Advertisement
z
0
u,
->.
--.J
0
~
~
12
•
•
I
I
I
HOW TO INITIALIZE
THE
SETTING
SCREEN DISPLAY AND SELECTIONS
IN THE
<SET-UP MENU> RESET MODE------
You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and
the volume level to their factory-set (initial) values.
1. Press the Power switch to set the unit to STAND
BY(I<!>)
mode.
...________11-
I
ON
~ I
c!)
STANO BY
2. While pressing both MENU button and PHASE ( r:A,)
button, press the Power switch to turn the power ON
( -1 ).
The <SET-UP MENU> RESET screen is displayed.
.., I V
*
The screen automatically disappears when no operation
In!
'cjl
o-
1 oN
is performed after about 5 minutes.
t;_;:)
t;;;.;;:J
Ic!)STANDBY
Fl-VISE
"'8,lJ
PowEA
(
Note: )
3. Setting
[ • Initialization is required.
!OJ
• The <SET-UP MENU> RESET screen will not be
displayed
if
the MENU or PHASE buttons are pressed
for a very short time. Keep pressing them until the
display screen appears.
Press the CONTRAST ( () ) button.
* Initialization is completed, and the <SET-UP MENU>
RESET screen disappears.
[ • Initialization is not required.
lt@ll
Press the VOLUME/SELECT[+]
or[-]
button.
*
Initialization is aborted, and the <SET-UP MENU>
RESET screen disappears.
<SET-UP MENU> RESET screen
<SET~UP MENU> RESET
Are you
sure?
"Yes"
then
<CONTRAST>
"No"
then
Initial settin_g_s
j
Functions (Items)
Initialization
(setting)
SHARPNESS
00
~
COLOR TEMP.
6500
~
COLOR SYSTEM
AUTO
~ ASPECT RATIO
4-3
dJ
RGB/COMPONENT RGB
~
COMPO. LEVEL
00
BLUE CHECK
OFF
H. POSITION
00
c:
V. POSITION
00
~
WHITE BALANCE
~
R. CUTOFF
00
A
G. CUTOFF
00
:::,
z
B. CUTOFF
00
w
"
R. DRIVE
00
CL
B. DRIVE
00
:::,
~
CONTROL LOCK
OFF
~
STATUS DISPLAY
ON
v
INPUT REMOTE
OFF
ASPECT REMOTE OFF
i
PHASE
00
~
CHROMA
00
~
CONTRAST
00
~ BRIGHT
00
t3
a:
1
VOLUME
20
g
•
•
•
i
i
BASIC CONNECTION
EXAMPLE
( Notes:)
• Before connecting your system, make sure that all units are turned off.
• The illustration below shows some examples of different connections. Terminal connections may differ depending on the
component connected. Be sure to refer to the instructions provided with the unit(s) you are connectmg.
• Each pair of mput (IN) and output (OUT) terminals are bridge-connected.
• If you're not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the bridged output (OUT)
terminal as this will cause the terminating resistance switch to open (auto terminate function).
• When making a bridge connection, connect the input {IN) and output (OUT) terminals on the monitor to separate video components.
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by the same video
signal "loopmg" between the VCRs, and is not a malfunction.)
• Select the video input (INPUT A (VIDEO), INPUT B (Y/C) or INPUT RGB/COMPO./SDI) with the INPUT SELECT buttons on fhe front panel.
• The ASPECT RATIO or INPUT A/B settings can be controlled via the REMOTE terminal by setting ASPECT REMOTE or INPUT REMOTE in the
<SET-UP MENU> screen to valid. (Refer to pages 10 and 11.)
• VIDEO A Connection Example (Select Input A (VIDEO))
~
Video-.
(V,decs,gnalcable)
Video Camera
Cl
Video Monitor
Audm
1=~1
(Aud1os,gn.alcable)
VCR
• VIDEO B (VIDEO) Connection
Example (Select Input B (VIDEO))
~
Video Camera
Video-.
{V>deos,gnalcable)
Video Mornlor
Audio-.
lo=~I
;ii~s0
(Audtos1gnalcable)
VCR
RCA pm
closedc1rcu1t(short)
External control
functions
External control switch
I
I
07onp:~~u1t
1Clo;:~~t•1
~---~--~--~,
--------------
REMOTE
......_
(Remote cable)
Video-.
Ill
,-v-,
l(Vldeos,gnalcable)
Video-.
(Video s,gnalcable)
Audio
-.
(Aud,o:;'!Jnalcable)
I ~®~
I
Audio
~
(Aud,os,gnalcable)
.41..
REMOTE
-.
: Signal Flow
VCR
CJ
Video Monitor
~=~
VCR
CJ
Video Monitor
External control switch
RCA pm
13
--l
~
->.
O"l
u,
0
en
0
C
Advertisement
