Table of Contents
Advertisement
Connecting the TV to a SBB or STB
STB (SBB)
ETH MODEM
Connect the DATA port of the TV to the ETH MODEM port of the STB
(SBB) with the Data cable.
• The ETH MODEM port name that you connect the Data Cable to
may differ depending on the SBB or STB type.
• IR signals sent by the remote control to the TV or SBB / STB must
meet the following specification to use IR pass through function.
IR signal receiver specification
– Band pass filter center frequency: 37.9 ㎑
– Carrier Frequency, Duty 50%
– Minimum Burst Length (tburst): 12 pulses (316 us)
– Minimum Gap Time Between the burst (tburst gap): 16
pulses (422 us)
– Minimum Gap Time between the data commands (tpause):
25 ㎳
List of Hospitality SI Vendors and compatible data
cables supplied with the TV
• Confirm you are using the correct data cable for your SI vendor.
Refer to the code label on the data cables.
• Contact your nearest dealer or your SI Vendor to buy the data
cable not included in the TV.
TV side
5
4
Confirm the code on the Code Label.
3
2
1
Cable code
TV SIDE
BN39-02462A
1: NC
2: RX
3: TX
(Color: BLACK)
4: IR
5: GND
BN39-02461A
TV SIDE
1: CLK
(Color: LIGHT
2: RX
3: TX
4: IR
GRAY)
5: GND
• RX and TX notation is based on TV.
• Operation Specification of Data Cable(RJ12): RS232
TV Rear Panel
Data Cable
STB (SBB) side
Pin assign
REMARK
P1
P2
STB (SBB) SIDE
SAMSUNG
RED
1: IR
1
3
GREEN
2: GND
2
5
3: NC
WHITE
3
6
4: NC
and others
BLACK
5: RX
4
1
YELLOW
6: TX
5
2
P1
P2
STB (SBB) SIDE
RED
1: IR
1
6
GREEN
2: GND
2
5
3: TX
WHITE
3
3
4: NC
BLACK
5: RX
4
1
YELLOW
6: CLK
5
2
Connecting a Pillow Speaker
You can connect a pillow speaker to the TV in the hospital using a
jumper cable. The speaker functions as a remote control and speaker.
Jumper Cable
Pillow Speaker
1. Connect the pillow speaker jumper cable (cable sold separately)
from the television's PILLOW SPEAKER Port to the pillow speaker
jack on the wall behind the television.
Pillow Speaker Jack Specifications
• Output jack: RCA type
• Input jumper pin: 1/8" 3-conductor stereo phone pin.
• Signal specifications: Tip-Audio, Ring-Data/Channel change,
Sleeve-Common
Tip
How to Use the Pillow Speaker
"
To use Pillow Speaker, be sure to set the Pillow Speaker Mode
item to on in the Hospital mode setup menu.
• Analog type speaker: The pillow speaker has one key.
– Power On: press the key when the TV is in standby mode.
1
– Channel Up: press the key when the speaker is on.
6
– Power Off: press and hold the key for more than 3 seconds
when the speaker is on.
– An Analog type speaker always works regardless of the
Pillow Speaker Type value set in the Hospital mode setup
menu.
• Digital type speaker: The TV supports the Samsung, Philips, or
Zenith code.
– This speaker is only compatible with a specified IR code. You
can change the code in the Hospital mode setup menu.
– The TV gives priority to the Samsung remote control over the
pillow speaker's wired remote control.
MTI
– Option: Channel Menu Display.
English - 10
TV Rear Panel
Ring
Sleeve
Advertisement
Table of Contents
