Advertisement
Quick Links
Advertisement
Related Manuals for E-LOK 705
Summary of Contents for E-LOK 705
- Page 1 705/707 & 715/717 User Manual...
-
Page 2: Summary Check List
7 - S e r i e s Summary Check List: 1. Crop out done as per template. 2. Arrow on spindle hub points to lever/hinges. 3. Check rubber gasket installed correctly, with lugs pressed in tight, to ensure seal around backplate edge. - Page 3 7 - S e r i e s Please Note: Keep the included mechanical keys in a convenient place such as an Elements Hardware 1236-BLK Key Safe Replace the batteries when they have low voltage Read this User Manual carefully before installing your 7- Series Smart Lock Use 1.5v Alkaline Batteries 1236-BLK Shown:...
-
Page 4: Contents Page
Pg 28. Unlock with Mechanical Key Pg 29. E-LOK Gateway Pg. 1 Pg 30. E-LOK Gateway Pg. 2 Pg 31. E-LOK Gateway Pg. 3 Pg 32. E-LOK Gateway Reset, Transfer Ownership & Specs Pg 33. Maintenance Guide Pg 34. Important Notes Pg 35. Contact... - Page 5 7 - S e r i e s 7-Series Body Dimensions: 705 & 707 model shown on left with Standard Lever, rear panel 715 & 717 model shown in mid-left with Snib Lever, front panel Mounting points shown mid-right Body and lever projection shown on right...
- Page 6 7 - S e r i e s Common Mortice Lock Options: All Mortice templates are available online at E-LOK.com Back set: 35mm Sliding door lock 30mm 35mm 45mm 52mm 47mm Case Width: Back set: 40mm 60mm 45mm 57mm 62mm...
- Page 7 7 - S e r i e s 7-Series Packing List: (not included with 705-0, 707-0, 715-0 & 717-0) Front Panel Back Panel User Manual Mortice lock QTY 1 QTY 1 QTY 1 QTY 1 Faceplate & Mechanical Key RFID Card...
-
Page 8: Specifications
Available Mortice lock Sizes: 30, 35, 40, 45, 50, 55, 60, 70mm Back Set & 28,35mm Sliding Lock 7-Series Residential Warranty: 2 Year Mechanical & Electrical E-LOK Gateway Warranty: 2 Year Weather Rating: Exterior Rated IP 55 (705 and 715 Models Only) - Page 9 7 - S e r i e s Adjusting the Handing: Location of screw shown: To turn the handing on the front panel, loosen the inner screw. (new model E- LOKs come with hex screws, not Phillips). Remove the handle. After adjusting the direction of the handle, insert it into the handle seat, re- tighten the inner screw and ensure arrow is pointing in the direction of the handle (above image).
- Page 10 If you are experiencing these symptoms please ensure the arrow alignment is correct + split pin is installed. If your E-LOK was working fine for 4-12 weeks and now won't open from the outside, the Split Pin may have not been installed.
-
Page 11: Installation
If you are fitting the 7-Series into a new hole, take the included mortice template and cut the holes into your door. Your E-LOK 7- Series comes with screws to suit both wooden and aluminium doors. - Page 12 Screw the back panel to front. Depending on your door width, use the appropriate included fixings screws for the top and bottom fixing points. Install Batteries into battery case and screw the battery cover back into place. E-LOK 7-Series Smart Lock should be ready to go!
- Page 13 You must be admin and in Bluetooth range of the Smart Lock in order to complete factory reset. You can factory reset your E-LOK by going into the lock settings and tapping "Delete". This will fully factory reset the E-LOK Smart Lock.
- Page 14 E-LOK App. Please Note: The default code before connecting to the E-LOK, is 123456#. Trouble shooting: If you manual reset whilst you were admin of the E-LOK, transferring Lockset to Trash will complete the reset of the E-LOK:...
-
Page 15: First Setup
7 - S e r i e s First Set-Up: Get the E-LOK App by visiting E-LOK.com for the app download link 1. Register an account 2. Login to your account. 3. Ensure E-LOK 7-Series with E-LOK using either is on and Bluetooth phone number or email. - Page 16 PIN code Management: E-LOK App allows you to set 200 unique PIN Codes. You can set a range of different types of PIN Code. The best is to choose 'Custom' to create yours. Set it to permanent, name it and set your preferred sequence. (4-9 digits).
- Page 17 RFID Card + Vague Code + Fingerprint Management RFID Card Management: E-LOK App allows you to store 200 unique RFID Cards. To set up one of the three included with your E-LOK 7-Series Smart Lock, tap "Cards" on the lock management page, tap Add Card.
- Page 18 Remotely is enabled in the settings. Now tap the Unlock icon. This will unlock your E-LOK via Wi-Fi. If Auto Lock is on in the E-LOK settings, it will lock automatically. Otherwise you can hold down the lock button to lock it remotely...
