ZKTeco QR600 Series Quick Start Manual

ZKTeco QR600 Series Quick Start Manual

Qr code access control card reader

Advertisement

Quick Start Guide
QR Code Access Control Card Reader
(QR600 Series)
Version: 1.0
Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the
actual product and the written information in this manual.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QR600 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ZKTeco QR600 Series

  • Page 1 Quick Start Guide QR Code Access Control Card Reader (QR600 Series) Version: 1.0 Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
  • Page 2: Installation

    1 Installation Product size 1: (length 120 (±0.5) * width 80 (±0.5) * height 22.67 (±1)) (mm) screw hole is facing down Align the screw holes of the backplate with the holes drilled As shown in the figure above, Connec t the wires well, and on the wall, and fix the backplate remove the screw and remove i n s t a l l t h e d e v i c e o n t h e...
  • Page 3 Product size 2: (length 138 (±0.5) * width 58 (±0.5) * height 22.67 (±1)) (mm) screw hole is facing down Align the screw holes of the backplate with the holes drilled As shown in the figure above, Connec t the wires well, and on the wall, and fix the backplate remove the screw and remove i n s t a l l t h e d e v i c e o n t h e...
  • Page 4: Product Introduction

    2 Product Introduction The QR600 series QR code reader is a new generation of intelligent access control card reader developed by our company. The product has high-end appearance, high scanning speed, high recognition rate, strong compatibility, and can be connected to any access control controller that supports Wiegand input.
  • Page 5 Wiegand or 485 connection Connect the QR code reader to the controller via Wiegand or RS485 and then connect it the +12V power supply. The QR code reader does not need to be connected to the lock body when it is used as a reader. The controller in the figure only lists some of the wirings, and there are many kinds of connections between the machines.
  • Page 6: Device Operation

    Note: ① Support to connect the configuration tool through USB and serial port. ② USB: Connect to the configuration tool by means of USB communication; COM: Connect to the configuration tool by means of 485 communication. ③ The version number in the screenshot only represents the version number of the test sample, please refer to the version number of the actual product.
  • Page 7 Enter advanced settings page. On the "Reader Operation" page, set the configuration parameters of the card reader as required. ① Click "Search Device" to view the communication address of the card reader. Note: If you select the RS485 address, you can click "Search Device" to get the correct device address before you can perform other operations.
  • Page 8: Function Selection

    Click “Get Version” to view the version number information of the card reader. ② Set the relevant parameters of the card reader. ③ Description Parameter Read RTC Get the time of the card reader. Write RTC Set the time of the card reader. Set RTC Time Set to the current time of the PC.
  • Page 9 Description Parameter 0: Broadcast address, that is, the communication connection can be made regardless of whether the machine 485 address is set to 0~255. RS485 Address If the machine 485 address is set to 1~255, fill in the corresponding, you can also communicate.
  • Page 10 Description Parameter Wiegand Mode Wiegand 26, 34 and 66 are available. When Wiegand outputs the card number/information, the card number can be output Output Format in forward/reverse direction. Parity Check Whether to transmit the Wiegand check bit, output/non-output can be selected. Wiegand pulse width, optional (1~99) * 10us Pulse Width Wiegand pulse gap, optional (0~89) * 100+1000us.
  • Page 11 4.5 Reader Parameter Setting Operation Steps: On the "Read Card Setting" page, set the reading parameters of the card reader. Description Parameter Directory ID The ID of the directory file where the content of the user card to be read is located. File ID The file ID where the content of the user card to be read is located.
  • Page 12: Import And Export Configuration

    Once you have set the parameters, click "Write Con guration" to write the information to the card reader. Click "Read Con guration" to display the configuration information of the card reader. 4.6 Import and Export Configuration Operation Steps: On the “Page Con guration” page, click “Export Con guration” to exporting the page configuration information of the current device, click the “Import Con guration”...
  • Page 13: Firmware Upgrade

    4.7 Firmware Upgrade Operation Steps: On the "Firmware Upgrade" page, click "Open File", select the upgrade program, click "Start" button, plug in the USB and reconnect the computer to the computer to view the prompt message, indicating that the upgrade is successful.
  • Page 14 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com...

Table of Contents