Related Manuals for Delta PPM DC1 100
Summary of Contents for Delta PPM DC1 100
- Page 1 The power behind competitiveness Delta Data Collector PPM DC1_100 Installation Manual www.deltaww.com...
-
Page 2: Table Of Contents
Contents ■ Introduction ■ ........... . . ... -
Page 3: Precautions For Your Safety
Precautions for Your Safety ■ Notations for safe use of the product and their meanings This Instruction Manual provides precautions with the following notations and symbols for safe use of the PPM DC1_100. The expression “Product”, “Data Collector” or “DC1” refers to the PPM DC1_100. Precautions described herein contain important aspects of safety. -
Page 4: Essential Points For Safety
・ Pull 16-pin terminal and Power supply terminal off when any abnormality is detected like smoke, heat. ・ Install the product with the “DELTA” logo facing front when in stalling the Data Collector on a wall. ・ Take care to ensure no water or other liquid gets on the Data Collector. -
Page 5: Product Overview
Product Overview DC1 data collector is designed for monitoring PV inverter and conducting partial / zero export application to ensure solar power will feed in base on power company requirement. With its wired and wireless communication interface, DC1 can be connected to either MyDeltaSolar or 3rd party cloud service to realize remote management and optimize the efficiency of the PV system. -
Page 6: Preparation Before Construction
１.Preparation before construction 1.1.Scope of Delivery Verify that following items are available for use prior to using this feature. Product name Remarks Shape Data Collector 1 unit Main unit Wi-Fi Antenna 1 piece Install antenna to Enhance Wireless Signals. DIN Rail 1 piece This is a rail used to install the product on a wall. -
Page 7: Dimension
1.2.Dimension 55 mm 72 mm Din Rail 125±1 3.5±0.5 unit: mm... -
Page 8: Descriptions And Functions Of Parts And Components
1.3.Descriptions and Functions of Parts and Components ①MICRO SD POWER IN Use SD card to reset Data Collector to factory default. The settings and records will be deleted. ②Reset button Resetting the Data Collector. Restart the Data Collector. The settings and records will not be deleted. ③Wi-Fi antenna Install antenna to Enhance Wireless Signals. -
Page 9: Reset Method
1.4.Reset Method TOP VIEW Press reset button System ready led flashing Action of DC1 POWER IN 3~5 sec 0.5sec ON, 0.5sec OFF Rebuild wifi module Reset wifi password and 6~10 sec 1sec ON, 1sec OFF rebuild wifi module Reset DC1 setting without SN, Over 15sec 2sec ON, 2sec OFF then reboot... -
Page 10: Installation
* If the external box is made of metal, Wi-Fi antenna needs to be installed outside the box (F). User needs to use extension cable to connect the Wi-Fi antenna. （２） An external box is available for customer from Delta. Contact retailer for more details. -
Page 11: Connection To The Inverter
2.3.Connection to the inverter (1) Prepare 0.3 to 0.5mm² single wire, 4 cores (twin wires) shielded cables (rated temperature: 80ºC to 85ºC). * Process the cables before use. Φ 0.6~0.8 Φ 5~6 Cable 40mm Inverter 16pin connector RS-485 Power - GND 12/24 V Power - + CAT5 / CAT6... -
Page 12: Download The App
2.4.Download the APP DeltaSolar 1. This APP should collocate with Delta Inverter. 2. If inverter is not connected to cloud, you still can monitor inverter by APP. Where can search for DeltaSolar APP? - QR Code: Please scan the QR code to MyDeltaSolar cloud. -
Page 13: System Application
３.DC1 system application When 3rd party monitoring and delta cloud monitoring are using at same time, suggest to add below IP into network white list to make sure remote function and cloud monitoring work normal. Back end remote function IP : 52.187.179.41 / Cloud monitoring IP : 52.237.74.126 Suggest 3rd party monitoring system can enable VPN or Port forwarding function of the local router, so Delta service will able to remote debug when needed. -
Page 14: Retrofit Mode
Connection type Wired (RS-485) Wi-Fi Mixed Solivia G3 Solivia G4 RPI HxA HXA_2xx M6/8/10A M15/20A M30A M50A_12s M88H M15/20/30A_2xx M50/70A_2xx M100_210 M100A_280 M125HV Wired: max 32 inverters Wi-Fi: max 9 inverters Mixed: max 32 inverters ● Connection type DC1 - Router Ethernet or Wi-Fi ●... - Page 15 3.2.Retrofit mode This function is only for Solivia Gateway, the Wi-Fi inverter is set by DC1 through the APP. Start Solivia Gateway to monitor on Solivia Cloud. PV array ID 1 Solivia Solivia Cloud PV array ID 2 Solivia Gateway RPI M6/8/10A PV array ID 3...
-
Page 16: 3Rd Party Monitoring - Modbus Tcp/Ip
3.3. 3rd party monitoring - Modbus tcp/ip RS-485 or Wi-Fi inverter is set by DC1 through the APP. After the setting is completed, the third-party monitoring reads the communication address of DC1 through Modbus to get the power generation data. Power line RS-485 PV array... -
Page 17: 3Rd Party Monitoring - Modbus Rtu (Forward Mode)
3.4 3rd party monitoring - Modbus RTU (Forward mode) 3rd party monitoring device with Delta Modbus RTU protocol address built in can be used. DC1 is master of inverters, also the slave of 3rd party monitoring device. Power line RS-485... - Page 18 ATTENTION - When forward mode is enable, DC1 will not able to deliver monitoring data to cloud and APP. For details, please go to the following link for the APP operation manual. DeltaSolar APP Operation Manual: https://mydeltasolar.deltaww.com/index.php?p=manual...
-
Page 19: Specifications
４. Specifications ELECTRONIC SPEC PPM DC1_100 Operating voltage range 9Vdc ~ 25Vdc (power port, can be supplied from inverter) Max. Power Consumption 5 Watt COMMUNICATION Wired RS-485/ Ethernet Wireless Internal Wi-Fi Module 802.11a/b/g/n REGULATION Safety Standard EN 61010-1, CE compliance Emission (EMI) EN 300 328, LP0002, Part 15C, Telec T66, KC Immunity(EMS) -
Page 20: When Something Seems Wrong (Troubleshooting)
５. When Something Seems Wrong (Troubleshooting) 5.1.Error Displays When a problem occurs, confirm the Error message from the [ERROR EVENTS LOG] page of [History]. Details can be verified in the “ERROR EVENTS LOG” pages. Refer to the Manual of the Inverter for details on the error codes. -
Page 21: Troubleshooting
5.2.Troubleshooting Responsive actions that should be taken in cases where the following symptoms occur are described. Symptom Verification details Responsive action DC1 is booting Please wait two minutes for the boot to complete System ready light is red DC1 is Searching or Setting Please wait for 2-10 minutes for Inverter to search or inverters. -
Page 22: Appendix - Ppm P1_120
Appendix - PPM P1_120 1. Functions of Parts Reserved, no electrical connection allowed Mains voltage connector block CT wire connector Connect with Data Collector Meter status LED Reset Button RS-485 port & terminal resistor port 2. LED Description Status Explanation Hardware failure Blink No communication from other device... -
Page 23: Appendix - Ppm P3_120
Appendix - PPM P3_120 1. Functions of Parts Mains voltage connector block CT wire connector Connect with Data Collector Meter status LED Reset Button RS-485 port & terminal resistor port 2. LED Description Status Explanation Hardware failure Blink No communication from other device Green Normal Green... - Page 24 20230914...