Advertisement

Quick Links

450SS S
Owner's Manual
READ THIS
MANUAL
CAREFULLY
It contains important
safety information
Make sure operator holds a valid driver license.
Passengers under 12 are prohibited.

Advertisement

Table of Contents
loading

Summary of Contents for CF MOTO 450SS S

  • Page 1 450SS S Owner's Manual READ THIS It contains important Make sure operator holds a valid driver license. MANUAL safety information Passengers under 12 are prohibited. CAREFULLY...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS FOREWORD ������������������������������������������������������������������������������������������������ 8 EVAP System (Evaporative Emission Control System) ������������������������������������������������9 Signal Words ���������������������������������������������������������������������������������������������������������������10 INTRODUCTION ���������������������������������������������������������������������������������������� 12 VIN AND ENGINE SERIAL NUMBER ������������������������������������������������������� 13 SPECIFICATIONS �������������������������������������������������������������������������������������� 14 OPERATOR SAFETY �������������������������������������������������������������������������������� 17 General Safety Precautions ����������������������������������������������������������������������������������������17 Equipment Modifications ���������������������������������������������������������������������������������������������18 Owner Responsibilities ������������������������������������������������������������������������������������������������21 Safe Riding Gear ���������������������������������������������������������������������������������������������������������22 AVOID DANGEROUS RIDING BEHAVIORS ��������������������������������������������...
  • Page 3 Front Hand Brake Lever ����������������������������������������������������������������������������������������������33 Handlebar Switch, LH �������������������������������������������������������������������������������������������������34 Handlebar Switch, RH �������������������������������������������������������������������������������������������������35 Throttle Grip ����������������������������������������������������������������������������������������������������������������35 Locks ���������������������������������������������������������������������������������������������������������������������������36 Gear Shift Lever ����������������������������������������������������������������������������������������������������������38 Rear Brake Lever ��������������������������������������������������������������������������������������������������������39 Side Stand �������������������������������������������������������������������������������������������������������������������39 Passenger Handhold and Footrests ����������������������������������������������������������������������������40 INSTRUMENT �������������������������������������������������������������������������������������������� 41 Activation and Testing �������������������������������������������������������������������������������������������������41 Instrument Indicators ���������������������������������������������������������������������������������������������������42 Instrument Display ������������������������������������������������������������������������������������������������������45 Instrument Menu ���������������������������������������������������������������������������������������������������������52...
  • Page 4 Brake ���������������������������������������������������������������������������������������������������������������������������86 Parking ������������������������������������������������������������������������������������������������������������������������87 SAFETY OPERATION ������������������������������������������������������������������������������� 88 Safe Riding Tips ����������������������������������������������������������������������������������������������������������88 Additional Cautions for High Speed Operation �����������������������������������������������������������89 MAINTENANCE ����������������������������������������������������������������������������������������� 90 Improper Use �������������������������������������������������������������������������������������������������������������90 Key Points of Lubrication Schedule ����������������������������������������������������������������������������91 Break-In Maintenance Chart ���������������������������������������������������������������������������������������92 Periodic Maintenance Chart ����������������������������������������������������������������������������������������95 CLUTCH LEVER FREE PLAY ����������������������������������������������������������������� 101 GEARSHIFT LEVER ADJUSTMENT ������������������������������������������������������...
  • Page 5 Oil and Oil Filter Replacement ����������������������������������������������������������������������������������107 Oil Capacity ���������������������������������������������������������������������������������������������������������������108 Spark Plug �����������������������������������������������������������������������������������������������������������������109 Idling ��������������������������������������������������������������������������������������������������������������������������109 AIR INTAKE AND EXHAUST SYSTEM ����������������������������������������������������110 Exhaust Detecting System ���������������������������������������������������������������������������������������� 110 Air Intake Valve ��������������������������������������������������������������������������������������������������������� 110 Valve Clearance �������������������������������������������������������������������������������������������������������� 111 Air Filter ��������������������������������������������������������������������������������������������������������������������� 112 Throttle Body ������������������������������������������������������������������������������������������������������������� 112 COOLING SYSTEM ����������������������������������������������������������������������������������113 Radiator and Cooling Fan �����������������������������������������������������������������������������������������...
  • Page 6 Drive Chain Inspection ����������������������������������������������������������������������������������������������121 Drive Chain Tension Adjustment �������������������������������������������������������������������������������123 BRAKE SYSTEM ������������������������������������������������������������������������������������� 125 Front Brake Lever Inspection ������������������������������������������������������������������������������������125 Rear Brake Pedal Inspection ������������������������������������������������������������������������������������125 Brake Fluid Level Inspection �������������������������������������������������������������������������������������126 Brake Fluid Replenishment ���������������������������������������������������������������������������������������127 Brake Disc Inspection �����������������������������������������������������������������������������������������������129 Brake Caliper Inspection �������������������������������������������������������������������������������������������129 Anti-Lock Braking System (ABS) �����������������������������������������������������������������������������130 SHOCK ABSORBERS �����������������������������������������������������������������������������...
  • Page 7 EVAPORATIVE EMISSION CONTROL SYSTEM ����������������������������������� 140 CLEANING AND STORAGE ������������������������������������������������������������������� 141 General Precautions �������������������������������������������������������������������������������������������������141 Washing the Vehicle ��������������������������������������������������������������������������������������������������142 Polishing the Surface ������������������������������������������������������������������������������������������������143 Windshield and Other Plastic Parts ���������������������������������������������������������������������������143 Chrome and Aluminum ����������������������������������������������������������������������������������������������143 Preparation for Storage ���������������������������������������������������������������������������������������������144 Preparation After Storage ������������������������������������������������������������������������������������������145 COMMON PROBLEMS AND CAUSES ��������������������������������������������������...
  • Page 8: Foreword

    FOREWORD Thank you for purchasing a CFMOTO vehicle, and welcome to our world-wide family of CFMOTO enthusiasts� Be sure to visit us online at www�cfmoto�com for the latest news, new product introductions, upcoming events, and more� CFMOTO is an international company that specializes in the development, manufacture, and marketing of all-terrain vehicles, utility vehicles, large displacement motorcycles, and their core components�...
  • Page 9: Evap System (Evaporative Emission Control System)

    DANGER Operating, servicing and maintaining on-road or off-road vehicles can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to cause cancer and birth defects or other reproductive harm� To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your hands frequently when servicing your vehicle�...
  • Page 10: Signal Words

    Signal Words A signal word calls attention to a safety message or messages, a property damage message or messages, and designates a degree or level of hazard seriousness� The standard signal words in this manual are: “DANGER”, “WARNING”, “CAUTION” and “NOTE”� The following signal words and symbols appear throughout this manual and on your vehicle�...
  • Page 11 READ THE OWNER’S MANUAL FOLLOW ALL INSTRUCTIONS AND WARNINGS WARNING Read, understand, and follow all of the instructions and safety precautions in this manual and on all product labels� Failure to follow the safety precautions could result in serious injuries or deaths� WARNING The engine exhaust gas from this product contains CO, which is deadly and can cause headaches, giddiness, loss of consciousness, or even death�...
  • Page 12: Introduction

