ZKTeco KR500-BT Quick Start Manual

QUICK START GUIDE
KR500-BT MOBILE
PROXIMITY READERS
This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made.
Models include KR500-BT
1.0 Introduction
A key component of a physical security electronic access control
system, a mobile-ready reader combining BLE and proximity
technologies is based on RFID technology. In operation it is capable of
reading data stored on a proximity credential via radio frequency—or
reading data from mobile credential stored in a smartphone's wallet
app via BLE technology—and without physical contact, and then
passing the data obtained to the physical access control system.
Access control systems typically manage and record the movement of
individuals through a protected area, such as a locked door.
2.0 Mounting Provisions
Each reader may be installed either indoors or outdoors. Mounting
options shown in the table below. Use supplied #6 mounting screws, or
equivalent security screws, for installation.
Model Mullion Mount
•
KR500-BT
*Plastic or metal
3.0 Reader Wiring
Wiegand
Conductor Function
Red DC (8-14 VDC)
Black Ground
Green Data 0
White Data 1
Brown Red LED
a
Orange Green LED
b
Yellow Card Present
Blue Beeper
Violet fleaPower
Drain Shield Ground
WIRING NOTES:
Single Line LED: This is the standard operating mode and does not make use of the
a
Orange conductor. The LED is Red when the reader is idle and flashes when a card is
presented. The LED turns Green when the Brown Conductor is pulled low by the access
control panel.
Dual Line LED: This mode makes use of both the Brown and Orange conductors. The
b
Brown conductor controls the Red LED and the Orange conductor controls the Green
LED. LED states are determined by the access control system option and capability.
Unused conductors should be trimmed, isolated and taped back to prevent unintended
current flows. Apply positive voltage only to the Red DC Conductor.
Single-Gang Wall Mount*
•
Magstripe
Conductor Function
Red DC (8-14 VDC)
Black Ground
Green Clock
White Data
Brown Red LED
Orange Green LED
Yellow Card Present
Blue Beeper
Violet fleaPower
Drain Shield Ground
4.0 Cable Requirements
24 AWG minimum, multi-conductor stranded with an overall foil shield,
for example Belden 9535 or similar, supporting the five conductors
comprising the physical layer of the Wiegand interface (power, ground,
data 0, data 1, and/or beeper and LED). Alternatively, Belden 9539 or
similar, for all reader functions. Contact your access control system
manufacturer for their specific requirements. Per the SIA's Wiegand
specification, maximum cable length is 500 feet (152 m).
5.0 Output Formats
• Wiegand (industry standard 26-bit Wiegand and
custom Wiegand formats)
• Magnetic Stripe (ABA Track II, clock and data,
with card present)
6.0 Grounding
Shield (drain) continuity must run from the reader to the access panel.
Shield (drain) and reader ground must be tied together at the access
panel and connect to an earth ground at one point.
7.0 Power
Reader may be powered by the access panel. A linear power supply is
recommended for best operation.
8.0 Voltage and Current
Voltage: 8 to 14 VDC
Current Draw: 60mA typical, 90mA peak
9.0 fleaPower™ Control Line
To reduce the average current required by the reader, pull the purple
conductor low.
10.0 Connection
Connection must be done in accordance with NFPA 70. Do not connect
to a receptacle controlled by a switch. Connect to a power limited DC
voltage source.
11.0 Troubleshooting
1. When the reader is first powered on it will beep 4-times, and the
LED will shine red.
2. Presenting a supported access credential will result in the reader
beeping and the LED flashing once.
3. Mobile operation is optimized for smartphones supporting BLE
(Bluetooth LE) version 4.2 or newer. Further, for the downloading
of mobile access credentials, a stable, high-quality internet
connection is recommended.