Advertisement
SPECIFICATIONS
Measured
in
accordancae
with
EIA
Standard
RS-490(IHF
A-202).
Measurements
referred
to
8 ohm
are
taken
with
the
Speaker
lmpedance
selector
set
at
8 ohms
(High).
Measurements
for
4 and
2 ohms
are
taken
with
lmpedance
selector
at
4
ohm
(Normal).
NAD
2100
POWER
AMPLIFIERS
STEREO
MODE
CONTINUOUS
AVERAGE
POWER
OUTPUT
INTO
8 OHMS
(Min.
RMS
power
per
channel,
20Hz-
20kHz,
both
channels
driven,
with
no
more
than
the
rated
distortion)
Rated
distortion
(THD,
20
Hz-20
kHz)
Clipping
power,
(maximum
continuous
power
per
channel)
THF
Dynamic
Headroom
at
8 ohms
IHF
Dynamic
Power
(maximum
8 ohms
short-term
power
per
channel)
4 ohms
2 ohms
Slew
factor
Slew
rate
Damping
factor(ref.
8 ohms.
50
Hz)
Input
impedance
Input
sensitivity
for
1 Watt
for
rated
power
Voltage
Gain
Frequency
Response,
LAB
Input
Infrasonic
Filter,
NORMAL
Input
Ultrasonic
Filter,
NORMAL
Input
Signal/Noise
Ratio.
A-weighted
THD(Total
Harmonic
Distortion,
20HzZz-20kHz,from
250mW
to
rated
output)
SMPTE
I.M.(Intermodulation
Distortion,
60Hz
+
7kHz,4:1,
from
250mW
to
rated
output)
IHF
I.M.
(CCIF
IM
Distortion,
19
+
20
kHz
at
rated
output)
BRIDGED
(MONOPHONIC)
MODE
:
CONTINUOUS
AVERAGE
POWER
OUTPUT
INTO
8 OHMS(Min.
RMS
power
per
channel,
20Hz-
20kHz,
channels
driven,
with
no
more
than
the
rated
distortion)
IHF
Dynamic
Headroom
at
8 ohms
IHF
Dynamic
Power
(maximum
short-term
power
per
channel)
8 ohms
4 ohms
50
W(17
dBW)
0.03%
70 W
+6
dB
200
W(23
dBW)
250
W(24
dBW)
330
W(25
daBW)
>50
35V/usec
100
R=20
kohm
C=600pf
120
mV
0.85V
23x(27
dB)
3 Hz
to
100kHz
+0,
-3
dB
-3
dB
at
10Hz,
12
dB/octave
-3
dB
at
60kHz,
12 dB/octave
100
dB
ref.
1W
117
dB
ref.
rated
power
<0.03%
<0.03%
<0.03%
150W(21.7
dBW)*
+6
dB
500
W(27
dBW)
660
W(28
dBW)
PHYSICAL
SPECIFICATIONS
Width
x Height
x Depth
Net
Weight
Shipping
Weight
Power
Consumption
43.5
x
10.8
x
38.1
cm.
17.1
x
4.25
x
15
in.
9.52
kg(21
lbs).
10.88
kg(25
libs).
50/60
Hz
at
110,120,
220,
or
240
VAC/220
VA.
specifications
or designs
at any time without
notice.
Advertisement