    INTRODUCTION Thank you for purchasing a CFMOTO vehicle, and welcome to our world-wide family of CFMOTO enthusiasts� For safe and enjoyable operation of your vehicle, be sure to follow the instructions and recommendations in this owner’s manual� Information about major repairs are outlined in the CFMOTO Service Manual, and should only be performed by a CFMOTO service dealer and technician�...
  • Page 13: Vin And Engine Serial Number

    VIN AND ENGINE SERIAL NUMBER Please record the VIN, engine serial number and name plate information in the spaces below� Vehicle Identification Number: Engine Serial Number: Name Plate Number: Engine Serial Number Vehicle Plate...
  • Page 14: Specifications

    SPECIFICATIONS 450SS S CF400-9US Performance Max Power 49�6 Hp (37 Kw) / 9500 RPM Max Torque 28�8 ft-lb (39 N•m) / 7600 RPM Min� Turn Diameter 204�7 in (5�2 m) Top Designed Speed 118 mph (190 km/h) Size Length 78�3 in (1990 mm) Width 27�9 in (710 mm)
  • Page 15 Ignition Control System ECU Ignition Lubricating System Pressure splash Oil Capacity When changing an oil filter: 2.64 qt (2.5 L) Engine Oil Type SAE 10W-40 JASO MA2 Coolant Capacity 1100 mL + (90-150) mL Idle Speed 1400 RPM ± 140 RPM Transmission Transmission Type 6-speed, international standard gear...
  • Page 16 Capacity of Fuel Tank 3�7 gal (14 L) Average Fuel Consumption Per 100 ≤ 1.3 gal (4.8 L) Electric Components Battery 12 V / 12 Ah Headlight Turning Light Tail Light...
  • Page 17: Operator Safety

    OPERATOR SAFETY General Safety Precautions WARNING Please read this manual carefully before operating the vehicle and understand all safety warnings, precautions and operating procedures� Age Limit This model is for adults only� The operator must acquire a driving license as required by local laws and regulations, and children under the age of 12 are not allowed to ride CFMOTO’s passenger-carrying vehicles�...
  • Page 18: Equipment Modifications

    Equipment Modifications CFMOTO is concerned with the safety of our customers and of the general public� Therefore, we strongly recommend that consumers should not mount on a vehicle, any equipment that may increase the speed or power of the vehicle, or make any other modifications to the vehicle for these purposes. Any modifications to the original equipment of the vehicle create substantial safety hazards and increase the risk of body injury�...
  • Page 19 Avoid Gasoline Fires and Other Hazards Gasoline is extremely flammable and highly explosive. Fuel vapors can spread and be ignited by a spark or flame many feet away from the engine. To reduce the risk of fire or explosion, follow these instructions: •...
  • Page 20 WARNING Gasoline is highly flammable and explosive under certain conditions� Allow the engine and exhaust system to cool before filling the tank� Always be highly cautious whenever handling gasoline� Always refuel the vehicle when the engine is stopped outdoors or in a well-ventilated area� Do not smoke or allow open flames or sparks in or near the area where refueling is performed, or where gasoline is stored.
  • Page 21: Owner Responsibilities

    Owner Responsibilities Be Qualified and Responsible Read this Owner’s Manual and the warning labels on this vehicle carefully� Take a safety training course on open areas if possible and practice at low speed� Higher speed requires greater experience, knowledge and suitable riding conditions� Be familiar with the control technology and the general operations of the vehicle�...
  • Page 22: Safe Riding Gear

    Safe Riding Gear Always wear clothing suited to the type of riding for the driver and passenger, includes: 1� An approved helmet 2� Goggles 3� Gloves 4� Long-sleeved shirts or jackets 5� Long pants 6� Over-the-ankle boots According to the actual weather, you may need extra apparel, such as anti-fog goggles, thermal underwear and a face guard for cold weather�...
  • Page 23 face and jaw� Please wear detachable face masks and goggles when wearing an open-face helmet� Do not depend on eyeglasses or sunglasses for enough eye protection, as they are not rated for impact protection. Debris may fly up and break a lens, causing eye injury. Use tinted masks or goggles only during the day in bright light, do not use them at night or in poor light�...
  • Page 24 Boots Always wear closed-toe, over-the-ankle boots. Sturdy over-the-ankle boots with non-slip soles offer more protection, and allow you to put your foot properly on the foot pegs� Avoid long shoelaces that could get entangled in the vehicle components� In winter, rubber-soled boots with either nylon or leather uppers and removable felt liners are best suited�...
  • Page 25: Avoid Dangerous Riding Behaviors

    AVOID DANGEROUS RIDING BEHAVIORS The following behaviors may cause serious consequences, so instructions must be followed to avoid dangerous behaviors� Operation Errors WARNING: Operation errors may cause serious damage to the operator, passenger and people around� Read every instruction in this manual and be familiar with every function of this vehicle� Must participate in the safety training and know how to operate the vehicle properly in different situations and on different types of terrain�...
  • Page 26 Riding on Unpaved Roads WARNING: The vehicle must not ride on unpaved roads� The tires of this vehicle are designed to drive on paved roads, not suitable for use on unpaved roads such as sand, mud, puddles and dirt roads� Driving on unpaved roads will seriously affect vehicle handling, which will greatly increase the incidence of accidents�...
  • Page 27 Stunts WARNING: Do not try stunts� All stunts are dangerous, including but not limited to slippery tires, jumping, side-slip, front wheel upturn, etc� Stunt or demonstration riding can result in serious accidents� Always use normal driving methods� Inspections and Maintenance WARNING: Check vehicle’s conditions before riding and service the vehicle regularly�...
  • Page 28 Modifications WARNING: Any non-standard modifications are prohibited. Any modifications will affect vehicle handling, which can lead to accidents. It is prohibited to mount any equipment which would increase the speed or power of the vehicle, or to make any other modifications to the vehicle for these purposes�...
  • Page 29: Safety Decals And Locations

    SAFETY DECALS AND LOCATIONS Read and understand all of the safety and information labels on your vehicle for safe and proper operation� Never remove any labels from your vehicle. If a label becomes difficult to read or falls off, a replacement is available from your CFMOTO dealer�...
  • Page 31: Vehicle View

    VEHICLE VIEW Rear Left View 1: Instrument 2: Clutch Lever 3: Handlebar Switch, LH 4: Fuel Tank Lock 5: Gear Shift Lever 6: Seat Lock 7: Footrest 8: Ignition Switch Lock 9: Side Stand...
  • Page 32: Front Right View

    Front Right View 10: Passenger Handhold 11: Throttle Grip 12: Handlebar Switch, RH 13: Front Hand Brake Lever 14: Rear Brake Pedal...
  • Page 33: Operating Parts

    OPERATING PARTS Clutch Lever Clutch lever is on the left side of handlebar� The clutch is a cable clutch� Adjust the clutch lever’s distance to the handlebar by turning the clutch lever adjusting knob� Adjusting knob Front Hand Brake Lever Front hand brake lever is on the right side of handlebar�...
  • Page 34: Handlebar Switch

