The use of a substitute replacement component which does Leakage 0.5mA current Device not have the same safety characteristics as the PIONEER tester under recommended replacement one, shown in the parts list in test this Service Manual, may create shock, fire, or other hazards.
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DV-490V-S...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING SECTION POLYBAG,INSTRUCTION (RED CAUTION) GUARANTEE CARD "Operating Instructions" POLY BAG INSTA5 TRANSMITTER CORD,RCA PIN BATTERY,MANGAN PACKAGE PACKAGE GIFT SHEET PACKAGE PACKAGE PACKAGE,PAD DV-490V-S...
Page 7
Battery,Mangan (AR, R6P) • • • • NSP 6 Guarantee Card J2D30902A Instruction Book J2I80101B ( English ) Instruction Book J2I80110B ( French ) Package.Pad 792WHA0604 Polyethylene Bag,Instruction JB5UD300 Gift Sheet 791WHA0100 Package 792WHAA190 Gift Box 793WCDD172 Poly. Bag 791WHAA040 DV-490V-S...
CD2301 NOTE: Applying positions AA, AB and AC for the CLASS PART NO. MARK PART NAME grease are displayed for this section. GREASE GEM1018 G-555G Check if the correct grease is applied for each GYA1001 G-313Y position. GEM1036 FL-78A DV-490V-S...
3.5 DVD MT PCB ASSY(2/7) DVD MT PCB ASSY (A2I901A130) MEMORY BLOCK DV-490V-S...
Page 21
16Mbit FLASH IC S29AL016D70TFI020 PCB130 DMF073 NOTE :THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE : THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-490V-S...
: VIDEO SIGNAL ROUTE (R/CR ch) (G/Y) : VIDEO SIGNAL ROUTE (G/Y ch) (B/CB) : VIDEO SIGNAL ROUTE (B/CB ch) : AUDIO DATA SIGNAL ROUTE (DA) W888 : AUDIO SIGNAL ROUTE (Digital) : AUDIO SIGNAL ROUTE (L ch) D_GND DV-490V-S...
Page 27
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CAUTION: DIGITAL TRANSISTOR TP7301 S_C_OUT (SC) S_Y_OUT (SY) CVBS_OUT W878 TP7304 (R/CR) PCB130 DMF073 CVBS/Y/U/V S+COAXIAL J7302 J7301 RCA-405A-08 R102-D04KA(III)-06 DV-490V-S...
FROM/TO POWER CP4003 (CP502) A2001WV2-14P P.CON+12V AT+12V for MUTE P.CON+5V P.CON+6V GND(M) AT+3.3V +3.3V TP4031 AT+3.3V STBY L GND(D) FL DC- FL DC+ -28V NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-490V-S...
Page 31
V+3E V+1R8 (CORE) V+1R8 V+3A C4105 ADAC_GND R4058 100P CH PWDN# FLDC- FLDC+ -28V D_GND FRROM/TO MEMORY D_GND PCB130 DMF073 NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-490V-S...
DEF086 FFC(1.0mm pitch) CD602 2H091303 CP603 CP602 (CP602) (CP603) 00_6232_009_102_800+ 00_6232_009_102_800+ Vout STOP STOP PLAY/+SKIP PLAY/+SKIP PAUSE/-SKIP PAUSE/-SKIP OS651 V+3E V+3E C668 POWER POWER ROM-N340TAO 0.01 B W804 OPERATION 2 PCB ASSY PCB280 (A2I802A280) DEF085 B C G H DV-490V-S...
Page 33
-28V FLDC- FLDC- PCB270 DEF084 NOTE : THE DC VOLTAGE EACH PART WAS MEASURED NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-490V-S...
ATTENTION: ATTENTION: LES PIECES REPAREES PAR UN ETANT POUR UNE PROTECTION CONTINUE LES RISQUES D'INCEIE N'UTILISER QUE DES FUSIBLE DE MEME TYPE DANGEREUSES AN POINT DE VUE SECURITE 1.6A 125V{F501} N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DV-490V-S...
Page 35
THE DC VOLTAGE EACH PART WAS NOTE : THE RESISTOR MARKED F IS FUSE RESISTOR. THE TIME OF PRINTING AND SUBJECT TO CHANGE MEASURED WITH THE DIGITAL TESTER THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP WITHOUT NOTICE DURING PLAYBACK. IS NON POLAR ONE. DV-490V-S...
Page 37
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram J7301-pin 4 ( C ) OPERATION PCB ASSY µs 500mV IC651 -pin 5 (OSC) µs 500mV DV-490V-S...
Resistor array 3-terminal regulator LOADING MOTOR LOADING MOTOR PCB ASSY PCB ASSY (INSERTED PARTS) (CHIP MOUNTED PARTS) SIDE A SIDE B CD2302 CP2302 M2603 M2603 SW PCB ASSY LOADING MOTOR CD2301 M2602 SLED MOTOR CD2301 M2601 SPINDLE MOTOR CP2303 DV-490V-S...
