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-3. Standby LED Blinking 3-3-2. 3 times blinking START 3x blinking Speaker Impedance ≠ 6~8 Ω Remove No 3x blinking Speaker Connector Check Speaker harness at CN4001 & perform at CN4001 & perform And Speaker impedance And Speaker impedance AC OFF - ON 3x blinking No connectivity for speaker harness...
Page 16
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3x LED Blinking - BA board Photo 3x LED Blinking BA board Photo CN4001 CN4001 F4000 IC4001 SYS SET...
Page 17
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3x LED Blinking - BA board Layout 3x LED Blinking BA board Layout CN4001 F4000 IC4001 SYS SET...
Page 18
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3x LED Blinking - BE board Photo 3x LED Blinking BE board Photo CN4001 F4000 IC4001 C 00 SYS SET...
Page 21
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-3. Standby LED Blinking 3-3-4. 5 times blinking START 5x Blinking Happens TV Boots Up TV Boots Up Reinsert LVDS Flat Normally Incorrect FFC Normally Replace B-Board Flexible Cable (FFC) at B* Board and B* Board Issue Panel Side. Make sure FFC is Insertion taped properly.
Page 22
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-3. Standby LED Blinking 3-3-5. 6 times blinking 6x blinking 6x blinking Check harness at CN9000 Check harness at CN9000 Connect Harness and try again Check F9000 continuity Check F9000 continuity Change B*board Change Check voltage at CL9000 Re-download SW board Perform this...
Page 23
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting X6 Standby LED Blinking : Board Layout X6 Standby LED Blinking : Board Layout CN9000 Backlight harness Figure 1: CN9000 location CL9003 CL9003 CL9000 CL9000 CL9000 F9000 F9000 Figure 2: LED Driver Circuit portion in BA board Figure 3: LED Driver Circuit portion in BE board SYS SET...
Page 24
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-3. Standby LED Blinking 3-3-6. 7 times blinking START 7x blinking Assist Speaker Remove Impedance ≠ 6~8 Ω Impedance ≠ 6 8 Ω No 7x blinking Ch No 7x blinking A i t S Assist Speaker Connector Check Assist Speaker harness k A i t S k A i t S at CN4505 &...
Page 25
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 7x LED Blinking - KK board Photo 7x LED Blinking KK board Photo F4500 IC4505 CN4505 CN4505 F4501 SYS SET...
Page 26
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 7x LED Blinking - KK board Layout F4500 IC4505 CN4505 F4501 SYS SET...
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-4. No Picture 3-4-1. General No Picture BL_ON Check +12V Input Still No Check Input Source: Check Input Source: PANEL VCC SW PANEL_VCC_SW CHECK BL ON on CHECK BL_ON on Picture Picture -Tuner Replace LVDS FFC B-Board at CL9012. +12V voltage at C8601 (BA) / HIGH (+3.3V): OK...
Page 29
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio 3-5-1. General Main Speaker Main Speaker Main Speaker Main Speaker Refer Refer Audio Problem Audio Problem No Sound? No Sound? “Main Speaker No Sound” Headphone (HP) Out Headphone (HP) Out Refer No Sound? No Sound? “HP Out No Sound” Video/Component or HDMI 2 Audio In Video/Component or HDMI 2 Audio In Refer...
Page 30
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio START 3-5-2. Main Speaker No Sound Main Speaker No Sound Sound Do a Factory Setting No Sound No connectivity for speaker harness Sound Check Speaker Harness Change Speaker Harness connectivity No Sound No Sound Speaker Impedance Sound ≠...
Page 31
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting Audio Problem - Main Speaker No Sound (BA board Photo) Audio Problem Main Speaker No Sound (BA board Photo) F4000 IC4001 IC4001 SYS SET...
2019/05/27 19:43:09 (GMT+09:00) Audio Problem - Main Speaker No Sound (BA board Layout) F4000 IC4001 SYS SET...
Page 33
2019/05/27 19:43:09 (GMT+09:00) Audio Problem - Main Speaker No Sound (BE board Photo) Audio Problem Main Speaker No Sound (BE board Photo) F4000 IC4001 C 001 SYS SET...
Page 34
2019/05/27 19:43:09 (GMT+09:00) Audio Problem - Main Speaker No Sound (BE board Layout) F4000 F4000 IC4001 IC4001 SYS SET...