    Handlebar Switch, LH Left handlebar switch is on the left side of the handlebar� Functions of Left Handlebar Switch Instrument Instrument operations are detailed in the button instrument section of the manual� Pushing this switch to the right activates the right turn light� T u r n l i g h t switch Pushing this switch to the left...
  • Page 35: Handlebar Switch

    Handlebar Switch, RH Right handlebar switch is on the right side of the handlebar� Functions of Right Handlebar Switch Turn to this position to shut off the vehicle� Start and stop Turn to this position to prepare switches the vehicle for starting� Turn to this position to start the vehicle�...
  • Page 36: Locks

    Locks Fuel Tank Lock Before opening the fuel tank lock: Stop the vehicle and turn off the engine. Open the fuel tank lock cover� Insert and turn the key to release the lock� Open the fuel tank cap� Ignition switch Turn the handlebar to the left, and then Handlebar lock turn the key to the lock indicator to lock...
  • Page 37 Seat Lock The seat lock is on the left side of the vehicle� The seat can be removed by inserting the key and turning to release the lock�...
  • Page 38: Gear Shift Lever

    Gear Shift Lever The gear shift lever is on the left side of the engine� Both ends of the middle connecting rod are adjustable, and the adjusting range (D) is 0�16 ~ 0�47 in (4~12 mm)� Loosen the locking nuts at both ends�...
  • Page 39: Rear Brake Lever

    Rear Brake Lever The rear brake lever is on the right side of the engine� Step on the rear brake lever to slow down or stop the vehicle� Side Stand The side stand is on the left side of the vehicle, and is used for parking�...
  • Page 40: Passenger Handhold And Footrests

    Passenger Handhold and Footrests A passenger handhold is mounted on the motorcycle and can be held by a passenger� Footrests are mounted on the motorcycle for the operator and a passenger�...
  • Page 41: Instrument

    INSTRUMENT NOTE ODO 123456km 22:35 Due to function, adjustment, and version updates of the -5°C The name of the song_singer instrument and renewed vehicle configurations by market, some contents of the instrument may change� Please selectively refer 1 2 3 k m/ h to this section according to your vehicle�...
  • Page 42: Instrument Indicators

    Instrument Indicators ODO 123456km 22:35 -5°C The name of the song_singer AV G 12 3 k m/ h...
  • Page 43 Number Symbol State When turning signal indicators are flashing, the corresponding Flash turning lights are on� When the position light indicator is on, the position light is turned on� When the vehicle is powered on and the engine is off, the fault indicator is on.
  • Page 44 When the coolant temperature is higher than 115°C, the coolant temperature warning indicator will be turned on� Please park the vehicle according to local laws and regulations to wait for the temperature drop� If this indicator turns on frequently, contact an authorized CFMOTO service center�...
  • Page 45: Instrument Display

    Instrument Display Optional Info 1 You can select a message from the menu to be displayed here or on the main interface� Press ▲ to choose Optional Info 1. Optional Info 1: TRIP 1, TRIP 2, ODO� ODO 123456km 22:35 -5°C The name of the song_singer Ambient Temperature...
  • Page 46 Menu Coolant Temperature Press ENT to enter the menu, and please refer to the Instrument Menu section� Coolant temperature is displayed with bars� More bars light up as the coolant temperature rises� When the last bar turns red, the coolant has reached a dangerous temperature exceeding 115℃...
  • Page 47 Gear Change Reminder You can enable the Gear Change Reminder in the menu� It will remind you to change gear when the engine speed reaches the recommended gear-shifting range� ODO 123456km 22:35 -5°C The name of the song_singer Remaining Fuel km/h Remaining fuel is displayed with bars�...
  • Page 48 Gear Display Optional Info 2 You can select a message from the menu to Current gear is displayed here� be displayed here or on the main interface� The neutral gear is green� Press ▼ to choose Optional Info 2. Optional Info 2: Mileage, Voltage, Instant Fuel Economy, Average fuel consumption (of the current trip), Average riding speed, ODO 123456km...
  • Page 49 Speed Clock Current time is displayed here� Current speed is displayed here� Set the current time through the menu� Metric km/h and imperial mph can be switched Switch between a 12-hour and 24-hour clock through the menu� through the menu� Bluetooth Caller Identification Bluetooth is used to connect mobile phones and helmets�...
  • Page 50 ODO 123456km 22:35 -5°C Liuda Yong Call In km/h Engine RPM Side Stand Indicator Unit of engine speed is 1000 revolutions per minute� When the side stand is used, its indicator light is on� At this time, the motorcycle cannot be started in gear� It During the break-in period, avoid high engine RPMs�...
  • Page 51 Sports Camera ODO 123456km 22:35 -5°C Liuda Yong This feature records riding moments� It can be used Call In... only when equipped with T-BOX, and it is only for Insta 100% x3 (launch permission selectively)� You can launch permission for relevant functions permanently when t ri p1 paying the related fees�...
  • Page 52: Instrument Menu

