Advertisement
"Tv"
3-3 Remote Control Unit Learning Function
1
DENON
=
|
-
|
Erin
as Coe ae
3 (PHONO)
MITSUBISHI A { MITSUBISHI B | MITSUBISHI C
4(TUNER)
| PANASONIC
5 (VCR-1)
JVC {VICTOR)
6 (VCR-2)
SONY
7?
PIONEER
8 (CD)
TOSHIBA
9 (MULTI)
SANYO A
10(V.AUX/GAME)|
SHARP
1V/O(DAT/TAPE}|
NEC A
T2/E
PHILIPS A
STEREO
RCA A
5. Check that the START LED is lit, then
press the button to be "learned" on
the other remote control unit.
1. Press the USE/LEARN selector but-
ton with the tip of a pen etc., to set
the learn mode. Both the START and
LEARNED/TX indicators flash.
Flashes
+
<>
S
SANYO
B
NEC B
PHILIPS B
This unit's remote contro! unit
6.Once the START LED turns off and
the
LEARNED/TX
LED
lights,
re-
tease the button on the other remote
5
Set to the AUDIO side for the CD,
control unit.
MODE
| GENERAL *
GENERAL =
Preset memory function will not work for some
tape deck or DAT position, to the
u
models or some codes.
VIDEO side for the CDP, VCR or TV
TONE/DIRECT | MAGNAVOX A | MAGNAVOX B | MAGNAVOX C
In such case, please use the fearning function.
position.
A
eClearing the Preset Memory
AVRIANE NIDES."
1.Press the USE/LEARN selector but-
4.Press the SYSTEM CALL SET but-
ton with the tip of a pen, etc., to set
ton, and hold it in for at least four
the learn mode.
+
ey a
2.Set the slide switch to "VIDEO".
3. Set the program switch to the posi-
tion to be
"learned".
The two LEDs start flashing again.
7.To
"learn"
other
buttons,
repeat
steps 4 and 5.
4. Set the remote control units so they
are facing each other, then
press the
button to be "learned" on this unit's
remote control unit.
9.For instructions on resetting
the "learned" codes, refer to
"clearing the Preset Memory".
8. Once the learning operation is com-
pleted, press the USE/LEARN selec-
tor button again.
The two LEDs stop flashing and the
learning mode is cancelled.
5.When
both
the
START
and
LEARNED/TX
LEDs
light
simul-
taneously, all the stored codes are
'Other remote
cleared.
control unit
1
AVRIAVG VIDEO~
This unit's remote
control unit
#<ED
OF
e ie
3.Set the program switch to the side
to be cleared.
Bi: DECK DAY
—VvOP VCR W
The indicator stops flashing and the
START LED lights.
The learnable buttons are the but-
tons which can be operated with the
DENON
system
codes for the CD
player, DAT and tape deck, the but-
NOTES:
-
:
tons which can be operated with the
e Up to 26 codes can be "learned", but this number
may be lower if the
preset memory for the VCR, VDP
codes are long.
,
and TV. For the TV only, however,
e If a non-learnable button is pressed or two or more buttons are pressed at
the buttons in the section indicated
once, the. two LEDs will once again light when the button({s} is released.
"A" on the diagram above can also
e If the codes could not be stored, the LEARNED/TX LED does not light after
be "learned". Use these to "learn"
the START LED turns off. (This may happen for a limited number of
TV channels.
models.)
'
:
:
© If the two LEDs start flashing rapidly after the START LED lights, this means
that the memory is already full, and the code you have just attempted to
store was not stored.
To "learn" that code, first perform the resetting operation.
2, if
5
Check that the stored codes work
properly.
Ojo
Ex.: To
clear
memory
the
VDP
preset
Advertisement
