Table of Contents
Advertisement
Injinite
4096
Hybrid
Key Telephone
System
CUSTOMER
DATA
BASE PROGVG
Using the Remote Admin
Key Definitions
follow
the same steps and procedures
to program
the
4096 when using a texminal
(as outlined
in the
following
sections) *
700.3
PROGlUM
MODE ENTRY Cgey Sta-
tion)
pn>grammir~
is performed
at station
100 using
either
the
Enhanced
or Executive
Key Tele-
phone.
Programming
is always
done at this
station
regardless
of the class of service
or
which
station
has been assigned
the atten-
dant(s).
Before
entering
the program
mode,
the pro-
grammer
must
first verify that
the Key Tele-
phone is properly
connected
to station
100. To
enter the program
mode:
a Press ON/OFF
button
(LED lights and in-
tercom
dial tone is heard).
b. On the
dial
pad,
press
the aster&k
[*]
twice.
c. On the dial pad, enter the digits [21(3][6][6]
(ADMN).
Confirmation
tone is heard
and
cUa.l tone is removed.
d. The ON/OFF
button
LED is lit. The System
fs ready
to program.
(Other
telephones
connected
to the system continue
to func-
Uon normally.)
NOTE: I-
here if necessary. Refer to Set-
tion 600 and 700.4)
e.
f.
!3
h.
i.
Press the FLASH button.
Dial the two-digit
program
code for the
desired
data fleld.
Enter customer
data.
To permanently
store the entered
data
press
the HOLD
button.
A burst
of one
second confirmation
tone should be heard.
If an interrupted
(error) tone is heard,
re-
enter the data starting
with step E.
Repeat from step e. until all data has been
entered
into memory.
700.4
INITIALIZATION
The
system
has been pre-programmed
with
.
certain
features
which
are called default
data
(Refer
to Table
700-l).
These
features
are
loaded into memory
when the system is initial-
ized.
NOTE:
The
system
should
be initialized
when
installed
or at any time the data
base
has
been corrupted.
(Refer to
Section
700
for
complete
system
initialization
proce-
dures)
To return
the entire system database
to default
values:
Set switches
1 and 8 on the CPB to ON to
initialize
upon system power-up.
After initiali-
zation. switch 8 should be turned
to the 'OFF"
position.
(Refer to Section
700 for complete
initialization
i.nstrucUons)
Use the procedures
explained
below to return
only parts of the data base to default
values:
a
b.
C.
d.
e.
Enter the progmmmtng
mode.
Press FLASH button.
Dial 1701 to default
system parameters.
Press HOLD button.
Repeat from step B for the other areas. In
step C. use the following
program
codes:
-
1701 for system parameters
(including
d group
pwrammlng)
-
I711 for CO lines
-
[72] for station
parameters
-
1731 for exception
tables
-
(741 for system speed numbers
-
[75] for Least Cost Routtng
Tables
NC?272 Program Codes 70-75 DOES NOT tnitfal-
ize the database,
but returns all programmable
ciatatousdefaullzuiue.
700.5
CUSTOMER
DATA WORKSHEETS
Before any attempt
at programming
is made, it
is strongly
recommended
that
customer
data
worksheets
be prepared
(Refer to Appendix
A).
These worksheets
should
become
part
of the
permanent
record
of customer
programming.
Refer to the following
sections
when preparing
the worksheets.
700.6
DATA EASE FIELDS
The data fields are used to set system timers.
determine
central
offlce line features
and Key
Telephone
features.
When
entering
CO line
data and station
data, be sure to enter the exact
number
of digits specified.
The data fields and
features
are further
described
in the following
secuons.
Issue
1, January
1992
700-7
Advertisement
Table of Contents