    Instrument Menu Adjust instrument settings through the instrument menu to enhance the riding experience� ODO:223245km 22:35 km/h Settings Press menu button on the left handlebar switch to enter the Subject Style instrument menu� Units WARNING Connection Optional Info The menu mode is only allowed when the motorcycle is parked and safe�...
  • Page 53 For Main interface: press it to switch Optional Info 1 and long press it to reset trips� For the first-level menu, second-level and lower menu: press it to select the prior choice. For Music: at the main interface, press it to increase the volume and long press it to select the prior song� On the Menu interface, press it to increase the volume and long press it to select the prior song�...
  • Page 54 Instrument Settings ODO:223245km 22:35 In the instrument settings, riders can adjust and set the following km/h Settings contents: Subject Style Subject Style Units Units ODO:223245km Connection 22:35 Equipment Connection km/h Settings Optional Info Optional Info Brightness Brightness Control Trip Reset Trip Reset Overspeed alarm ODO:223245km...
  • Page 55 Subject Style ODO:223245km ODO:223245km 22:35 22:35 The main interface of the instrument is equipped with multiple km/h km/h Subject Style 设置 sets of subject styles, and you can choose your favorite one in 主题风格 the menu� 单位设置 Press ENT to enter the Menu interface� Concision 设备连接...
  • Page 56 Units ODO:223245km 22:35 Change units of speed, time and temperature to suit your km/h Settings preference� Subject Style Press ENT to enter the Menu interface� Units Press △ or ▽ to select Settings, and press ENT to enter the Connection Settings interface�...
  • Page 57 Connection ODO:223245km 22:35 Navigation, telephone calls and music functions can be used km/h Settings after the helmet is connected to the instrument via Bluetooth� Subject Style Press ENT to enter the Menu interface� Units Press △ or ▽ to select Settings, and press ENT to enter the Connection Settings interface�...
  • Page 58 Optional Info ODO:223245km 22:35 You can select one message from Optional Info 1 and Optional km/h Settings Info 2 to display on the main interface� Subject Style Press ENT to enter the Menu interface� Units Press △ or ▽ to select Settings, and press ENT to enter the Connection Settings interface�...
  • Page 59 Brightness Control ODO:223245km 22:35 km/h You can manually adjust the brightness of the instrument, or the Settings instrument automatically adjusts its brightness according to the Brightness ambient light� Trip Reset Press ENT to enter the Menu interface� Overspeed alarm Press △ or ▽ to select Settings, and press ENT to enter the Traction Control System Settings interface�...
  • Page 60 Trip Reset ODO:223245km 22:35 You can reset trip data manually� km/h Trip Reset Press ENT to enter the Menu interface� Trip1 Reset Press △ or ▽ to select Settings, and press ENT to enter the Trip2 Reset Settings interface� Press △ or ▽ to select TRIP Reset, and press ENT to enter� Press △...
  • Page 61 Overspeed Alarm ODO:223245km 22:35 Overspeed Alarm alerts you to speeding when your vehicle’s km/h Settings actual speed exceeds the speed you set� Riders should not Brightness exceed the speed limit of a road at any time� Trip Reset DANGER Overspeed alarm Speeding increases the risk of losing control of the vehicle, Traction Control System thus leading to accidents�...
  • Page 62 Traction Control System ODO:223245km 22:35 km/h Traction Control System helps the vehicle get the best traction Traction Control System possible for the riding conditions� Traction Control System Press ENT to enter the Menu interface� Press △ or ▽ to select Settings, and press ENT to enter the Settings interface�...
  • Page 63 Emergency Stop Signal (ESS) ODO:223245km 22:35 When the ESS is enabled and the vehicle performs emergency km/h Emergency Stop Signal braking, the turn lights will flash to warn people behind you. Emergency Stop Signal Press ENT to enter the menu interface� Press △...
  • Page 64 Time Settings ODO:223245km 22:35 You can adjust the time displayed on the main interface� km/h Settings Press ENT to enter the Menu interface� Traction Control System Press △ or ▽ to select Settings, and press ENT to enter the Time Settings Settings interface�...
  • Page 65 Gear Change Reminder ODO:223245km ODO:223245km 22:35 Shifting at the right RPM can effectively reduce shifting pauses, km/h Settings protect the clutch and so on� Setting the appropriate Gear Gear change reminder Change Reminder also can familiarize you with the vehicle� 语言选择/Language The recommended upshifting speed is 6500 RPM�...
  • Page 66 Language ODO:223245km 22:35 You can adjust the instrument’s language to suit your km/h 语言选择/Language preference� 中 中文 Press ENT to enter the Menu interface� English Press △ or ▽ to select Settings, and press ENT to enter the Espanol Settings interface� Press △...
  • Page 67 Reset All ODO:223245km ODO:223245km 22:35 km/h You can reset all instrument settings to factory defaults� Settings Gear change reminder NOTE: This function does not reset ODO or related functions� Press ENT to enter the Menu interface� 语言选择/Language Press △ or ▽ key to select Settings, and press ENT to enter Reset all the Settings interface�...
  • Page 68 Vehicle Information ODO:223245km 22:35 In the Vehicle Information menu, users can inspect the following km/h Vehicle Information contents� Information Information Miles Info Miles Info Warning Warning Service Service Version ODO:223245km 22:35 km/h Vehicle Information Version...
  • Page 69 Information ODO:223245km 22:35 On the Information interface, you can view the coolant km/h Vehicle Information temperature, battery voltage and distance before refueling� Information Press ENT to enter the Menu interface� Miles Info Press △ or ▽ to select the Vehicle Information, and press ENT Warning to enter the Vehicle Information interface�...
  • Page 70 Miles Info ODO:223245km 22:35 km/h ODO, TRIP 1, TRIP 2, average speed, fuel consumption, driving Miles Info time can be inspected here� Press ENT to enter the Menu interface� Mileage 528364 ( km ) Total Riding Time 21361:00.00 ( h ) Press △...
  • Page 71 Warning ODO:223245km 22:35 On the Warning interface, you can view faults or warnings when km/h Warning the vehicle system detects a fault� When a fault occurs, please Maintenance Of Maturity! remove it as soon as possible, and contact an authorized CFMOTO service center if necessary�...
  • Page 72 Service ODO:223245km 22:35 On the Service interface, you can view the service information km/h Vehicle Information of the vehicle� When the service mileage is reached, the vehicle Information will remind you to carry out service� Miles Info Press ENT to enter the Menu interface� Warning Press △...
  • Page 73 Version ODO:223245km 22:35 Software and hardware versions of the instrument are displayed km/h Vehicle Information here� Version Press ENT to enter the Menu interface� Press △ or ▽ to select Vehicle Information, and press ENT to enter the Vehicle Information interface� Press △...
  • Page 74 Telephone ODO:223245km 22:35 On the Telephone interface, you can check the following km/h Telephone contents: Contacts Contacts Recent Calls Recent Calls NOTE: Before using the telephone, the equipment must be correctly connected, and the phone helmet should be connected to the instrument�...
  • Page 75 Contacts ODO:223245km 22:35 On the Contacts interface, you can view the contacts recorded km/h Telephone by their Bluetooth-connected mobile phones and dial the Contacts numbers� Recent Calls Press ENT to enter the Menu interface� Press △ or ▽ to select Telephone, and press ENT to enter the Telephone interface�...
  • Page 76 Recent Calls ODO:223245km 22:35 On the Recent Calls interface, you can view recent calls km/h Telephone recorded by the Bluetooth-connected mobile phone and dial the Contacts numbers� Recent Calls Press ENT to enter the Menu interface� Press △ or ▽ to select Telephone, and press ENT to enter the Telephone interface�...
  • Page 77 Telephone Interconnect (If Equipped) ODO:223245km 22:35 The Telephone Interconnect interface allows you to use the km/h Phone Connection projection screen function after it is connected� Equipment:XXXXXXXX The vehicle owner has two options through the CFMOTO PLAY Passcode:00000000 app to achieve this function: Scan the QR code to 1�...
  • Page 78 In the interconnected condition, navigation data can be projected to the Telephone Interconnect interface� When in the projection interface, press ‘return’ to return to the navigation map� Without input, it will automatically return to the main interface after 30 seconds� Press ‘return’ again to return to the menu� Conversely, press ENT twice to return to the projection interface�...
  • Page 79 Music ODO:223245km 22:35 On the Music interface, you can play songs on the phone km/h Music through Bluetooth, and through the instrument you can switch songs, pause music, adjust volume and use other functions� Luna stvden danfuse Press ENT to enter the Menu interface� 1:40 3:40 Press...
  • Page 80: Operating Your Vehicle

    OPERATING YOUR VEHICLE Break-In Period The break-in period for this vehicle is the first 600 miles (1000 km). Maintain the vehicle according to the break-in period requirements� The following items should be observed during the break-in period: 1� Do not run high engine speeds immediately after the engine starts� Allow the engine to warm for 2 ~ 3 minutes at idle speed and let oil flow into all engine lubricating parts.
  • Page 81: Daily Safety Inspection

