Subscribe to Our Youtube Channel
Related Manuals for Harper DEBRIS 2700
Summary of Contents for Harper DEBRIS 2700
- Page 1 DEBRIS BLOWER 2700 Serial Number: 18A01 + Part # 301021 OPERATOR’S MANUAL Debris Blower 1-2024...
- Page 2 Debris Blower...
-
Page 3: Operator Section To The Owner Or Operator
MEANING: Failure to understand and obey this warning may result in injury to you or others. Whenever this symbol is used, please pay very close attention to the information presented, and make sure you fully understand. If you do not, contact your dealer or Harper Industries, Inc. for clarification. -
Page 4: Warranty Statement
The obligation of HII under this warranty is expressly limited, at our option, to replacement or repair at a service facility designated by Harper Industries or at the manufacturing plant in Harper, KS. A part will be replaced after inspection discloses it to have been defective. This... -
Page 5: Table Of Contents
Table of Contents OPERATOR SECTION To the Owner or Operator..........Warranty Statement............Table of Contents............Specifications..............Safety Information Equipment & Control........Guards & Shields..........Safety Decals........... Before Operation..........Operation............Control Identification PTO Shaft............3-Point Hitch Pins..........Input Shaft............Diverter Handle Assy........Belt Tensioner........... -
Page 6: Specifications
20-30 hp at PTO Superior Construction in every model: Every Harper Debris Blower has a durable polyester baked paint finish, with epoxy primer applied to cover completely and keep moisture out. This finish is extremely strong, and resists chipping and cracking. -
Page 7: Safety Information
Use genuine factory parts or parts with • New decals may be obtained from equivalent characteristics, including your local Harper Dealer. type, strength and material. Failure to do so may result in product malfunc- SAFETY WARNING! tion and possible injury to the operator •... -
Page 8: Operation
• Never allow hands, clothing or any • Keep your face and all body parts part of the body to enter the discharge away from inlet and discharge chute or near moving parts. openings. • Avoid wearing loose-fitting clothing. • Stay away from the discharge area when machine is in operation. -
Page 9: Control Identification
Control Identification Diverter Handle Assembly Impeller Shaft 3 PT. Hitch PTO Shaft Pins Input Shaft Caster Wheels PTO Shaft – Transfers power from the tractor to the Debris Blower. Make Belt Tensioner – Spring loaded and sure up or down angle of PTO shaft keeps the belts within proper tension does not exceed 15 degrees. -
Page 10: Assembly
Assembly Operation Remove from crate. SAFETY WARNING! Mount Diverter Handle Assembly to • Wear approved eye and ear protection while operating the the frame of the machine with the two Debris Blower. 3/8” bolts already in the frame. • Keep all guards in place during Connect PTO shaft to input shaft of machine, tighten set screws on shaft. -
Page 11: To Begin Operation
To begin operation: • Operating with the incorrect PTO Mount Debris Blower to 3-point of trac- length or angle may cause harm or damage to the tractor or debris tor and connect PTO shaft to tractor blower. output shaft. - Ensure that the PTO shaft is the correct length and angle. -
Page 12: Adjustments
Adjustments Service & Maintenance Belt Tension Adjustment SAFETY WARNING! • Check the condition of drive belts be- fore each use or after every 25 hours • Before servicing or inspecting the Debris Blower, make sure the power of operation. source is shut off and all moving parts have stopped. -
Page 13: Troubleshooting
Troubleshooting Belts: Problem: What to Check: Belts Slip • Tension adjustment • Load may be excessive • Bearings may have seized. Problem: What to Check: Belts wear rapidly, jump, • Pulleys may not be properly aligned catch, or twist. • Check with straightedge across face of pulleys Standard Torque Chart Size... - Page 14 Debris Blower...
-
Page 15: Parts Section
Debris Blower Parts Section Parts Section Operator’s Manual DB2700 DB3600 Debris Blower 2/2012... - Page 16 Debris Blower...
-
Page 17: Components
Table of Contents PARTS SECTION DB2700 Components............. Lower Assembly..........Discharge Assembly......... Caster Assembly..........Hitch Assembly..........Diverter Handle Assembly........ Upper Fan Cover Assembly......Shield w/ Decals..........Discharge Decal Assembly....... Decal Installation..........1.10 Debris Blower... - Page 18 Debris Blower...
- Page 19 Debris Blower...
- Page 20 Debris Blower...
- Page 21 Debris Blower ii 1.2...
- Page 22 Debris Blower iii 1.2...
- Page 23 Debris Blower iv 1.2...
- Page 24 Debris Blower...
- Page 25 Debris Blower...
- Page 26 Debris Blower...
- Page 27 Debris Blower...
- Page 28 Debris Blower...
- Page 29 Debris Blower...
- Page 30 Debris Blower...
- Page 31 Debris Blower 1.10...
- Page 32 NOTES Harper Industries, Inc. Telephone: 620-896-7381 151 E. Highway 160 Toll-Free: 800-835-1042 Harper, KS 67058 Fax: 620-896-7129 Website: www.harperindustries.com E-mail: info@harperindustries.com Debris Blower...
Need help?
Do you have a question about the DEBRIS 2700 and is the answer not in the manual?
Questions and answers