Cal-Royal N-FMR7700 Series Installation Instruction

INSTALLATION INSTRUCTION FOR
N-FMR7700 SERIES MORTISE EXIT DEVICE
BEFORE INSTALLING DEVICE, PLEASE CHECK:
1. IF DOOR FITTED AND HUNG.
2. SIZE OF EXIT DEVICE, FUNCTION AND DESIGN ...
2.1. 36"DOORS, CAN BE CUT TO FIT DOORS DOWN TO 30" WIDE.
2.2. 48"DOORS, CAN BE CUT TO FIT DOORS DOWN TO 36" WIDE.
2.3. HAND OF DEVICE AGAINST APPLICATION.
RIGHT HAND
��
REVERSE BEVEL
�
CHASSIS
ASSEMBLY
HORIZONTAL
�CHASSIS
1. PREPARE DOOR AND MOUNT LOCK
Tape templates to inside face and edge of doors according to
directions given on template. Drill holes and mortise door for
lock as indicated.
Fasten mortise lock in plate
NOTE:lf screwless rose trim
is used -- refer to trim
instructions and mount
lock in conjunction with
rose and inner plates
#12-24x1"
2. ATTACH CHASSIS TO DOOR
2.1 Attach chassis to Rail, then lock
push rail down.using
2.2 Position chassis and rail on door,
so that lever arm is under rear
section of Mortise lock lever.
Then lift up until latchbolt is
completely retracted.
2.3 With chassis in this position and
rail horizontal, mark location of
chassis mounting holes. Drill holes
for screws.
2.4 Release Push rail, and dis-ass'y
chassis from rail.
Then, mount chasis on door.
OUT
LEFT HAND
•
REVERSE BEVEL
�
'i,_
vERTIcAL OF cHAssIs
2-3/4"
TO FINISHED FLOOR
FROM TEMPLATE
OR FROM RELATIONSHIP
TO STRIKE
INSIDE FACE
OF DOOR
<t_ LATCH BOLT
DEPRESS ARM INTO RAIL OPENING AND
SLIDE RAIL ONTO CHASSIS
PUSH RAIL
RAIL ASSEMBLY
r-------
LATCH BOLT
C AL-R O YAL
SURFACE OF DOOR FOR
EXIT DEVICE APPLIED MUST
BE FLUSHED.
3. APPLY EXTERIOR TRIMS
If ESC lever trim is used, attach outside trim and cylinder.
4. APPLY RAIL ASSEMBLY
1. CHECK THE SIZE OF DEVICE, IF CUTTING TO LENGTH IS REQUIRED.
2. DETERTMINE CUT OFF LENGTH "X" BY SUBTRACTING 1-3/4" (44.5mm)
FROM "Y". MARK CUT OFF POINT ON MOUNTING RAIL.
f �:
VERTICAL
CHASSIS
=======-·
I i •
1------��------i·
t-------Y�------i
3. DEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO
CHASSIS. LEVEL RAIL AND FASSTEN CHASIS AND MOUNTING
PLATE.
i
\ RAIL ASSEMBLY.
5. APPLY COVER AND STRIKES
CHASSIS
ATTACH COVER TO CHASSIS
WITH (4) #8 TRUSS HEAD
MACHINE SCREW.
END CAP
RAIL MOUNTING
BRACKET
FOR DOOR W/STILE
CUT OFF MUST LEAVE
1/2" MIN OVERLAP
! �
WITH RAIL
::r-----, (
-l
1-3/4" MIN
X
(44.5 mm)
LEVEL
lj
MOUNTING PLATE SCREWS
D D
LEFT RIGHT
ATTACH END CAP TO ATTACH STRIKE TO
MOUNTING PLATE WITH DOOR STOP WITH (2), STRIKE
(2) COVER SCREWS. SCREW AND LOCK WASHER
CUT OFF AND DEBURR
DON'T CUT CLOSER THAN
1-3/4" (44.5mm) FROM LOWER PIUOT.
ATTACH MOUNTING PLATE TO
DOOR WITH (2) ROUND HEAD
SCREWS.
LEFT RIGHT
ATTACH STRIKE TO
DOOR STOP WITH (2), STRIKE
SCREW AND LOCK WASHER
1-2
DRWG. # EDG4026