CLIVET WiSAN-YEE1 45.4 Manual page 54

Data
Reg
Type
136 S16
137 S16
138 S16
139 S16
140 S16
141 S16
142 S16
143 S16
144 S16
145 S16
146 S16
147 S16
148 S16
149 S16
150 S16
151 S16
152 S16
153 S16
154 S16
155 S16
156 S16
157 S16
54
R/W Name
R&W Inverter pump enable
Inverter pump running
R&W
speed
R&W Modbus control enable
R&W Gycol type
R&W Glycol percentage
R&W Paf offset
R&W Water coil control
R&W DtTws
R&W Dtmix
R&W FC Offset
R&W FC Hyster
R&W TWI_O ABNORMAL
R&W Low outlet water control
R&W Power limit
R&W E9 protection time
R&W E9 detection method
R&W Inverter pump MIN speed
R&W Inverter pump MAX speed
R&W Pump turn on time
R&W Pump turn off time
R&W TW_COOL_DIFF
R&W TW_HEAT_DIFF
Description
Range: 0 - Disable, 1 - Enable , Default: 0 - Disable , Unit of
measurement: - , Notes: Valid only for single pump system
Range: 30 ~ 100 , Default: 100 , Unit of measurement: [%] ,
Notes: 5% step. Only valid if register 136 is enabled
Range: 0 - Disable, 1 - Enable , Default: 0 - Disable , Unit of
measurement: - , Notes: Enable this item bofer writing other
Modbus registers
Range: 0 - Ethylene, 1 - Propylene , Default: 0 - Ethylene , Unit
of measurement: - , Notes:
Range: 0 ~ 50 , Default: 0 , Unit of measurement: [%] , Notes:
5% step
Protection pressure compensation , Range: 0 ~ 20 , Default: 0
, Unit of measurement: 0.01Mpa , Notes: step of 5
Range: 0 - Automatic, 1 - Manual1 (through), 2 - Manual2
(bypass) , Default: 0 - Automatic , Unit of measurement: - ,
Notes: Valid only on FC units
Tws rising value after entering mix , Range: 1 ~ 3 , Default: 1 ,
Unit of measurement: [°C] , Notes: Only valid for FC/CO unit
Enter mix hysteresis , Range: 1 ~ 3 , Default: 2 , Unit of
measurement: [%] , Notes: Only valid for FC/CO unit
FC enter offset , Range: 1 ~ 15 , Default: 3 , Unit of
measurement: [°C] , Notes: Only valid for FC/CO unit
FC enter hysteresis , Range: 1 ~ 3 , Default: 1 , Unit of
measurement: [°C] , Notes: Only valid for FC/CO unit
Abnormal differ bettween inlet and outlet water temperature ,
Range: 1 ~ 5 , Default: 2 , Unit of measurement: [°C] , Notes:
Range: 0 ~ 20 , Default: 7 , Unit of measurement: [°C] , Notes:
Energy saving level , Range: 40 ~ 100 , Default: 40 , Unit of
measurement: [%] , Notes: 10% step
Water flow switch protection time , Range: 2 ~ 20 , Default: 5 ,
Unit of measurement: [s] , Notes:
Range: 0 - Water flow detected before the pump is turned on,
, 1 - Water flow switch is detected after the pump is turned on ,
Default: 0 , Unit of measurement: - , Notes:
Range: 40 ~ Max(100, Inverter pump MAX speed) , Default:
75 , Unit of measurement: [%] , Notes: 5% step. Only valid for
multiple pump system
Range: MIN(70, Inverter pump MIN speed) ~ 100 , Default:
75 , Unit of measurement: [%] , Notes: 5% step. Only valid for
multiple pump system
Range: 5 ~ 60 , Default: 5 , Unit of measurement: [min] , Notes:
5 min step
Range: 0 ~ 60 , Default: 0 , Unit of measurement: [%] , Notes:
5 min step
Differential temperature Tw in cooling mode , Range: 1 ~ 5 ,
Default: 2 , Unit of measurement: [°C] , Notes:
Differential temperature Tw in heating mode , Range: 1 ~ 5 ,
Default: 2 , Unit of measurement: [°C] , Notes:
Modbus