Crestron MC2E 2-Series Compact Control System 2-Series Compact Control System with Ethernet: MC2E with Ethernet: MC2E Introduction Introduction Features and Functions 2-Series Engine At the heart of the MC2E is the powerful 32-bit Freescale ColdFire Crestron's exclusive enhanced real-time operating system makes the MC2E the fastest, most reliable control system available.
Page 6
Crestron’s IR wireless touchpanels or a third-party universal IR remote. 2 • 2-Series Compact Control System: MC2E ® ® ® touchpanel. ® Crestron MC2E ® computer or CE/PocketPC™ Operations Guide – DOC. 6142A...
Crestron MC2E Specifications Specifications for the MC2E are listed in the following table. MC2E Specifications (Continued on following page) Operations Guide – DOC. 6142A 2-Series Compact Control System SPECIFICATION Processor Memory SDRAM NVRAM Flash Operating System Ethernet Power Requirements Available Cresnet Power...
4 • 2-Series Compact Control System: MC2E SPECIFICATION Available Accessories PW-2420RU C2N-HBLOCK CNSP-XX IRP2 CNXRMIRD Crestron MC2E DETAILS 50 Watt Regulated Universal Power Supply Cresnet Network Distribution Block Custom Serial Interface Cable IR Probe IR Receiver Operations Guide – DOC. 6142A...
Page 9
Crestron MC2E MC2E Overall Dimensions Connectors, Controls & Indicators CONNECTORS CONTROLS & INDICATORS PWR LED NET LED RESET BUTTONS MSG LED LAN LEDs (Continued on following page) Operations Guide – DOC. 6142A 2-Series Compact Control System 19.00 in (48.26 cm) 17.03 in...
Page 10
RXD- and TXD- should idle low (going high at start of data transmission). If necessary, RXD+/RXD- and TXD+/TXD- may be swapped to maintain correct signal levels. Crestron MC2E DESCRIPTION DESCRIPTION (RXD-) RS-422 Receive Data (Idles low)
Page 11
Crestron MC2E Connectors, Controls & Indicators (Continued) CONNECTORS CONTROLS & INDICATORS COMPUTER COMPUTER Pin 1 Pin 9 GREEN YELLOW PIN 8 PIN 1 11, 12 11, 12, 13 24 VDC 24VDC 1.0A 1. Interface connectors for IR-SERIAL OUT, IR IN, I/O, RELAY OUT and NET ports are provided with the unit.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Crestron MC2E Operations Guide – DOC. 6142A...
Crestron MC2E Setup Network Wiring When wiring the network, consider the following: For more details, refer to “Check Network Wiring” on page 21. Identity Code Net ID The Net ID of the MC2E has been factory set to 02. This Net ID is defined as the “Master”...
2. Position a rack ear so that its mounting holes align with the holes vacated by the screws in step 1. 3. Secure the ear to the unit with three screws from step 1, as shown in the diagram on the following page. Crestron MC2E Operations Guide – DOC. 6142A...
Page 15
Crestron MC2E Bussing Strip Installation The 2-Series compact control system is supplied with two brass bussing strips to facilitate commoning (linking) of multiple terminal block connections. The bussing strips are constructed with four terminal block positions and may be trimmed to size for various applications or different devices.
- RELAY CLOSURES IR IN: FROM RELAY OUTPUT (1 - 4): CNXRMIRD TO CONTROLLABLE FOR RC-5 DEVICES CODE Crestron MC2E COM (A - B): LAN: 24VDC, 1.0A: TO ANY RS-232, 10/100 BASE-T AC POWER -422 OR -485 ETHERNET TO PACK...
Crestron MC2E Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com.
14 • 2-Series Compact Control System: MC2E • To incorporate the MC2E into the system, drag the MC2E from the Control Systems folder of the Device Library and drop it in the System Views. Crestron MC2E Operations Guide – DOC. 6142A...
Crestron MC2E Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication.
ID (specified on the MC2E’s IP table) and the internal gateway IP address 127.0.0.1. • Establish communication with the MC2E and display the “System Info” window. • Select Functions | Firmware… to upgrade the MC2E firmware. Crestron MC2E icon) and select the Operations Guide – DOC. 6142A...
Crestron MC2E Operation Crestron 2-Series Control Systems are the brain of a complete integrated audio/visual or automation solution, serving as the central processor and I/O interface. Every audio, video and environmental element of the home, boardroom, classroom or command center becomes integrated and accessible through the control system. No matter how complex or basic, Crestron control systems are entirely custom- programmable to attain the exact functionality required.
Various. Cresnet device Device not wired does not respond. correctly. Improper NET ID used. Crestron MC2E CORRECTIVE ACTION Use Crestron Toolbox to poll the network. Verify network connection to the device. If power is supplied through an AC adapter, verify the DC...
Page 23
Crestron MC2E MC2E Troubleshooting (Continued) NOTE: If communication cannot be established or the control system is locked-up, refer to “Troubleshooting Communications” in the Crestron 2-Series Control System Reference Guide (Doc. 6256). NOTE: Passthrough Mode enables Toolbox access to any serial controlled device on the network.
“File Transfer” window. 11. When file transfer is completed, you will see a window asking you to re-connect. Click Okay, then close the “Firmware” window and re-connect using the normal Address Book entry. Crestron MC2E Operations Guide – DOC. 6142A...
Crestron MC2E Check Network Wiring Use the Right Wire In order to ensure optimum performance over the full range of your installation topology, Crestron Certified Wire and only Crestron Certified Wire may be used. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire.
Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an “Addendum” in the Download column. 22 • 2-Series Compact Control System: MC2E DOCUMENT TITLE 2-Series Control Systems Reference Guide Crestron MC2E Operations Guide – DOC. 6142A...
Crestron MC2E Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes computer software and as applicable, associated media, printed materials and “online”...
Page 28
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, OR ANY OTHER WARRANTIES, NOR AUTHORIZES OTHER PARTY MERCHANTABILITY FOR THIS PRODUCT. THIS WARRANTY STATEMENT SUPERSEDES ALL PREVIOUS WARRANTIES. 24 • 2-Series Compact Control System: MC2E PROPRIETARY RIGHTS GOVERNING LAW CRESTRON LIMITED WARRANTY OFFER WARRANTIES, Crestron MC2E INCLUDING WARRANTIES Operations Guide – DOC. 6142A...
Crestron MC2E Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Page 30
2-Series Compact Control System 26 • 2-Series Compact Control System: MC2E This page is intentionally left blank. This page is intentionally left blank. Crestron MC2E Operations Guide – DOC. 6142A...
Page 31
Crestron MC2E 2-Series Compact Control System This page is intentionally left blank. 2-Series Compact Control System: MC2E • 27 Operations Guide – DOC. 6142A...
Page 32
Crestron Electronics, Inc. Operations Guide – DOC. 6142A 15 Volvo Drive Rockleigh, NJ 07647 (2008091) Tel: 888.CRESTRON 06.07 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.