Advertisement
Remove packing tape from brewer and plug into a grounded outlet.
Place a large mug (12oz. minimum) on the drip tray plate.
Remove the water reservoir lid, then lift the reservoir straight up to remove it.
If you have a Keurig® Water Filter, install it now. Refer to your Water Filter Starter Kit for instructions.
Rinse reservoir with fresh water and fill to the MAX fill line.
Replace water reservoir, making sure the lock tab engages with the brewer. Replace lid.
NOTE: Do not use distilled water.
Press power button — the green power light and Auto Off light will illuminate.
The brewer will automatically begin heating the water. This will take about 3 minutes. Once the heating sound stops, the brewer is ready.
Lift and lower the handle. Do not insert a K-Cup® pod. The four brew buttons and the Strong button will blink.
Press the small cup button to start a cleansing brew. Pour the hot water into the sink.
The one-time setup process is now complete and you are ready to brew!
Place a mug on the drip tray plate. If using a travel mug, remove the drip tray and place the mug on the drip tray base. NOTE: Between brew cycles, the brewer may take about a minute to reheat.
Lift the handle and place a K-Cup® pod in the K-Cup® pod holder. Lower the handle completely to close the lid. Do not remove the foil lid on the K-Cup® pod.
Select your brew size – for bolder coffee, press the Strong button before selecting your brew size. The brew size and Strong button, if selected, will remain illuminated while brewing – about 1 minute. The brewer will be ready to brew another cup in about a minute. NOTE: After 60 seconds, the brew buttons will be disabled. To re-activate, lift and lower the handle completely.
While brewing, there is extremely hot water in the K-Cup® pod holder. To avoid injury, do not lift the handle during the brewing process.
Strong Brew kicks up your coffee's strength and intensity. For bolder coffee, press the Strong button before selecting your brew size.
Smart Start heats then brews in one simple process. No need to wait for the brewer to heat before selecting brew size. Power on your brewer, place mug, insert a K-Cup® pod, and lower the handle. Then, select your brew size. The brewer will heat, then automatically begin brewing.
Auto Off automatically turns your brewer off 2 hours after the last brew for energy savings.
To disable the Auto Off feature:
To enable the Auto Off feature, repeat steps 1-3. The green Auto Off light will illuminate.
High Altitude Brewing: To ensure your brewer works properly at higher altitudes (5,000 feet) please follow these brewing instructions and enable the High Altitude Brewing Mode on your brewer. Brewing Instructions - While holding the brewer handle up, push down slowly on the K-Cup® pod in the pod holder until the bottom of the K-Cup® pod is punctured by the exit needle.
To enable High Altitude Brewing Mode:
To disable High Altitude Brewing Mode:
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
Keep your Keurig® brewer looking its best by cleaning the exterior from time to time. Just clean with a damp, soapy, lint-free, non-abrasive cloth. Never immerse the brewer in water or other liquids.
The drip tray can hold up to 8 ounces of overflow and should be emptied and cleaned occasionally. To remove, slide it toward you, keeping it level to avoid spilling. Clean in dishwasher (top rack only) or rinse and clean with a damp, soapy, lint-free, non-abrasive cloth.
The water reservoir lid and water reservoir should be cleaned periodically. Clean in a dishwasher (top rack only) or hand wash. To hand wash, use a damp, soapy, nonabrasive cloth. Rinse the reservoir thoroughly after cleaning. This will ensure that no cleaning solutions remain in the area as they may contaminate the water supply. After rinsing, fill the reservoir with clean water and return it to the brewer. Do not dry the inside of the water reservoir with a cloth as lint may remain. If needed, repeat above procedures.
NOTE: If you are using a water filter inside the water reservoir, remove it before cleaning.
To remove the K-Cup® pod holder from the brewer, lift the handle and grasp the top of the K-Cup® pod holder with one hand while pushing up on the bottom of the K-Cup® pod holder from underneath with the other until it releases. After cleaning, align the K-Cup® pod holder with the opening using the two front ribs as a guide and snap into place from the top.
There are sharp needles that puncture the K-Cup® pod above the K-Cup® pod holder and in the bottom of the K-Cup® pod holder. To avoid risk of injury, do not put your fingers in the K-Cup® pod holder.
