Related Manuals for Worx WG349E
Summary of Contents for Worx WG349E
- Page 1 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 20V Cordless Pole WG349E WG349E.9 WA0307...
- Page 4 Kink...
- Page 5 0.12-0.2”...
- Page 8 6" 2" to 4" (5 a 10 cm)
- Page 9 Keep cutting tools sharp and clean. or medication. A moment of inattention while Properly maintained cutting tools with sharp operating power tools may result in serious 20V Cordless Pole WG349E WG349E.9 WA0307...
-
Page 10: Safety Warnings For Battery Pack
Recharge only with the charger specified replacement parts. This will ensure that the by Worx. Do not use any charger other than safety of the power tool is maintained. that specifically provided for use with the equipment. - Page 11 Do not expose to moisture. Warning of danger from overhead electric-power lines Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice. 20V Cordless Pole WG349E WG349E.9 WA0307...
-
Page 12: Component List
23. EXTENSION POLE LOCK-OFF BUTTON 24. EXTENSION POLE ROTATION BUTTON 25. SHOULDER STRAP HOOKS 26. SHOULDER STRAP 27. BAR TENSIONING PLATE (SEE FIG. A) * Not all the accessories illustrated or described are included in standard delivery. 20V Cordless Pole WG349E WG349E.9 WA0307... -
Page 13: Technical Data
TECHNICAL DATA Type WG349E WG349E.9 (3 - designation of machinery, representative of pole saw) WG349E WG349E.9 Voltage Max. ** Bar length 20cm Cutting length 18cm Chain speed 5.0m/s Oil tank capacity 80ml Chain pitch 0.95cm(3/8”) Number of chain drive links Chain gauge 1.1mm(0.043”) -
Page 14: Noise Data
1. Unpack all parts carefully. 2. Place the saw on a solid, level surface. VIBRATION INFORMATION 3. Use only genuine Worx chains or those recommended for Guide Bar. 4. Slide the Chain (1) in the slot around the Guide Bar Vibration total values (triax vector sum) determined (7). - Page 15 The saw head can be rotated for different cutting otherwise contaminated oils. Damage may angles for 0 , 15 , and 30 . (See Fig. I1) occur to the bar or chain. Use of non approved 20V Cordless Pole WG349E WG349E.9 WA0307...
-
Page 16: Operation
fine. If there is no oil pattern, despite a full (1) Installing the battery pack into the machine. oil reservoir, contact Worx customer service agent or (2) Make sure section of log to be cut is not laying Worx approved service agent. - Page 17 Stop Pole Saw by releasing trigger. Have damage repaired by authorized service center. To Make sure chain has stopped before setting Pole locate an authorized service center, visit www.worx. Saw down. com. 20V Cordless Pole WG349E WG349E.9...
-
Page 18: Environmental Protection
Replacing Bar & Chain Replace chain when cutters are too worn to sharpen or when chain stops. Only use replacement chain noted in this manual. Inspect Guide Bar before sharpening chain. A worn 20V Cordless Pole WG349E WG349E.9 WA0307... -
Page 19: Troubleshooting Table
EN 60745-1, EN ISO 11680-1, EN ISO 3744, EN 55014-1, EN 55014-2 Declare that the product Description Battery-powered pole saw The person authorized to compile the technical file, Type WG349E WG349E.9 (3 - designation of Name Jim Kirkwood machinery, representative of pole saw) Address Positec (UK &... - Page 20 After-sales Service and Application At www.worx.com you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: 0345 202 9679 E-Mail: customerservices@worxtools.com www.worx.com Copyright © 2022, Positec. All Rights Reserved. V0-UK- WG349E WG349E.9 WA0307-M-20220615...
Need help?
Do you have a question about the WG349E and is the answer not in the manual?
Questions and answers