Page 35
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio 3-5-3. Headphone (HP) Out No Sound Headphone (HP) Out No Sound START START No Sound No Sound Sound Sound Do a Factory Setting Do a Factory Setting No Sound No Sound Sound Sound Check AV Setup Check AV Setup Check AV Setup, Check AV Setup,...
Page 36
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting Audio Problem - Headphone (HP) Out No Sound (BA board Photo) IC5000 IC4000 J4000 SYS SET...
Page 37
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting Audio Problem - Headphone (HP) Out No Sound (BA board Layout) IC4000 J4000 IC5000 SYS SET...
Page 38
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting Audio Problem - Headphone (HP) Out No Sound (BE board Photo) Audio Problem Headphone (HP) Out No Sound (BE board Photo) IC5000 IC4000 J4000 SYS SET...
Page 39
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting Audio Problem - Headphone (HP) Out No Sound (BE board Layout) IC4000 J4000 IC5000 SYS SET...
Page 40
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio START START 3-5-4. Analog Audio Input No Sound No Sound No Sound Sound Sound Do a Factory Setting Do a Factory Setting No Sound No Sound Sound Sound Check correct Source mode is selected No Sound No Sound Sound Sound...
Page 41
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio START 3-5-5. Analog RF No Sound Do a Factory Setting S tti Sound Sound RF cable, OK? Change RF cable No Sound No Sound Sound Sound RF source, OK? Change RF source/channel No Sound No Sound Raster sound, OK? Refer “Speaker No Sound”...
Page 42
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio * Please refer to IM for supported HDMI 3-5-6. HDMI Audio No Sound audio format. START Do a Factory Setting Sound Sound HDMI cable, OK? Change HDMI cable No Sound No Sound Sound Sound HDMI source, OK? Change HDMI source/channel No Sound No Sound...
Page 43
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio START START 3-5-7. USB No Sound Do a Factory Setting Do a Factory Setting Sound Sound USB device, OK? USB device, OK? Change USB device No Sound No Sound Sound Sound USB source, OK? USB source, OK? Change USB source/channel No Sound No Sound...
Page 44
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio START START 3-5-8. Scart (In) No Sound (BE board only) No Sound No Sound Sound Sound Do a Factory Setting Do a Factory Setting No Sound No Sound Sound Sound Check correct Source mode is selected No Sound No Sound Sound...
Page 45
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio 3-5-9. Scart (Out) No Sound (BE board only) START START No Sound No Sound Sound Sound Do a Factory Setting Do a Factory Setting No Sound No Sound Sound Sound Check correct Source mode is selected No Sound No Sound Sound...
Page 46
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting Audio Problem - Scart (In/Out) No Sound (BE board Photo) Audio Problem Scart (In/Out) No Sound (BE board Photo) CN3001 IC4200 IC4200 SYS SET...
Page 48
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-5. Audio 3-5-10. Audio Problem (KK-board) 3-5-11. Audio Problem -Assist Speaker No Sound START Sound Sound Refer Do a Factory Setting Audio Assist Speaker “Assist Speaker Problem No Sound? No Sound” No Sound No Sound No connectivity for No connectivity for speaker harness Sound...
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-6. Video Problem 3-6-1. Video Analog Signal Path SYS SET...
Page 50
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-6. Video Problem 3-6-1. No Picture AEP/UK Destination (BE) (a) SCART RGB No Picture AEP/UK N Pi t No Picture Check RGB_SWITCH [LOW : Detailed check all parts Check CN3001 IC5000 Y12 at RGB_SWITCH signal Connection [SOY1] at R3055 Path [VD3016/R3053] [HIGH: 0.4V ...
Page 51
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-6. Video Problem 3-6-1. No Picture AEP/UK Destination (BE) (b) SCART CVBS SCART CVBS N Pi t No Picture AEP/UK AEP/UK No Picture Check RGB_SWITCH Check CN3001 [HIGH] IC5000 Y12 Connection Connection [SOY1] at R3055 OK [LOW] Detailed check all parts at RGB_SWITCH signal Path [VD3016/R3053] Path [VD3016/R3053]...
Page 52
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-6. Video Problem 3-6-1. No Picture AEP/UK Destination (BE) (c) Video No Picture No Picture AEP/UK Check J3001 Check if input OSD Connection, is GREY OUT VIDEOB DET VIDEOB_DET OK if it is highlighted At R3015 Detailed check all parts NG (Vpp: 0 V) Check wave between at CVBS1P signal path...