    Daily Safety Inspection Inspecting the following items before daily riding will help keep your vehicle safe and reliable� If anything abnormal appears, please refer to the Maintenance and Adjustment section or contact your dealer� Do not operate the vehicle in an abnormal condition, as it may lead to serious damage or accidents� Item Content Engine oil...
  • Page 82 Luggage Inspect the luggage to see whether it is fastened securely, and make sure the luggage height is in line with local regulations� (if equipped) Coolant Inspect the coolant level to see whether it is proper� Instrument Inspect the instrument’s fault indicators and inspect the fuel to see whether the fuel is enough�...
  • Page 83: Starting

    Starting Sit on the vehicle supported with the side stand up� Turn on the ignition switch� Place the gear in Neutral� Turn the stop switch to position “ ”� Press the start button� CAUTION Running an engine at high RPMs in low temperatures will impact the lifespan of the engine� Always warm the engine at a low speed�...
  • Page 84: Starting Off

    Starting Off Grip the clutch lever, put the vehicle into gear 1, then slowly release the clutch lever while at the same time gently applying the throttle� Shifting, Riding Grip the clutch lever and release the throttle� Shift the gearshift lever upward for higher gears as required� Release the clutch lever and slowly apply the throttle at the same time to complete the gear shift�...
  • Page 85 WARNING Luggage sliding will affect riding performance, so inspect luggage to confirm it is properly secured on the vehicle and to ensure that its width does not exceed 0�15m from the handlebar on either the left or right side� In the event of an accident, the damage from crashing could be more serious than it looks� Inspect the vehicle completely to make sure it is safe, or take the vehicle to a CFMOTO dealer for inspection�...
  • Page 86 Brake Release the throttle when applying the brake, and use front and rear wheel brakes for braking at the same time� Finish braking before turning, and shift to a lower gear according to the speed required� On a long downhill ride, please leverage the brake force of the engine and shift to lower gears, but do not allow the engine to operate with high RPM�...
  • Page 87 Parking Stop the vehicle with brake� Shift the gear to Neutral� Turn off the ignition switch. Park the vehicle on a firm, level ground. Use a side stand to support the vehicle� Turn the handlebar left to the maximum, and lock the steering with the key� Remove and take away the key�...
  • Page 88 SAFETY OPERATION Safe Riding Tips The following items are applicable for daily motorcycle use and should be carefully observed for safe and effective vehicle operation: For safety, goggles and a helmet are strongly recommended. You must be aware of traffic regulations for the safe riding�...
  • Page 89 Practice your operating skills cautiously and slowly in an open area and hold the fuel tank with the knees for better stability� When there is a quick acceleration, shift to a lower gear to obtain the necessary power� Do not downshift at high RPM to avoid damage to the engine� Avoid unnecessary use of fabric tape which may entangle the rider or motorcycle�...
  • Page 90 MAINTENANCE Careful and periodic maintenance will help keep your vehicle in the safest, most reliable condition� Inspection, adjustment, and lubrication of important components are explained in the Periodic Maintenance Chart� Inspect, clean, lubricate, adjust, and replace parts as necessary� When inspection reveals the need for replacement of certain parts, always use original parts from your dealer�...
  • Page 91 Key Points of Lubrication Schedule Check all components at the intervals outlined in the Periodic Maintenance Chart� Items not listed in the schedule should be lubricated at the general lubrication interval� • Change lubricants more often under severe conditions, such as being used in wet or dusty conditions�...
  • Page 92 Break-In Maintenance Chart Break-In Maintenance Interval Item (Service whichever interval comes first) Calendar Miles Notes Engine Oil and oil filter 1000 Replace� ■ Coarse oil filter 1000 Clean� ■ Idle 1000 Coolant 1000 Inspect� ■ Throttle system 1000 Electrical system Functions of electrical parts 1000 ■...
  • Page 93 Break-In Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Wheels Tire condition 1000 Inspect� Tire pressure 1000 Suspension Inspect for oil leakage(maintain front forks and the Rear and front shock absorbers 1000 rear shock absorber ■ according to the requirement and purpose)�...
  • Page 94 Break-In Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Other parts Fault control memory 1000 Read with PDA� ■ Lubricate, and Movable parts 1000 inspect their ■ flexibility. Inspect their Bolts and nuts 1000 ■ firmness. Inspect them for damage, bending Cables 1000...
  • Page 95 Periodic Maintenance Chart Periodic Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Engine Engine Oil and oil filter 3000 5000 Replace� Coarse oil filter 3000 5000 Clean� Inspect and repair or replace if Clutch 3000 5000 ■ necessary�...
  • Page 96 Periodic Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Electrical system Functions of electrical 6000 10000 Inspect and repair or replace if necessary� ■ parts Battery 3000 5000 Inspect and recharge if necessary� Fuses or circuit 3000 5000 Inspect and replace if necessary�...
  • Page 97 Periodic Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Brake Front and rear braking systems 6000 10000 Inspect and repair or Brake discs 6000 10000 replace if necessary� Brake pads 6000 10000 ▲ Inspect and Brake fluid level 6000 10000 replenish if...
  • Page 98 Periodic Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Suspension Inspect and repair or Suspension system 3000 5000 ■ replace if necessary� Inspect for oil leakage(maintain front forks and rear Front and rear shock absorbers 6000 10000 shock absorber ■...
  • Page 99 Periodic Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Cooling system Inspect and Coolant level 6000 10000 replenish if necessary� Radiator fan function 6000 10000 Inspect and repair or ■ replace if necessary� Cooling hoses 6000 10000 ■...
  • Page 100 Periodic Maintenance Interval (Service whichever interval comes first) Item Calendar Miles Notes Other parts Fault control memory 6000 10000 Read with PDA� ■ Lubricate, and inspect their Movable parts 6000 10000 ■ flexibility. Bolts and nuts 6000 10000 Inspect their firmness. ■...
  • Page 101 CLUTCH LEVER FREE PLAY Inspect the flexibility of the clutch lever. Straighten the handlebar� Slowly apply the clutch lever until the resistance is evident� The free play distance of the clutch lever is within the following range� Free play: 0�39 in ~ 0�79 in (10 mm ~ 20 mm) WARNING Inadequate free play for the clutch lever can strain the clutch cable and affect clutch engagement, causing slippage and excessive wear�...
  • Page 102 GEARSHIFT LEVER ADJUSTMENT The gearshift lever is adjustable to suit personal riding habits� Range: ± 0�2 in (5 mm) 0�2 in Adjusting the gearshift lever 0�2 in Loosen the lock nuts � Rotate clockwise the center connecting rod to raise the gearshift lever�...
  • Page 103 TOOL KIT Tool kit is usually under the cushion and can help maintain and disassemble some parts of the vehicle�...
  • Page 104 FUEL SYSTEM Fuel Tank Refilling Avoid spilling fuel to the outside of the fuel tank when filling. If a spill occurs, wipe it off immediately to avoid pollution or causing danger� Fuel tank volume: 3�7 gal (14 L) DANGER Gasoline is flammable, so fuel should be filled in a ventilated area. Before refueling, turn off the engine and wait for the engine and muffler to cool.
