Advertisement
Storing the Sound
Characteristics of each
Source
— Source Tone Memory Function
Press the
button while pressing
the
button. — "STM" will appear on
the display.
This function memorizes the adjusted sound
characteristics (the bass and treble) of each
program source. With this function, you can
listen to the same source always in the same
sound characteristics even after changing the
program source or tuning the unit off and on
again.
To cancel the STM function, press these
buttons again.
Note
When the optional XDP-U50D is connected, the STM
function will not work.
Muting the Beep Tone
Press the
button while pressing
the
button.
To obtain the beep tone again, press these
buttons once more.
Enjoying Bass and Treble
even at Low Volume
~~ Loudness Function
Press the (?) button while pressing
the
button. — "LOUD" will appear
on the display.
Bass and treble will be reinforced. To cancel,
press these buttons again.
Note
When the optional XDP-U5OD is connected, the loudness
function will not work.
Changing the Line Output
Level
(when the optional XDP-U50D and a graphic
equalizer are connected)
Press athe fe } button while pressing
the |=| button.
To cancel the mode, press these buttons again.
13
suo}uny
JayiQ/uondarsy
Ajoipey
24
DSP Function.
With the optional XDP-U50D
connected
If you connect the optional XDP-U50D, you
can add some effects to the soundfield of the
currently selected program source.
Overview of the Digital Signal
Processor (DSP) Function
The DSP can digitalize and process the audio
signal with high speed thus enabling you to
adjust the acoustic characteristics of the source
sound without losing the sound quality.
With the DSP unit you can control the audio
output and adjust the acoustic characteristics
according to your preference.
Notes
« When the optional XDP-U50D and a graphic equalizer
are connected, the reproduced sound may become
distorted if the audio output signal of the graphic
equalizer is boosted too much. In this case, press preset
number button 8 while pressing the SEL button.
This will reduce the volume, but the distorted sound can
be suppressed. To cancel the mode, press these buttons
once again. (In case the optional XDP-USOD is
connected by the optical cable, the volume will not get
reduced even if you press preset number button 8 and the
SEL button.)
© To improve the efficiency of the listening position setting,
the volume of the output sound from the rear speakers is
lowered automatically.
© When the optional XDP-U5OD is connected, the
loudness function and STM function will not work.
The DSP edit mode
The DSP function includes following select /
adjust modes:
e Surround (SUR) menu select/effect level
control mode (see page 24)
e Listening position (LP) adjust mode (see
page 26)
¢ Subwoofer (SUB) cut-off frequency / volume
contro] mode (see page 27)
¢ Bass (BAS) adjust mode (see page 27)
¢ Treble (TRE) adjust mode (see page 27)
« Fader (FAD) adjust mode (see page 28)
Left, right, front
and rear listening
position
Listening
position
Cut-off
frequency
Bass turn-over
frequency
:
Treble turn-
In addition, there are also following DSP-
related functions:
* DSP custom file function (see page 28)
¢ Last sound memory function (see page 29)
Subwoofer volume
Bass volume
Selecting the Surround
Mode
This unit features ten preset surround
modes. You can select your desired
surround mode to suit the source audio.
These modes can simulate different
soundfields so that you can enjoy the
sensation of being close to the music source
or being at a live concert etc.
surround, Menu
[HALL 33 - |
a
: Bie club
ee
oe
ae
JOLENE
ita od
A
a
Feelin
:
; | Normal mode without any DSP
ApS
ith ceiinin ts
* The surround mode will be canceled. However, other
preset levels of the DSP function menu can be
adjusted.
Advertisement