Page 53
2019/05/27 19:43:09 (GMT+09:00) Troubleshooting 3-6. Video Problem 3-6-1. No Picture AEP/UK Destination (BE) (d) Component No Picture AEP/UK No Picture No Picture Check J3001 Check if input OSD VIDEOB_DET at is GREY OUT R3015, OK if it is highlighted AV COMP SEL at AV_COMP_SEL at Detailed check all parts R3014...
Page 57
2019/05/27 19:43:09 (GMT+09:00) 3-6. Video Problem 3-6-2. No Picture WW Destination (BA) (a) Video No Picture No Picture WW Check J3001 Check if input OSD Connection, is GREY OUT VIDEOB DET OK if it is highlighted OK if it is highlighted At R3015 Detailed check all parts NG (Vpp: 0 V) Check wave between...
Page 58
2019/05/27 19:43:09 (GMT+09:00) 3-6. Video Problem 3-6-2. No Picture WW Destination (BA) (b) Component No Picture WW No Picture Check J3001 Check if input OSD VIDEOB_DET at is GREY OUT is GREY OUT R3015, OK if it is highlighted AV_COMP_SEL at Detailed check all parts R3014 at signal path of: Y0P : [VD3004/R3004/R3007/...
2019/05/27 19:43:09 (GMT+09:00) 3-9. TUNER 3-9-1. NO SOUND: TUNER This troubleshooting is only for Analog No Sound with normal picture Only RF tuner input? Please refer Audio Check IC5000 (SoC) Check IC5000 (SoC) troubleshooting troubleshooting SYS SET...
Page 103
2019/05/27 19:43:09 (GMT+09:00) 3-9. TUNER 3-9-2. NO PICTURE: @ TUNER RF input no picture / noisy picture picture Check RF source cable Change RF cable and antenna and antenna, OK? Check Tuner power line: Please refer DDCON 3.3V at JL1035 = 3.3V? troubleshooting troubleshooting 1.8V at JL1004 = 1.8V?
Page 106
2019/05/27 19:43:09 (GMT+09:00) 3-9. TUNER 3-9-3. FOR 12V LNB Voltage Checking: @ AEP_T2S2 12V LNB Voltage Checking Check fuse F1000 at MOSFET Q6014 Check Tuner power line Check Panel_PWR signal line 12V line. broken 12V at JL003 = 12V? at CL6021 = 3.3V? Please change fuse if NG Please refer DDCON troubleshooting...
Page 107
2019/05/27 19:43:09 (GMT+09:00) BE BOARD EU T2S2 (A Side) CL6021 F1000 F1000 SYS SET...
Page 108
2019/05/27 19:43:09 (GMT+09:00) 3-9. TUNER 3-9-4. FOR ANALOG TUNING: @ All destination For LA-ISDB(BR/AR) , LA-T2(COL) Notes: Notes: Analog Tuning - Parts for IFOUTN1 line: C1013,FB1000,C1011, R1061, C1027,R1055, R1057. For Other destination - Parts for IFOUTP1 line: Confirm ANT or Cable connection C1015,FB1001,,C1012,R1062,C1028, R1062, R1056, - Parts for IFAGC1 line: C1017,R1049, R1050, C1029, R1058.
Page 111
2019/05/27 19:43:09 (GMT+09:00) 3-9. TUNER 3-9-5. FOR DIGITAL TUNING 1: @ AM-ATSC(MX/UC). Notes: Digital Tuning 1 - Parts for IFOUTN1 line: C1013,FB1000,C1011, R1061, C1027,R1055, R1057. - Parts for IFOUTP1 line: C1015,FB1001,,C1012,R1062,C1028, R1062, R1056, Confirm ANT or Cable connection - Parts for IFAGC1 line: C1017,R1049, R1050, C1029, R1058. - Parts for M_SCL line: R5027.
Page 113
2019/05/27 19:43:09 (GMT+09:00) 3-9. TUNER 3-9-6. FOR DIGITAL TUNING 2: @ AEP-T2S2, PA_T2, CH, LA-ISDB(BR/AR) and LA-T2(COL). Digital Tuning 2 Notes: - Parts for M_SCL line: R5027. For AEP-T2S2 For LA-ISDB(BR) and - Parts for M_SDA ine: R5016 LA-T2(COL) only - Parts for DEMOD TSCLK line:R1029 - Parts for DEMOD_TSDATA line: For PA_T2 and -R1030,R1031, R1032,R1033, R1034,R1035, R1036...
