Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Worx WG349
Summary of Contents for Worx WG349
- Page 1 Cordless Pole Saw WG349 WG349.9...
- Page 2 PRODUCT SAFETY appliances should be stored indoors in dry, and high or locked-up place - out of reach of children. 11) Maintain Appliance With Care - Keep cutting WARNING: Some dust created by power sanding, sawing, grinding, drilling edge sharp and clean for best performance and to reduce the risk of injury.
- Page 3 Recharge only with the charger specified g) Always use two hands when operating the pole by WORX. Do not use any charger other pruner. Hold the pole pruner with both hands to than that specifically provided for use with avoid loss of control.
- Page 4 SYMBOLS POSITEC Inc. has established To reduce the risk of injury, user a partnership with the RBRC must read instruction manual Corporation to recycle any Positec batteries with the RBRC-call2recycle seal. For environmental protection, Wear ear protection please do not discard batteries in the trash.
- Page 5 Cordless Chainsaw...
- Page 6 COMPONENT LIST CHAIN CHAIN TENSIONING KNOB CHAIN COVER SAW HEAD ADJUSTMENT KNOB LOCKING PROJECTION OIL FILLER CAP GUIDE BAR OIL LEVEL WINDOW DRIVE SPROCKET 10. CHAIN DIRECTION SYMBOL 11. BAR LOCATING TABS 12. FASTENING BAR BOLT 13. BAR PAD 14. BUMPER SPIKE 15.
- Page 7 Charger (WA3881) Battery pack(WA3575) Auxiliary Handle Bar & Chain Sheath Only use the appropriate accessories intended for this tool. Accessory information can be found on the product packaging, at a WORX dealer or on our website at www.worx.com. Cordless Chainsaw...
- Page 8 Kink...
- Page 9 0.12-0.2” EN: Bar / F: Bar ES: Barra de guía...
- Page 12 6" 2" to 4" (5 a 10 cm) EN: Injecting grease to lubricate F: Injectez la graisse pour lubrifier ES: Inyectando grasa para lubricar...
- Page 13 EN: Injecting grease to lubricate F: Injectez la graisse pour lubrifier ES: Inyectando grasa para lubricar Cordless Chainsaw...
- Page 14 4. Fully tighten the Chain Tensioning Knob (2) by 2. Place the saw on a solid, level surface. turning it clockwise. 3. Use only genuine WORX chains or those recommended for Guide Bar. 5. Double check the tension set by the automatic Chain Tensioning Knob.
- Page 15 NOTE: Failure to properly secure the pole saw operating fine. If there is no oil pattern, despite a full head may result in personal injury and/or property oil reservoir, contact WORX customer service agent damage. or WORX approved service agent.
- Page 16 NOTE: When removing the battery pack, hold it This saw has a low-kickback chain and reduced firmly to avoid dropping and injury. kickback Guide Bar. Both items reduce the chance of kickback. However, kickback can still occur with this 4. SWITCHING ON AND OFF (See Fig. M) saw.
- Page 17 Pole Saw damage affects safety or operation. Have damage down. repaired by authorized service center. To locate an authorized service center, visit www.worx.com. TRIMMING A TREE (PRUNING) WARNING: Avoid kickback. Kickback can 3. Maintain pole saw with care.
- Page 18 the pole saw. Replacing Bar & Chain Replace chain when cutters are too worn to sharpen or when chain stops. Only use replacement chain noted in this manual. Inspect guide bar before sharpening chain. A worn or damaged guide bar is unsafe. A worn or damaged guide bar will damage chain.
- Page 19 Applying relatively less pressure while Pole saw cutting. cutting operates Loose connection. intermittently Contact service agent 1-866-354-WORX Internal wiring defective. (9679). On/Off Trigger defective. No oil in reservoir Refill oil Dry chain Vent in oil filler cap clogged...
- Page 22 Copyright © 2019, Positec. All Rights Reserved. Copyright © 2019, Positec. Tous droits réservés. © Derechos reservados 2019, Positec. Todos los derechos reservados.