The funnel can be removed from the K-Cup® pod holder by pulling on it until it pops off. To replace it, just snap it back onto the K-Cup® pod holder.
Remove the pod holder assembly and detach the funnel. Locate the exit needle on the inside bottom of the K-Cup® pod holder. Insert a straightened paper clip into the exit needle to loosen the clog and push it out.
Lift the brewer handle and locate the entrance needle on the underside of the lid. To clean both holes in the needle, hold the brewer handle in the upward position and with your other hand, carefully insert a straightened paper clip into both holes. Gently move it around to loosen any coffee grounds. Lower the handle completely and run two water-only brew cycles. Do not insert a K-Cup® pod.
TIP: Refer to support.Keurig.com for video instructions on cleaning the entrance/exit needles.
You should descale your brewer every 3-6 months. Properly follow the descaling procedure.
Depending on the mineral content of your water, calcium deposits or scale may build up in your brewer. Scale is nontoxic but if left unattended can hinder brewer performance. Regularly descaling your brewer every 3-6 months helps maintain the heating element, and other internal parts that come in contact with water. Calcium deposits may build up faster, making it necessary to descale more often.
Before you begin, you will need a large ceramic mug, fresh water, Keurig® Descaling Solution, and access to a sink. Do not use a paper cup. Ensure that there is no beverage pod in the K-Cup® pod holder. Please allow approximately 45 minutes for the descaling procedure.
Empty the water from the water reservoir. If using a Keurig® Water Filter, remove and set aside.
STEP 1: Descaling Solution Rinse
Press the power button to power the brewer off.
Pour the entire bottle of Keurig® Descaling Solution into an emptied water reservoir. Then fill the empty bottle with water and pour into the water reservoir. Press the power button to turn the brewer back on.
Place a large mug on the drip tray and run a rinsing brew by lifting and lowering the handle and selecting the largest brew size.
STEP 2: Descaling Rinse & Repeat
Repeat the rinsing brew process until the add water light is illuminated. Do not use a K-Cup® pod. Let brewer stand for at least 30 minutes while still on.
After 30 minutes, discard any residual solution from the water reservoir and rinse thoroughly.
STEP 3: Fresh Water Rinse
Fill the water reservoir with fresh water to and not beyond the MAX fill line.
Place a large mug on the drip tray plate and run a rinsing brew using the largest brew size. Do not use a K-Cup® pod. Pour the contents of the mug into the sink.
Repeat brew process until you have completed at least 12 rinsing brews using the largest brew size. You may need to refill the water reservoir at least one time during this process.
NOTE: The cleaning action of Keurig® Descaling Solution may result in a "foam" dispensed from the brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added. If this occurs, you may see only a small or no output dispensed, followed by the sound of air blowing out. If this occurs:
Grounds may have gathered in the exit or entrance needles and can be cleaned using a straightened paper clip or similar tool.
Water quality varies greatly. If you notice an undesirable taste in your beverage (such as chlorine or mineral tastes), we recommend using bottled or filtered water. Do not use distilled water. You can also install a Keurig® Water Filter to help remove water impurities and improve beverage taste.
Beyond these recommended cleaning and maintenance procedures, this brewer is not user serviceable. For service, please refer to the Warranty section of this guide.
Empty the water reservoir before storing or transporting and take care to ensure that you store your brewer in a safe and frost free environment. Please be sure to store your brewer in its upright position to avoid water leakage from the inner tank. If you store the brewer in a cold environment, you run the risk of water freezing inside the brewer and causing damage. When you prepare to use it after storage, we recommend rinsing the water reservoir with fresh water and running three rinsing brews without a K-Cup® pod.
If you plan to move your brewer to a different location, turn the brewer off, unplug it, and empty the water reservoir. If your brewer has been in an environment below freezing, please be sure to let it warm to room temperature for at least 2 hours before using.
Have Questions?
We're here to help. Visit support. Keurig.com for step-by-step videos on cleaning, descaling, and more.
Still Need Help?
Give us a call at
1-866-901-BREW (2739)
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the K-Select that isn't answered in the manual? Leave your question here.