Page 116
2019/05/27 19:43:09 (GMT+09:00) 3-10. Tact Key 3-10-1. Switch Unit Buttons Switch Unit NOT FUNCTIONING *VOLTAGE LEVEL FOR EACH PRESSED BUTTON Voltage (average) Voltage range Check Wire Harness 0.00 – 0.2 0.000 Change Wire Harness And Connector And connect properly 1.00 – 1.22 1.114 Connection? CH/Input...
Page 117
2019/05/27 19:43:09 (GMT+09:00) Probe point for switch unit Front of Switch unit Back of Switch unit Pin 3 Pin 2 Pin 1 SYS SET...
Page 118
2019/05/27 19:43:09 (GMT+09:00) 3-11. IR 3-11-1. Troubleshooting flow TV cannot be controlled TV cannot be controlled by remote commander by remote commander Green LED blinks at Power indicator Green LED blinks at Power indicator Green LED lights up Green LED lights up Mechanical when using commander when using commander...
Page 119
2019/05/27 19:43:09 (GMT+09:00) Probe point for BE board Probe point SYS SET...
Page 120
2019/05/27 19:43:09 (GMT+09:00) Probe point for BA board Probe point SYS SET...
Page 121
2019/05/27 19:43:09 (GMT+09:00) 3-12. CI 3-12-1. Troubleshooting flow Check if TV can detect CICAM Check CI or CI+ case Channel Setup Digital Setup Change B Board CA Module Valid key Check any pin on Check service menu for CI Slot is bend or CI+ Credentials ...
Page 122
2019/05/27 19:43:09 (GMT+09:00) Check CI 5V CI 5 Volts, PIN 17/18/51/52 SYS SET...
Page 123
2019/05/27 19:43:09 (GMT+09:00) Check CI Detection Pin Both CI Detection Pin should be 3.3V before CICAM insert and 0v when CICAM inserted. Card Detect 1 – PIN 36 Card Detect 2 – PIN 67 SYS SET...
Page 124
2019/05/27 19:43:09 (GMT+09:00) Check CI Routing Confirm these 7 network resistor is mount properly. SYS SET...
Page 125
2019/05/27 19:43:09 (GMT+09:00) 3-13. USB 3-13-1. Troubleshooting flow Ensure No USB Main IC NG device connected Change B Board 3.3V Check IC7001 Pin 17 3.3V 3 3V 3.3V Check IC7002/IC7003 IC7002/IC7003 NG Check USB 5V Pin 4 Change B Board IC7005/IC7001 NG Change B Board SYS SET...
Page 126
2019/05/27 19:43:09 (GMT+09:00) Check USB 5V US 5 CN7002/CN7001 Pin1 SYS SET...
Page 128
2019/05/27 19:43:09 (GMT+09:00) Check USB 5V US 5 IC7002/IC7003 Pin4 SYS SET...
Page 129
2019/05/27 19:43:09 (GMT+09:00) 3-14. Ether 3-14-1. Troubleshooting flow Check if TV has good cable connection Set-up Network setup F il d Failed Check if any abnormal Check if the Ethernet Connector NG or broken point on cable is good Change B Board Ethernet Connector Ethernet Connector Check if TV has MAC Address...
Page 130
2019/05/27 19:43:09 (GMT+09:00) 3-15. Wifi-Module 3-15-1. Troubleshooting flow START Does WiFi function Open Detail turned on at TV? - Turn On WiFi Device Can Open Detail Be Connected? - Hardware Defect SYS SET...
Page 131
2019/05/27 19:43:09 (GMT+09:00) 3-15. Wifi-Module 3-15-2. Turn On WiFi Turn On WiFi TV UI: Is the radio field HOME -> SETTINGS -> Open Detail Strength too weak SYSTEM SETTING -> Network Setting - Hardware Defect or even No signal? SETUP SETUP -> Wi-Fi SETUP -> >...
Page 132
2019/05/27 19:43:09 (GMT+09:00) 3-15. Wifi-Module 3-15-3. Hardware Defect Input Power Hardware Defect TP: Vcc = 5V Check harness Check harness connection insertion connection insertion is OK is OK Connect properly Connect properly Loose harness Loose harness between WiFi and Bxx Change harness between Bxx board Main Harness Back View...