  • Page 105 Fuel Requirements This motorcycle is recommended to use only unleaded gasoline (87# or higher)� CAUTION Do not use leaded gasoline, as it will destroy the catalytic converter� For further understanding, please consult related materials about the catalytic converter� Be sure to use fresh gasoline� Gasoline oxidation will result in loss of octane and volatile compounds� It also produces colloidal and lacquer deposits which could damage the fuel system�...
  • Page 106 ENGINE ASSEMBLY For the engine, transmission, clutch and other parts to work properly, make sure that the oil level is between the upper and lower lines from the oil view window, and check and replace the oil according to the Periodic Maintenance Chart� Long time use of engine oil will not only produce dirt and metallic impurities, but the oil will also consume itself�...
  • Page 107 Oil and Oil Filter Replacement Park the v ehicle on level ground� Idle the engine for several minutes. Then turn off the engine. WARNING arming up the engine for a long period may lead to high temperature of the engine and oil� Please wear suitable protective clothing and gloves when changing oil�...
  • Page 108 Remove the oil filler screw plug � Fill with 2�64 qt (2�5 L) oil of SAE 10W/40, JASOMA2� Remount the oil filler screw plug. Idle the engine for several minutes, allowing the oil to flow into the oil filter. Turn off the engine. Inspect the oil level and adjust it as necessary until the required level is reached�...
  • Page 109 Spark Plug The spark plug should be replaced in accordance with the Periodic Maintenance Chart� Its disassembly should only be performed by an authorized dealer� Spark plug type: BN8RTI Spark plug clearance : 0�03 in ~ 0�04 in (0�8 mm ~ 1 mm) Torque: 8�8 ft-lb ~ 11�1 ft-lb (12 N•m ~ 15 N•m) Idling The idling speed of this vehicle has been adjusted at the factory...
  • Page 110 AIR INTAKE AND EXHAUST SYSTEM Exhaust Detecting System Exhaust detecting system depends on two oxygen sensors mounted on exhaust pipes, and they can detect the air & fuel combustion degree by measuring oxygen density and transferring it as an electrical signal to the ECU� If the ECU determines that combustion is not thorough, it will adjust fuel injection in accordance with signals from the Throttle Position Sensor and Intake Air Temperature sensors�...
  • Page 111 Valve Clearance The valves and valve seats will wear during operation, thus the need for adjustment after being used for a period of time� WARNING When valves and valve seat tappets are wore during use, and if adjustment of the valve clearance is not performed, it will eventually result in no clearance or cause the valves remaining partly open, which reduces performance, creates valve noise, and can cause serious engine damage�...
  • Page 112 Air Filter A clogged air filter restricts air flow, increases fuel consumption, reduces engine performance, and causes spark plug fouling� The air filter element must be cleaned in accordance with the Periodic Maintenance Chart� When riding in dusty, rainy, or muddy conditions, the air filter element should be serviced more frequently than the recommended interval in the Periodic Maintenance Chart.
  • Page 113 COOLING SYSTEM Radiator and Cooling Fan Inspect the radiator fins for deformation and obstruction by mud, and clean off any obstruction with clean water� WARNING When the fan is working, prevent your hands and clothing from getting inside the fan to avoid any injury� Using high-pressure water to clean the vehicle could damage the radiator fins and reduce the radiator’s effectiveness.
  • Page 114 Coolant Coolant absorbs heat from the engine and transfers it to the air by the radiator� If the coolant level is too low, the engine will overheat and may suffer from severe damages. Inspect the coolant level daily before riding the motorcycle and perform maintenance in accordance with the Periodic Maintenance Chart� Replenish the coolant if its level is too low�...
  • Page 115 CAUTION Do not add tap water to the coolant system, for it will cause deposit inside the cooling system� When the temperature is below 0°C, ice will occur and severely affect the coolant system. Available bottled antifreeze in the market contains anti-corrosion and anti-rust chemicals� When it is diluted, it loses its anti-corrosion and anti-rust function�...
  • Page 116 Coolant Level Inspection Support the vehicle upright on a level surface� Inspect the coolant level in the reservoir � If the level is at area ‘A’: Drain out the redundant coolant until it is at area ‘B’� If it is at area ‘B’: The coolant is at the proper level� If the level is at area ‘C’...
  • Page 117 Coolant Replenishment Open the reservoir cover and replenish coolant to area B shown on the previous page� CAUTION If coolant needs to be replenished frequently, or the reservoir is completely dry, there is probably a leak in the system� Have the cooling system inspected by an authorized dealer� Only recommend the original CFMOTO coolant.
  • Page 118 TIRES AND CHAINS This vehicle only uses tubeless tires, rims and inflating valves. Only use the recommended standard tires, rims and inflating valves. Do not mount inner tube tires on tubeless rims. Improper mounting of tires may cause air leakage� Do not mount an inner tube inside a tubeless tire� Tire Specifications Front wheel 110/70 R17...
  • Page 119 Most countries have their own regulations of minimum tread depth� Please follow local regulations� When mounting new rims or tires, always inspect the wheel balance of the tires� CAUTION In order to ensure safe and stable operation, please only use the tire and tire pressure recommended� If the tire is punctured and repaired, please do not ride the vehicle over 60 mph (100 km/h) until 24 hours after, and the speed cannot exceed 80 mph (130 km/h) at any other time�...
  • Page 120 Tire Friction When tire tread wears too severely and the tire cannot be used, the tire becomes more susceptible to punctures and failures� An accepted estimate is that 90% of all tire failures occur during the last 10% of tire service life, so it is unsafe to continue to use bald tires� In accordance with the Periodic Maintenance Chart, measure the depth of the tread with a depth gauge, and replace any tire that has been worn down to the minimum allowable tread depth�...
  • Page 121 Drive Chain Inspection The looseness and lubrication of the drive chain must be inspected daily before riding and safety cautions in the Periodic Maintenance Chart must be observed to prevent excessive wear� If the chain becomes badly worn or maladjusted, it will cause the chain to be to too loose or too tight� If the chain is too tight, it will accelerate the wear to the chain, sprocket, rear sprocket and rear rim�...
  • Page 122 Chain Tension Inspection Shift the gear into Neutral� Park with the side stand� Push up the chain to inspect its tension� If the chain tension is not in line with relevant specifications, then adjust it to the standard� Standard value: 0�98 in ~ 1�38 in (25 mm ~ 35 mm) 0�98 in ~ 1�38 in NOTE: The wear of the chain is not always uniform, and the tension...
  • Page 123 Drive Chain Tension Adjustment Loosen the eccentric hub lock bolt � Use the adjuster tool in the tool kit, and insert it into the teeth of the eccentric chain adjuster � Make adjustments from the right side of the vehicle� Rotate the eccentric chain adjuster clockwise to loosen the chain, and rotate it counterclockwise to tighten the chain�...
