Specifications - Hitachi SV 12V Handling Instructions Manual

English |
bits, cutters.
GENERAL OPERATIONAL PRECAUTIONS ` ` 15. Remove adjusting keys and wrenches. Form habit
1. Keep work area clean. Cluttered areas and benches of checking to see that keys and adjusting wrench-
invite injuries. es are removed from tool before turning it on. |
2. Consider work area environment. Don't expose 16. Avoid unintentional starting. Don't carry plugged-in
power tools to rain. Don't use power tools in damp tool with finger on switch. Be sure switch is off
or wet locations. Keep work area well lit. when plugging in. ` I
Don't use tool in presence of flammable liquids or 17. Outdoor use extension cords. When tool is used
gases. outdoors, use only extension cords intended for use
Power tools produce sparks during operation. outdoors and so marked. .
They also spark when switching ON/OFF. Never 18. Stay alert. Watch what you are doing. Use common
use power tools in dangerous sites containing sense. Do not operate tool when you are tired.
lacquer, paint, benzine, thinner, gasoline, gases, 19. Check damaged parts. Before further use of the
adhesive agents, and other materials which are tool, a guard or other part that is damaged should
combustible or explosive. be carefully checked to determine that it will
3. Guard against electric shock. Prevent body contact operate properly and perform its intended function.
with grounded surfaces. For example; pipes, radia- Check for alignment of moving parts, binding of
tors, ranges, refrigerator enclosures.
moving parts, breakage of parts, mounting, and any
4. Keep children away. Do not let visitors contact tool other conditions that may affect its operation. A
or extension cord. All visitors should be kept away guard or other part that is damaged should be
from work area. properly repaired or replaced by an authorized
5. Store idle tools. When not in use, tools should be service center unless otherwise indicated else-
stored in dry and high or locked-up place-out of where in this instruction manual. Have defective
reach of children. switches replaced by authorized service center. Do
6. Don't force tool. It will do the job better and safer not use tool if switch does not turn it on and off.
at the rate for which it was intended. 20. Use the power tools only for applications specified
7. Use right tool. Don't force small tool or attachment in the Handling Instructions.
to do the job of a heavy-duty tool. Don't use tool for 21. To avoid personal injury, use only the accessories
purpose not intended -for example -don't use or attachment recommended in these handling
circular saw for cutting tree limbs or logs. instructions or in the HITACHI catalog.
8. Dress properly. Do not wear loose clothing or 22. Let only the authorized service facility do the
jewelry. They can be caught in moving parts. repairing. . .
Rubber gloves and non-skid footwear are recom- The manufacturer will not be responsible for any
mended when working outdoors. Wear protective damages or injuries caused by repair by unautho-
hair covering to contain long hair. rized persons or by mishandling of the tool. |
9. Use eye protection. Also use face or dust mask if 23. To ensure the designed operational integrity of
cutting operation is dusty. power tools, do not remove installed covers or
10. Don't abuse cord. Never carry tool by cord or yank screws. ;
it to disconnect from receptacle. Keep cord from 24. Do not touch movable parts or accessories unless
heat, oil and sharp edges. the power source has been disconnected.
11. Secure work. Use clamps or a vise to hold work. It's 25. Use your tool at lower input than specified on the
safer than using your hand and it frees both hands nameplate; otherwise, the finish may be spoited and
to operate tool. working efficiency reduced by motor overload.
12. Don't overreach. Keep proper footing and balance 26. Do not wipe plastic parts with solvent. Solvents
at all times. such as gasolíne, thinner, benzine, carbon tetra-
13. Maintain tools with care. Keep tools sharp and chloride, alcohol, ammonia and oil containing chlo-
clean for better and safer performance. Follow ric annex may damage and crack plastic parts. Do
instructions for lubricating and changing accesso- not wipe them with such solvent. Wipe plastic parts
ries. Inspect tool cords periodically and if damaged, with a soft cloth lightly dampened with soapy water.
have repaired by authorized service facility. Inspect 27. Use only original HITACHI replacement parts.
extension cords periodically and replace if dam- 28. Disassemble this tool only for replacement of
aged. Keep handles dry, clean, and free from oil and carbon brushes. |
grease. P y 29. Use the exploded assembly drawing on this han-
14. Disconnecttools. When not in use, before servicing, dling instructions only for authorized servicing.
and when changing accessories, such as blades,
SPECIFICATIONS
[Mode — | SVT SV125D SV125E
(110V, 115V, 120V, 127V, 220V, 230V, 240V) ^,
Input" 300W
No-Load Speed 4000 ~ 10000/min. 10000/min.
Diam. of Orbit
* Be sure to check the nameplate on product as it is subject to change by areas.