2019/05/27 19:43:09 (GMT+09:00) SECTION 4 SERVICE ADJUSTMENTS 4-2. Accessing Software Version. 4-1. Accessing Service Mode. 1) Go to TV standby condition by remote commander. 1) Press (Enter) or button on Remote to enter status information. 2) Press “i+ (info)”, “5”, “Volume +” then “TV power” on remote. You can see Service Mode on display.
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 4-3. Accessing Self Diagnostic History. 4-4. Accessing Self Diagnostic Menu. 1) Go to TV standby condition by remote commander. 1) Press (Enter) button on Remote to enter Self Check Mode. 2) Press “i+ (info)”, “5”, “Volume -” then “TV power” on remote. 3) T E it 3) To Exit –...
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 4-5. Accessing Serial Number Edit 1) Press button on Remote to edit Serial Number. Screen Sample Remote Commander Note: * The font color of YES is change to black when it is selected. 4) If 4) If YES i YES is selected, the input data is saved into EEPROM.
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 5) If NO is selected, the input data is not saved into EEPROM. 4-6. Accessing Model Name Edit. The serial number that has been input is displayed. User can still edit the Serial Number. 1) Press button on Remote to edit Model Name. Remote Commander Screen Sample Screen Sample...
Page 137
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 3) Model Name can be set ONLY ONCE. After user input data , press <Enter>. Pop dialog will appear to inform user to confirm data. button to select YES or NO button to select YES or NO. Press Press Select YES if input data is correct.
Page 138
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 4 7 White Balance 4-7. White Balance 1) Press button on Remote to enter White Balance Adjustment. Remote Commander Screen Sample 2) Press button to to change intended Color Temp adjustment.(Cool , Neutral and Warm) Remote Commander Screen Sample SYS SET...
Page 139
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment Start WB adjustment by changing R/G/B Gain & Offset register. R/G/B Gain setting around High luminance Adjustment (Default Value 512) R/G/B Offset setting around Low luminance Adjustment (Default Value 0) Screen Sample After adjustment completed go to Data Save and press until it shows “W/B” and press enter. l t d t D t S ...
Page 140
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment Remark#1 For this case only Cool Color Temp. will be saved to TV set. To save Neutral and Warm adjustment we need to change Color Temp. to intended Color temp adjustment and execute Data Save operation again After operation temp.
Page 141
2019/05/27 19:43:09 (GMT+09:00) Remark #2: Data Recall only will reset current Color Temp. data to default. For this case only Cool Color Temp. will be reset to TV set. To reset Neutral and Warm adjustment we need to change Color Temp to intended Color temp and adjustment we need to change Color Temp.
2019/05/27 19:43:09 (GMT+09:00) Diagrams 5-2. Block Diagram 5-2-1. BA SE-2 (PAA)- KLV-* UART Rx/Tx UART Rx/Tx Bus Switch Bus Switch D+/D-(1) or Rx/Tx NLAS7242 NLAS7242 Indicator LED/SIRCS D+/D- (1) USB2.0 Port backlight backlight 60Hz 60Hz Switch Unit (4keys) LED Driver BD9397EFV HDMI 2 *HDMI/MHL *(MHL) for PAA-India only receiver...
Page 144
2019/05/27 19:43:09 (GMT+09:00) Diagrams 5-2. Block Diagram 5-2-2. BA SE-2 (PAD)- KDL-* D+/D-(1) or UART Rx/Tx Bus Switch Bus Switch Rx/Tx NLAS7242 NLAS7242 Indicator LED/SIRCS D+/D- (1) USB2.0 Port backlight backlight 60Hz 60Hz Switch Unit (4keys) LED Driver BD9397EF HDMI 2 LVDS MT5565 MT5565 HDMI1 (ARC)
Page 145
2019/05/27 19:43:09 (GMT+09:00) Diagrams 5-2. Block Diagram 5-2-3. BE SE-2 (EU) D+/D-(1) or UART Rx/Tx Bus Switch Bus Switch Rx/Tx Rx/Tx NLAS7242 NLAS7242 Indicator LED/SIRCS D+/D- (1) USB2.0 Port 1 backlight backlight 60Hz 60Hz PCMCIA Switch Unit (4keys) P P - - TS LED Driver BD9397EFV P P - - TS...