  • Page 124 Wear Inspection Shift the transmission into Neutral� 12�6 in Support the vehicle with the side stand� Apply chain tensioning or hang a 22 lb (10 kg) weight from the chain� Measure the elongated length between 20 links� If the measured length exceeds the standard limit, replace the chain with a new one�...
  • Page 125 BRAKE SYSTEM In order to maintain excellent performance of your vehicle and personal safety, please inspect and maintain the vehicle according to the Periodic Maintenance Chart� Make sure all the parts of the brake system are in a good state� If any damage occurs to the brake system, please stop riding and have your vehicle inspected and maintained by an authorized dealer�...
  • Page 126 Brake Fluid Level Inspection Support the vehicle vertically on level ground, and confirm the brake fluid reservoirs are level. Inspect the front and rear brake reservoir fluid levels. If the brake fluid level is at area ‘A’: Drain out the redundant fluid until it is at area ‘B’. If the brake fluid level is at area ‘B’: The level is proper.
  • Page 127 Brake Fluid Replenishment WARNING Brake fluid can irritate the skin. Keep brake fluid out of the reach of children. Keep brake fluid away from skin, eyes or clothing. Wear protective clothing and goggles when operating the vehicle� If brake fluid is swallowed, see a doctor immediately. If brake fluid touches the skin, wash the skin with plenty of clean water.
  • Page 128 Front Brake Fluid Reservoir Remove the cover and reservoir gasket � Replenish brake fluid to area ‘B’. Remount the cover and reservoir gasket� Rear Brake Fluid Reservoir Remove screws � Remove the cover and reservoir gasket � Replenish brake fluid to area ‘B’. Remount the cover and reservoir gasket�...
  • Page 129 Brake Disc Inspection Inspect brake discs periodically for any damage, out of shape, cracks or wear� Damaged brake discs may cause braking failure� Worn-out brake discs will decrease braking performance� If brake discs are damaged or exceed the wear limit, contact an authorized dealer to replace them with new ones immediately�...
  • Page 130 Anti-Lock Braking System (ABS) ABS is a safety system that prevents locking of the wheels when riding in a straight line or a curve without the influence of lateral forces. With the assistance of ABS, when riding on gritty, water-logging, sliding or other low-adhesive force roads, the vehicle can use its full brake force and will face no risk of wheel locking�...
  • Page 131 SHOCK ABSORBERS Shock Absorber Inspection Holding the handlebar and front brake, compress the front fork for several times to inspect it to see whether its working is smooth� Visually inspect the front shock absorbers for oil leaks and front fork for scratches or friction noise� After riding, inspect the front fork to see whether it has mud, dirt or debris, and if so, clean them, or they will lead to oil seal damage and shock absorber oil leak�...
  • Page 132 ELECTRICAL SYSTEM AND LIGHTS Battery It is equipped with lead-acid battery for starting. When the vehicle is not in use for a long time (≥2 months), the battery needs to be removed for storage� However, for optimal battery life, you must properly charge the battery to provide enough power for the starter motor�...
  • Page 133 Battery Maintenance Clean the battery case with a soft brush dipped in a mixture of baking soda and water� Use a wire brush to remove corrosion on the positive and negative lug plates and positive and negative anodes� Always keep the battery fully charged, or the battery may be damaged� If the vehicle is driven infrequently, inspect the battery voltage weekly with a voltmeter�...
  • Page 134 WARNING Do not remove the battery’s sealing strip, or the battery will be damaged� Do not mount an ordinary battery in this motorcycle, or the electrical system will not work properly. When removing the battery, firstly disassemble the negative pole and then the positive pole� During mounting, the connection sequence of positive and negative poles is opposite to that of disassembly�...
  • Page 135 Battery Removal Place the vehicle on flat ground and park it. Completely turn off the engine and power supply of the vehicle. Insert the key into the cushion lock� Remove cushion � Remove the black negative wire (-)� Remove the red positive pole wire (+)� Remove the battery pull belt �...
  • Page 136 Battery Mounting Park the vehicle on flat ground. Ensure that the vehicle’ s key is in the closed position� Put in the battery� Mount battery belt� Mount the red positive pole wire (+)� Mount the black negative wire (-)� Remount the dust cover and seat� WARNING Avoid direct touching with the skin, eyes and clothing�...
  • Page 137 Lights Headlight and fog light are adjustable� Rotate the light adjusting knob to adjust light� CAUTION Adjustment of high / low beams should be in accordance with local regulations� The standard is based on the light emitted when front and rear wheels touch down the ground and the rider sits on the vehicle� All the lights are LED lights�...
  • Page 138 Fuses Fuse box is under the seat, it is visible after removing the seat� If a fuse is blown, inspect the electrical system for damage and replace the fuse with the new one� WARNING Do not use any wire to substitute for the standard fuse� Replace a blown fuse with a new one of the same ampere�...
  • Page 139 CATALYTIC CONVERTER This motorcycle is equipped with a catalytic converter in the exhaust system� Platinum and rhodium contained inside the converter will react with carbon monoxide and convert hydrocarbons into carbon dioxide and water� For proper operation of the catalytic converter, the following cautions must be followed: Only use unleaded gasoline.
  • Page 140 EVAPORATIVE EMISSION CONTROL SYSTEM This vehicle is equipped with an EVAP System� Please contact a CFMOTO dealer if the EVAP System has failed� Do not modify the System, or the System will not meet requirements for environmental regulations� After disassembly and repair, tube connections should be well connected without air leakage, blocking, and tubes should be without being squeezed, broken or damaged, etc�...
  • Page 141 CLEANING AND STORAGE General Precautions Always keeping your motorcycle clean and in best performance will extend the vehicle’s service life� Protecting your motorcycle with a high quality, breathable motorcycle cover� • Always clean the motorcycle after the engine and exhaust system have cooled� •...
  • Page 142 Washing the Vehicle • Rinse the vehicle with cold water to remove any loose dirt� • Mix a bucket of detergent (specialized for motorcycles or automobiles) with water� Use a soft cloth or sponge to wash your motorcycle� If necessary, use a mild degreaser to remove any oil or grease� Start at the top of the motorcycle and wash bottom parts last�...
  • Page 143 Polishing the Surface After washing your motorcycle, polish the painted metal and plastic surfaces with a specialized motorcycle/ automobile wax� Wax should be applied every three months or as required, to avoid the surface from having satin lines or being lackluster� Always use non-abrasive wax and apply them according to the instructions�...
  • Page 144 DANGER Special care must be given to tires, and it should be noted that rubber-protective agents applied to tires will not affect their functions. If tires are not treated properly, it may decrease the adhesive force between the tire and ground, possibly causing a loss of control� Preparation for Storage Clean the entire vehicle thoroughly�...