- Page 19 7 - S e r i e s Admin Passcode + Unlock Records Admin Passcode: E-LOK comes with an admin passcode. To view this tap "Settings" on the lock management page, tap "Basics" and then tap "Admin Passcode". Keep a note of this passcode.
- Page 20 Battery Percentage + Lockset Clock: Check Battery Percentage: E-LOK App allows you to check the battery percentage of your E-LOK in two easy ways. In the lock select page, the app will give you a percentage overview to the nearest 5%. You can also find a more accurate battery level in the settings of the Smart Lock.
-
Page 21: Passage Mode
Series Smart Lock. Tap into "Settings", "Passage Mode", then choose the days and hours you want your E-LOK Smart Lock to be in passage mode. A common application for this is having a Smart Lock on passage mode Mon-Fri 9am-5pm for an office building. - Page 22 Holding down the "#" key is a preferred option. E-LOK Remote: E-LOK’s have a function where you can connect a remote to the lock, so you can unlock and lock it via bluetooth. First, go to Remote, on the E-LOK management page. Next choose permanent, timed, or recurring.
- Page 23 Extra Smart Lock Settings: Auto Lock: E-LOK App allows you to adjust the auto lock timer on the Smart Lock. This is the timer that is triggered once the Smart Lock has been unlocked using any unlock method unless passage mode is enabled. Auto lock timer is under the lock settings tab.
- Page 24 Extra Smart Lock Settings: Reset Button: With E-LOK App, you can enable or disable the factory reset button inside the battery case. Disabling this reset button will prevent someone from resetting the E-LOK Smart Lock and locking you out (apart from mechanical key). This feature works great on E-LOK's installed on Airbnb's, rentals etc.
- Page 25 Extra Smart Lock Settings: Lock Groups: You can link E-LOK Smart Locks together in lock groups. First create a lock group in the main settings, then link a Smart Lock to the group in each individual lock settings, via Settings - Basics - Lock Group. View lock groups in the select page.
- Page 26 Transfer Lockset Ownership: Transferring Lockset ownership can be useful in a few scenarios. What it allows you to do is give Master Admin ownership to another E-LOK App account holder. The process to Transfer Lockset Ownership is shown below: Tap into "Settings" then into "Transfer Lock(s)". Here you can select the Smart Lock you wish to transfer ownership.
- Page 27 Important Notes: When the E-LOK 7-Series automatically locks, the handle disengages from the latch, but you can still lift the handle to engage the mortice bolt. Engaging the deadbolt when the E-LOK is not electronically locked (aka in passage mode), the E-LOK will not be locked, and you could then pull down on the handle to unlock it even with the deadbolt engaged.
- Page 28 Unlocking E-LOK 7-Series with Key Your E-LOK comes with two mechanical keys and a slot in the front panel to use them. If you've forgotten your PIN Code or your E-LOK 7- Series batteries are flat, follow these steps to unlock it mechanically.
- Page 29 If the E-LOK Gateway is not near one or both, connection may be poor and the E-LOK Gateway may not function as expected. To add the E-LOK Gateway to the E-LOK App follows these steps: Open the left menu on the E-LOK App. Tap "Gateway". Tap "+" Sign. Select "G2"...
- Page 30 7 - S e r i e s E-LOK Gateway (only if you've purchased the E-LOK Gateway Add-On) Plug in E-LOK Gateway. The light should flash red and blue - this means its ready to connect. Tap "Next" then Tap "G2"...
- Page 31 Series. Open your lock management, tap into "Settings", locate the "Unlock Remotely" menu and ensure this is enabled. You will now be able to control your E-LOK 7-Series from the app remotely via Wi-Fi, whether you're at work or out-of-town. You can add, change or delete unlock codes.
- Page 32 E-LOK Gateway Specs + other info Reset E-LOK Gateway: If you require factory reset your E-LOK Gateway follow the below process. Removing the Gateway from your app will unlink the Smart Locks that are connected to it. The Smart Locks will work as usual via Bluetooth.
- Page 33 Loctite securing the handle to either or both the front and rear panel. It is also a good idea to do a full factory reset of the E-LOK 7-Series Smart Lock to ensure software stays light and un-bloated.
-
Page 34: Important Notes
Important Notes: Please Note: You must use the E-LOK App to set-up your E-LOK 7-Series Smart Lock. When you first power up your E-LOK, the Smart Lock will have very limited features until you have completed the short set-up process and added at least one unlock code. - Page 35 7 - S e r i e s Contact: If you run into trouble with your E-LOK Smart Lock please visit: E- LOK.com for further information, help and tools. If you don't find your answer on E-LOK.com use the contact box and send us an email.
- Page 36 7 - S e r i e s Notes:...
- Page 37 7 - S e r i e s Notes:...
- Page 38 7 - S e r i e s User Manual E-LOK.com Version: 2312 E7UM...