Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for INDUSVISION iCUBE Series
Summary of Contents for INDUSVISION iCUBE Series
- Page 1 Product instruction Manual...
- Page 2 Product User Manual iCUBE-PS,PD Series Notice on Copyright and Trademark Usage Products and company names mentioned in this manual are trademarks or registered trademarks belonging to the company. WARRANTY If the product is not normally installed due to a defect under normal use conditions, The manufacturer will repair it free of charge through the place of purchase.
- Page 3 Outline Index PC System Recommended Specifications • Component Information * CPU: Intel Core 2 Duo 2.4 GHz or higher (when using 1920x1080 30fps) Intel Core i7 2.8 GHz or higher (when using 1920x1080 60fps) • Product Classification and part names * Resolution: 1280x1024 or higher (32-bit color) •...
-
Page 4: Component Information
Component notes Spare Bolt (M3*4, M4*2) * The sun shield is shipped attached to the iCUBE Series product. * The power supply is AC-24V for the iCUBE Series. * Multi-cable may not be provided depending on some specifications. * Cable glands may not be provided on some models or may be replaced with sealing fittings. - Page 5 Product Classification and Part Names Please be aware of the part names for each product as they are important for providing quick and accurate service for problems in each part. iCUBE Series ICUBE-PD ICUBE-PS Details Details Series Model Details ICUBE-PS-100...
-
Page 6: Checklist Before Product Installation
Checklist before product installation Check product operation information and appearance status Check the specifications of the L wrench [ICUBE-PS] [Box] * On the product label on the product packaging box and on the tag on the sunshield portion of the product [ICUBE-PD] After checking the information necessary for initial operation such as IP address, ID, password, etc. - Page 7 Select product installation location When selecting a location to install the product, be sure to install it in a place that does not have any inconsistencies as in the case below. Things to consider when installing the product When selecting the initial location to install the product, please consider the following. Check whether the size of the ‘pedestal mount bracket’...
- Page 8 Product installation and precautions The manufacturer is not responsible for any problems caused by installing a bracket other than the genuine bracket provided by the manufacturer. Pole installation using pedestal mount bracket Wall installation using wall mount bracket - Use the provided hex bolt set to fasten the bolts to the bolt holes between - The wall mount bracket can be fixed to a vertical wall.
- Page 9 Product installation and precautions Product defects due to connection errors between the power terminal and RS-485 terminal connector are considered customer negligence and will be repaired at a cost. The ICUBE-PS and PD Series have a built-in hub, so they can operate normally when only one NETWORK cable is connected. Cable connection SETP 2 Cable connection SETP 1 AC-24V...
- Page 10 Product installation and precautions Incorrect operation of options may cause malfunction or malfunction of the product. OPTION S/W functions may change depending on the product. Front Panel Option setting table in A Type Panbase Option operation by PRESET number FUNCTION S/W 1 BUILT-IN EXTERIOR Operation function by preset number...
-
Page 11: Ground Installation
Product installation and precautions The manufacturer is not responsible for damage to the product due to lightning, surge, etc. due to failure to ground the product. Ground installation Fastening of sunshield... - Page 12 Installation completed and inspected Manufacturers strongly recommend that all devices undergo final testing prior to installation at their final installation location. Finalization of product installation Junction box internal wiring [220V] [AC-24V-] [HUB] [Cat5e Cable] [RS-485 Joystick] [Inside the junction box] - Once the cable installation and explosion-proof flexible installation is - After all installation is complete, install the AC 24V adapter included with the complete, close the M3*6 bolts on the fan service cover using a Phillips...
- Page 13 Maintenance after product installation When replacing or maintaining the camera, move to a safe area without humidity and static electricity. Replacement of external BOX camera Open Camera Housing Cover ※ Depending on the camera height, an offset bracket must be installed. - As shown in , check whether the center of the camera matches the - To install the camera, remove 4 M4*12 wrench bolts from the Camera...
-
Page 14: Wiper Replacement
Maintenance after product installation The manufacturer only guarantees the use of genuine parts guaranteed by the manufacturer for parts used during device maintenance. Cleaning of GE Glass Protection Grid Wiper replacement ※ Wiper Blade SET - Through routine cleaning, the product must be managed periodically to prevent more - For models equipped with wipers, the blades may wear out and video than 5 mm of dust from accumulating on the surface. -
Page 15: Network Connection And Setup
Network Connection and Setup You can set the network environment of the camera according to the user's network connection configuration. Installing the camera directly in a LAN environment Installing the camera directly in a LAN environment External remote pc CAMERA CAMERA Internet External remote pc... - Page 16 Network Connection and Setup The IP address range of the user's computer and the IP address range of the camera must match for normal web viewer access. Using the IP Search program PC network settings depending on whether an IP sharer is used Network settings Network settings Control Panel >...
- Page 17 Network Connection and Setup Web viewer access can be checked in normal operation through Google Chrome and Microsoft Edge browsers. Change IP Settings in Web Viewer Web viewer access Please log in to access this site. Authorization required for HTTP://10.20.30.40 Your connection to this site is not secure.
-
Page 18: Rtsp Settings
Network Connection and Setup When setting RTSP, you must first check if the ‘554 PORT’ of the router is open. Firmware update method RTSP settings - Press the ‘ADMIN’ icon at the top of the web viewer to enter the SETUP menu. - Service: Set whether to use RTP/RTSP. - Page 19 Installation inspection check sheet 1. When receiving the product, before on-site installation, please check the pre-checklist in the following order and only install on-site if there are no problems. 2. Please note that in some cases, service measures may be provided at a cost for problems that occur during on-site delivery without prior checklist inspection.
- Page 20 Technical drawing – ICUBE Series Please refer to the technical drawings and review the site situation before and after product installation. ICUBE-PS Series ICUBE-PD Series...
- Page 21 Technical drawing – Mount bracket Please refer to the technical drawings and review the site situation before and after product installation. Wall mount bracket Pedestal Mount Bracket...