Page 155
2019/05/27 19:43:09 (GMT+09:00) How to update TV for Service Update APPENDIX-1 How to update TV Software (1) Please download TV firmware image from Server in each region on your PC. (fil (filename: sony_fwboot_2015_<Version>_<Dest_ID(lower‐case)>_.zip, Refer the matrix of this page) 2015 V ID(l i R f f hi Extract TV firmware image and you will get 2files. (sony_fw_2015_<Version>_<Dest_ID>.pkg & sony_boot_2015_<Version>_<Dest_ID>.bin) Copy sony_fw_2015_<Version>_<Dest_ID>.pkg file to the root directory of USB pen drive. (ex: sony_fw_2015_1500_SLPDA.pkg) Insert USB pen drive to USB port of TV Insert USB pen drive to USB port of TV.
Page 156
2019/05/27 19:43:09 (GMT+09:00) How to update TV Software (2) After 20‐30 seconds, the LED is turn to Amber and blink. LED blinking indicates “Under SW Update”. IMPORTANT NOTE: PLEASE DO NOT PULL OUT THE AC PLUG DURING THIS STATE. After 1‐2 minutes, LED blinking will finish. Please press <Power> key. If “SONY” Logo displays the screen and LED is turn to GREEN, Software update is success!! success!! Pull out the USB pen drive from TV. SYS SET...
Page 157
2019/05/27 19:43:09 (GMT+09:00) How to update TV Software (3) 10. TV on standby and Enter Service Mode. Press “i+ (info)”, “5”, “Volume +” then “TV power” on remote. 11 Select “Status Information” item and Press <Enter> key 11. Select Status Information item and Press <Enter> key. 12. Confirm SW,NVM,Boot,Panel ID,PQ,AQ Version. 13. Press <Return> to back Service Mode Menu. 14 Select “UART Selection” by ↑↓ key and select “No log” item by ←→ Key 14.
Page 158
2019/05/27 19:43:09 (GMT+09:00) SECTION 4 Supp-1 SERVICE ADJUSTMENTS (Refer to Service Manual for details on other adjustment) After the TV turns ON, the indication ‘Hotel Mode Setting in process” 4-8. Hotel Mode Adjustment appears shortly on the top of the screen during input source change. 4-8-1.
Page 159
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 4-8-2 : Hotel Mode Settings Menu Tree 4 8 2 : Hotel Mode Settings Menu Tree Display Description i ti Options string Press on the Remote for adjustments 5. Hotel This will turn the Hotel and press to confirm.
Page 160
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 4-8-2 : Hotel Mode Settings Menu Tree 4 8 2 : Hotel Mode Settings Menu Tree Define which input Signal Source Setting: Use /Not Use source should be Digital available during Hotel Signal Source Setting: Use /Not Use Mode.
Page 161
BathSP Initial Set the initial TV Volume BathSP volume each 0-50 time a hotel customer turns the TV on. SI Mode Sony Standard Select the SI Mode Selection Selection of TV. Locatel No Serial =Default Settings SYS SET...
Page 162
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 4-8-3 : Smart Cloning Functions (1) 4 8 3 : Smart Cloning Functions (1) ( I ) Exporting functions ( II ) Importing functions Before you export your Hotel TV settings, NOTE Make sure that all the settings including channel, picture, sound and Hotel Menu are correct.
Page 163
2019/05/27 19:43:09 (GMT+09:00) Service Adjustment 4-8-4 : Entering Hotel Menu Mode (Hotel mode to Hotel Setting mode) 4-8-4 : Entering Hotel Menu Mode (Hotel mode to Hotel Setting mode) Do the following steps ONLY when it is Hotel mode Additional Information 4-8-6 : Hotel Mode (Guest Usage) 1.
Page 164
2019/05/27 19:43:09 (GMT+09:00) Diagrams SECTION 5 Supp-1 DIAGRAMS 5-1 CIRCUIT BOARD LOCATION 5-1.CIRCUIT BOARD LOCATION 5-1-1. 32” BA BOARD (ASIA) MOUNT BE BOARD (EUROPE) ( Asia ) SWITCH UNIT MOUNT 5-1-2. 40” HTL5 BOARD (FOR HOTEL MODEL ONLY) BE BOARD (EUROPE) SWITCH UNIT HKK BOARD HKK BOARD...
Need help?
Do you have a question about the KLV-32R4 C Series and is the answer not in the manual?
Questions and answers