There is no Service Parts J7301 RCA JACK 063Y000081 J7302 RCA JACK 060R451010 J8003 RCA JACK 060R451009 CP5901 CONNECTOR 0694YJ3018 X4001 CRYSTAL (27MHz) 100GT02720 OPERATION PCB ASSY SEMICONDUCTORS IC651 IC PT6315 IF4K063150 SWITCHES AND RELAYS SW652 - SW659 SWITCH TACT 0504R01T38 DV-490V-S...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the Flux smoke from it. Short circuit using a soldering iron. Pick Up PCB Fig. 1 DV-490V-S...
• After going into test mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the test mode. • The SKIP key and the SCAN key are effective during the test mode. TEST MODE: OFF POWER GGF1381 Test mode remote control unit DV-490V-S...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-490V-S...
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. DV-490V-S...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-490V-S...
• Region confirmation mode (ESC + A.MON [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-490V-S...
Character in bold : Item name : Information display 1 Destination indication Display it according to model information set from the FL Driver IC. 2 Region No. 3 ROM number 4 REG CHK 5 SUM CHK 6 CHIP VERSION DV-490V-S...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-490V-S...
Measure the voltage between the two ends of R2320 or R2322 on the DVDM Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. To OPTICAL PICKU DVD MT PCB ASSY CP2301 Front side SIDE A DV-490V-S...
DVD MT PCB Assy Check the video signal path between DVD IC (DVD MT Assy IC4001) displayed on the monitor Video circuit after DVD IC and video-out terminal (see the block diagram) (The FL display lights. The (IC4001) mechanism does not work.) DV-490V-S...
Page 61
Is there a problem with the format of the disc ? (block noise, freeze, other) No sound Is signal output from IC4001-pin184 and pin 186 on the DVD MT Assy (Picture is normal) DVD MT PCB Assy DVD IC (IC4001) DV-490V-S...
Page 62
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT Assy : IC4001) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT Assy : IC4005) Block noise is generated during playback. DV-490V-S...
Up PCB and DVD PCB connector. 1-4: DVD PCB (Refer to Fig. 1-4) Power PCB Remove the 5 screws 1. Remove the 4 screws 2. Remove the DVD PCB in the direction of arrow. DVD PCB Fig. 1-2 Fig. 1-4 DV-490V-S...
Page 65
3 supports 1. between A and B. Fig. 2-3-D Remove the Plate Clamper, Magnet Clamper and Clamper. Check Hook Check Hook Plate Clamper Magnet Clamper Main Frame Loading Motor PCB Ass’y Clamper Check Hook Fig. 2-5-A Fig. 2-3-E DV-490V-S...
Page 66
Remove the Switch PCB Ass'y. 8.0 ± 0.2 mm Remove the screw 4. Remove the Gear Feed. Feed Motor Remove the 2 screws 5. Remove the Feed Motor. Remove the Gear Motor. Safety surface for pressing of the insert. Fig. 2-7-C DV-490V-S...
Page 67
When installing the FFC, fold it correctly and install it as shown from Fig. 2-8. NOTE Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Printing _Serface 79 ± 1 mm Reinforcement Plat To Pick Up PCB Fig. 2-8 DV-490V-S...
Page 69
TV Encoder Module Videop RF Amplifier Video DAC Servo IO Servo Motor Processor Video Drive Processor interlacer Spindle Control FLASH MPEG-1/2 Audio JPEG Memory Video Decoder Controller DRAM System Audio Parser Audio Output CPPM/CPRM SPDIF System GPIO 32-bit RISC IR/VFD DV-490V-S...
Page 70
MT1389FE/E-L (DVD MT PCB ASSY : IC4001) • MPEG/MICON/DSP CPU • Pin Function DV-490V-S...
Page 79
Note: 1. The Main column is the main function, Alt. means alternative function. 2. The external TV encoder mode only supports CCIR-656 mode. DV-490V-S...
MP3 and The DVD side of a DualDisc plays in this WMA files – do not use for other file types) product. Formore detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer. DV-490V-S...
Group 4: Hebrew (iw), Yiddish (ji) detailed information. Group 5: Turkish (tr) Discs recorded in packet write mode (UDF format) are not compatible with this player. Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information. DV-490V-S...
8 Display Compatible Description of the display. This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode. 16 HDMI indicator Lights when this player is recognized by another HDMl or DVI/HDCP compatible component. DV-490V-S...
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). Press to jump to the beginning of the current DV-490V-S...
Page 84
Use to select menu options, etc. playing. 24 ZOOM 18 MENU Press to change the zoom level. Press to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-490V-S...
Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Refer to " 2.3 06 DVD MECHA SECTION " and Cleaning paper : GED-008 Refer to " 7.3 DVD DECK SECTION " DV-490V-S...
Need help?
Do you have a question about the DV-490V-S and is the answer not in the manual?
Questions and answers