Trouble Shooting Ou - Pioneer DV-45A Service Manual
Hide thumbs
Also See for DV-45A:
- Operating instructions manual (80 pages) ,
- Specifications (1 page) ,
- Service manual (129 pages)
Table of Contents
Advertisement
5
=
6
_
7
=
8
7.1.8 TROUBLE SHOOTING
STARE
Power ON
¢ Tact-switches are damaged. (incase of only a key NG)
FLKY 1C101-pin 22 is it around +1.2V when you pushed
a POWER
key?
¢ Wireless remote controller receiver or iR signal line or SEL IR signal line is damaged.
(incase of only a key of wireless remote controller NG)
Does FLKB IC101-pin 17 (SEL IR) and IR and SEL IR signal lines change OV-3.3V
when you pushed a wireless remote controller key?
¢ Blow out fuse of the primary side
¢ As for P-CONT of POWER
SUPPLY
Unit is around 3.3V. Blow out micro-fuse on the
POWER
SUPPLY
Unit. (Check the each voltage.)
P101-P102 or POWER
SUPPLY
Unit is damaged.
¢ FL controller IC (IC101)
or RESET IC (IC 102) on the FLKY Assy is damaged.
Are IC101-pin 12 (XRESET)
and pin 11 (POWER ON) "H" level together?
Turn on the power again
after 2 - 3 minutes.
¢ Check the following connections :
POWER
SUPPLY
Unit - DVDM
Assy
DVDM Assy - JACB Assy
DVDM Assy - FLKY Assy
¢ Check each voltage regulators of DVDM
Assy :
1C¢791-pin 1 (+1.8V), 1C404-pin 4 (+3.3V), 1C402-pin 1 (+5V), 1C403 (+2.5V)
© Check each voltage (EV+6V, EV+4V, SW+3.3V, +12V, -28V, FLDC+ and FLDC-)
(If above voltage are not supplied, check the micro-fuse
P101-P 104.)
Are not there short and open-circuit between output connector of POWER
SUPPLY
Unit and CN401
of DVDM Assy?
¢ R103 of POWER
SUPPLY
Unit is damaged. No -28V voltage appear.
Yes
¢ Short or open the zenner diode on the POWER
SUPPLY Unit. (D302)
¢ Check the address bus and data bus of signal
interface between FR CPU (IC601)—AV1
(IC751),
Eby-Chip (1C701) and Servo DSP (IC201).
¢ Check each voltage regulators of DVDM Assy :
10-404 (+3.3V) and IC403 (+2.5V)
No
Is the indication
etFL normal?
FL indication is dark or flickers.
Yes
Clock generator IC481 or crystal resonator X481 is damaged.
Check waveform of each pin whether IC481 does oscillation.
Indicates the error message
Refer to the section "7.1.6 ERROR DISPLAY". | .
¢ Blow out micro-fuse on the POWER
SUPPLY
Unit.
(P101 and P102)
¢ Check the following connections :
DVDM Assy (CN103)- LOAB Assy (5P connector assy)
DVDM Assy CN105-pin 12 (INSIDE SW signal)
¢ Check the loading drive signal : 1C351-pin 14, 15, 16
° Check the +6V and +12V power supply voltage
(If above voltage is not supplied, check the micro-fuse P101 and P102.)
Is tray open ?
Yes
77
Advertisement
Table of Contents
