Advertisement
PANEL FACILITIES
(2 MODE display
60
150
900
1 x
@) EQ ON indicator
Lights when the EQUALIZER switch is set to ON. When this indicator
is lit, the graphic equalizer can be used to adjust sound quality.
MEMORY indicator
When the line under ''MEMORY'' is lit, it indicates that the equalization
curves you input in the memory recall switches can be recalled.
© A — E indicators
Indicates which equalization curve is currently recalled.
A: Curve stored in A/CAR. (Preset CAR or Memory A)
B: Curve stored in B/PHONES.
(Preset PHONES or Memory B)
C: Curve stored in C/VOCAL.
(Preset VOCAL or Memory C)
D: Curve stored in D/HEAVY.
(Preset HEAVY or Memory D)
E: Curve stored in E/CLEAR. (Preset CLEAR or Memory E)
@) PRESET indicator
When the line under '7PRESET'' is lit, it indicates that the equalization
curves factory preset in the memory recall switches can be recalled.
© REVERSE indicator
Lights when FLAT/REVERSE switch is used to invert the equalization
curve.
@3) EQUALIZING CONTROL switches
These strengthen or weaken the indicated frequency band. Press the
upper switch to emphasize; press the lower switch to attenuate.
FLAT/REVERSE switch
Press once to reset the equalizer to flat response (no equalization). Press
again to reverse
a previous
curve
(boosted
frequencies
will be
attenuated, and vice versa).
(3) Memory recall switches
Used for recalling equalization curves.
PRESET/MEMORY switch
Determines whether the equalizer curves recalled by the Memory recall
switches are your memorized curves or factory preset curves.
@) MEMORY switch
Used for storing equalization curves you input in the memory recall
switches.
(8) EQUALIZER ON/OFF switch
Turns the equalizer on and off. The EQ ON indicator lights when this
switch is on.
The equalizer can not be used to adjust the sound when CD DIRECT
or DAT DIRECT is on.
(@ Cassette Tape Deck Section
Cassette door
12
<ARB1218>
DOLBY* NR switch
Set this switch to B or C fore recording with the built-in Dolby NR
systems and for playback of tapes which have been recorded using the
Dolby NR systems.
It is recommended that tapes recorded with Dolby NR (Type B or Type
C) be so marked on the label. This will help prevent incorrect setting
of the noise reduction switch during playback.
*
Dolby
noise
reduction
manufactured
under
license
from
Dolby
Laboratories Licensing Corporation.
"DOLBY"
and the double-D symbol!
DO
are trademarks of Dolby
Laboratories Licensing Corporation.
@i) RELAY RECORDING switch
Use for relay recording from Deck | to Deck II.
Deck [| starts recording when Deck | finishes.
To use put both decks in stop mode.
@) PARALLEL RECORDING switch
Deck | and Deck II record at the same time.
To use put both decks in stop mode.
@) Operation indicators
<j
Rec
(C
~—_—e
—
<j
REC
WH
DECK
IW, RELAY
FADE
,
DECK
A
RELAY > PARA + FREE «aces moor
@) Direction
(<1, > ): Indicates direction of tape travel during recording
or playback. Flashes slowly in pause mode. Flashes rapidly during
Music Search (MS).
REC: Lights when recording.
© RELAY:
Indicates relay recording in progress using Deck | and
Deck II.
@ FADE: Lights when AUTO FADER switch is on.
©, ASES MODE
RELAY: relay edit in progress.
PARA: parallel edit in progress.
FADE: fade edit in progress.
@ AUTO FADER switch
Used for gradually fading out a recorded tape in Deck Il. (The sound
will be completely cut off after approximately 10 seconds and the tape
will stop.)
@) DECK Il COUNTER
@) Counter reset switch
Press this switch to reset the Deck I! tape counter display to OOO.
@) SYNCHRO COPY switches
Used for tape copying.
NORMAL:
Copying from the Deck | tape to the Deck I! tape at normal
recording/playback speed.
HIGH:
Copying at about twice normal tape speed. (Copies can be
made in about half the NORMAL time.)
Advertisement