  • Page 145 Lubricate drive chains and all cables� Remove the battery� Store it in a cool and ventilated place� Ensure that the battery is fully charged according to the Periodic Maintenance Chart� Wrap plastic bags over the muffler exhaust pipe to prevent moisture from entering. Put a cover over the motorcycle to prevent dust and dirt�...
  • Page 146 COMMON PROBLEMS AND CAUSES Problem Component Cause Solution No fuel in fuel tank Refuel Fuel system Pump blockage or damage: poor fuel quality Clean or replace Spark plug failure: excessive carbon deposits, too Inspect or replace long-time usage Spark plug cap failure: Poor contact or burning Inspect or replace Ignition coil failure: poor contact or burning Inspect or replace...
  • Page 147 Intake and exhaust valves, excessive carbon deposits Repair or replace Valve and piston in the piston: poor fuel quality and poor oil quality Clutch slips; poor oil quality, too long-time use and Adjust or replace Clutch overloading Insufficient Cylinder, piston rings wear; poor oil quality and too Replace oil Cylinder and ring long-time use...
  • Page 148 Battery No electricity Charge or replace Left switch Horn button failure or damage Adjust or replace Failed horn Cables Poor contact Adjust or repair Horn Horn damage Adjust or replace The listed above are the common problems of a motorcycle� If your motorcycle has certain problems (especially in the electronic fuel injection system, fuel evaporation system), please contact an authorized CFMOTO dealer to inspect and repair the vehicle in time�...
  • Page 149 WARRANTY INFORMATION Change of Ownership If you sell your vehicle, any valid remainder of the warranty can be transferred to the new owner� Please record the details of the exchange below and inform an authorized CFMOTO dealer: Change of Original Purchaser 2nd Owner 3rd Owner 4th Owner...
  • Page 150 CFMOTO LIMITED WARRANTY Dear Customer: Thank you for purchasing a CFMOTO product� If any component on your vehicle is found to be defective in materials or workmanship within the terms and conditions of this CFMOTO Motorcycle Limited Warranty, the defective component will be repaired or replaced (at the option of CFMOTO) without charge for parts and/or labor at any authorized dealer located within the country of purchase�...
  • Page 151 3� EXCLUSIONS FROM WARRANTY COVERAGE: This Warranty excludes damages or failures resulting from the following acts or circumstances: • Fire • Collision • Theft • Unavoidable natural disasters • Improper storage or transportation • Failure or negligence in the performance of periodic vehicle maintenance •...
  • Page 152 4� OWNER’S RESPONSIBILITIES: The vehicle’s owner must properly use, maintain, and care for the vehicle as outlined in the CFMOTO Owner’s Manual� Any warranty repairs must be performed exclusively by CFMOTO authorized Dealers� Any warranty work performed by anyone other than an authorized CFMOTO Dealer will not be covered under the CFMOTO Limited Warranty policy�...
  • Page 153 7� NOISE CONTROL SYSTEM AND TAMPERING: Federal law prohibits any of the following acts or causing thereof: a) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use�...
  • Page 154 Emissions Components - Warranty Period: CFMOTO warrants that each new 2021 and later CFMOTO motorcycle that includes as standard equipment a headlight, taillight, stoplight and is street-legal, is free from defects in material and workmanship which cause such motorcycle to fail to conform with applicable regulations of the United States Environmental Protection Agency for a period of use of five (5) years or 30,000 km (18,641 miles), whichever occurs first for 300cc or above motorcycles, and a period of use of five (5) years or 12,000 km (7456 miles), whichever comes first for 125cc motorcycles.
  • Page 155 III� The following parts are considered emission-related components for evaporative permeation emissions (If applicable): • Fuel Tank • Fuel Cap • Fuel Line • Fuel Line Fittings IV� Emission-related components also include any other part whose primary purpose is to reduce emissions or whose failure would commonly increase emissions without significantly degrading engine/ equipment performance�...
  • Page 156 10� INTEGRATION: This limited warranty supersedes any and all oral, express, or written warranties, statements, or undertakings that may previously have been made, and contains the entire agreement of the parties with respect to the warranty of CFMOTO vehicles� Any and all warranties not contained in this Agreement are specifically excluded�...
  • Page 157 CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS In California, new motor vehicles must be designed, built and equipped to meet the State’s stringent anti-smog standards� CFMOTO Powersports, Inc� must warrant the emission control systems on your motorcycle for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your motorcycle�...
  • Page 158 OWNER’S WARRANTY RESPONSIBILITIES: - As the motorcycle owner, you are responsible for the performance of the required maintenance listed in your owner’s manual� CFMOTO Powersports, Inc� recommends that you retain all receipts covering maintenance on your motorcycle, but CFMOTO Powersports, Inc� cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance�...
  • Page 159 GENERAL TORQUE CHART Type Torque (N•m) Type Torque (N•m) M5 bolt and nut 5 ± 1 M5 screw 4 ± 1 M6 bolt and nut 10 ± 1 M6 screw 9 ± 1 M8 bolt and nut 20 ~ 30 M6 flange bolt and nut 12 ±...
  • Page 160 Tighten the screw to 110N•m, fastening the bolts of upper/lower Upper triple clamp upper side fastening triple clamp, loosen the screw screw, then tighten the � screw to 20~25N•m Lower side of front shock absorber and M8×25 20~25 front wheel axle screw Upper triple clamp fastening screw M8×20 20~25...
  • Page 161 Rear fork shaft Front wheel axle M16×168 75~85 Tooth ring, brake disk and rim M8×28 RPM sensor and front shock absorber M6×16 RPM sensor and rear caliper Front wheel RPM sensor wire clip M6×12 Front brake inlet pipe and lower triple clamp Front brake fluid inlet pipe wire clip and frame...
  • Page 162 ABS bracket and frame M6×22 Rear brake master cylinder and RH front M8×25 foot pedal bracket Rear caliper mounting plate and caliper Rear reservoir and frame M6×16 Foot brake lever assembly and RH pedal M8×25 bracket Clutch lever assembly Built-in bolt Fastening handlebar screw (inner hex) M8×30 Handlebar locating screw (inner hex)
  • Page 163 Front pedal bracket and rear fork shaft M12×35 Front pedal bracket and frame bolt M8×30 Front pedal bracket panel and Front pedal M6×12 bracket Rear pedal bracket and frame bolt M8×20 Front pedal seat fitting screw Reservoir mounting bolt M6×14 R a d i a t o r l o w e r m o u n t i n g p o i n t a n d connecting bracket assembly connecting M6×25...
  • Page 164 TELEMATICS BOX T-BOX is an optional part, and when you purchase a vehicle, you’d better check with dealer if it’s equipped with a telematics box, or T-BOX� The T-Box is an intelligent vehicle terminal that builds a communication bridge between owners and vehicles through the CFMOTO RIDE APP installed on a mobile device�...
  • Page 165 6AQV-380101-3300-13 US235 ZHEJIANG CFMOTO POWER CO., LTD. MANUFACTURED BY: Add:NO.116,Wuzhou Road, Yuhang Economic Development Zone,Hangzhou 311100,Zhejiang Province,China Tel:86-571-86258863 Fax:+86-571-89265788 E-mail:service@cfmoto.com.cn http://global.cfmoto.com DISTRIBUTED BY: DISTRIBUTED BY CFMOTO POWERSPORTS INC. CANADA MOTOR IMPORT INC. 3555 Holly Lane N. Suite #30, Plymouth MN, 55447, USA 24 rue Industrielle, Saint-Benoît Labre, Toll free: (888) 8-CFMOTO (823-6686) Québec, Canada, G0M 1P0...

Table of Contents